Vision T9600HRT Use and care manual

CALIBRATION GUIDES
1
Date of last revision: 12.05 TREADMILL.CALIB.REV4
CONFIRM CONFIGURATION
STEP 1 ENTER ENGINEERING MODE
• With the SAFETY KEY in place, hold the “ELEVATION UP” and “SPEED
DOWN”
buttons for 5 seconds. The profile window will read ““DDGGAA33JJ””and
the function window will read ““NNOONNEE””.
• You are now in ENGINEERING MODE.
STEP 2 CHECKING CONFIGURATION
• Press the “ELEVATION UP” button until ““EENNGG11””appears in the function
window. Press
“SELECT” . The function window will read ““224400CC””or ““IICC0000””.
““55..66””or ““55..99””will appear in the elevation window and ““1100””will appear in
the speed window.
• To change configurations, press the
“SPEED UP” or “SPEED DOWN” button.
• Press the
“SELECT” button to update data.
AUTO-CALIBRATION
STEP 3 ENTER ENGINEERING MODE
• “ELEVATION UP” to ““PP1144””. The elevation window will read ““EENNGG””and the
speed window will read ““OOUUTT””. Press the “STOP” button. The function
window will read ““EENNGG11””.
STEP 4 ENTER AUTO-CALIBRATIONS
• Press the “ELEVATION UP” or “SPEED UP” to ““EENNGG44””.
• Press “SELECT” .
STEP 5
• Press “START” . The treadmill will calibrate itself. This will take about 3 to
5 minutes. When AUTO is complete, ““EENNDD””will appear in the window.
Wait 10 to 15 seconds and the treadmill will reset itself to ““PP11””.
STEP 6
• Press “START” to test the treadmill.
T9600HRT and T9600HRT Comfort v5.6, v.5.9
Calibration Guide
ILLUSTRATIONS FOR DISPLAY PURPOSES ONLY

CALIBRATION GUIDES
2Date of last revision: 12.05TREADMILL.CALIB.REV4
T9600HRT and T9600HRT Comfort v5.6, v.5.9
Calibration Guide continued
MANUAL CALIBRATIONS
STEP 1 ENTER ENGINEERING MODE
• With the SAFETY KEY in place, hold the “ELEVATION UP” and “SPEED
DOWN”
buttons for 5 seconds. The profile window will read ““DDGGAA33JJ””and
the function window will read ““NNOONNEE””.
• You are now in ENGINEERING MODE.
STEP 2 CHECKING CONFIGURATION
• Press the “ELEVATION UP” button until ““EENNGG11””appears in the function
window. Press
“SELECT” . The function window will read ““224400CC””or ““IICC0000””.
““55..66””or ““55..99””will appear in the elevation window and ““1100””will appear in
the speed window.
• To change configurations, press the
“SPEED UP” or “SPEED DOWN” button.
• Press the
“SELECT” button to update data.
STEP 3 SET MINIMUM SPEED
• Press the “ELEVATION DOWN” button until the function window reads
““PP00””. ““00””will appear in the elevation window and ““2299””should appear in
the speed window. To adjust, press
“START” .
• Press the
“SPEED UP” or “SPEED DOWN” button until the elevation
window reads ““2266--3333””. The running belt should be moving at .5 MPH.
• Press the
“SELECT” button to update the data.
STEP 4 SET MAXIMUM SPEED
• Press the “ELEVATION UP” button until the function window reads ““PP11””.
““00””will appear in the elevation window and ““332255””should appear in the
speed window. To adjust, press
“START” .
• Press the
“SPEED UP” or “SPEED DOWN” button until the elevation
window reads ““332200--333300””. The running belt should be moving at 12 MPH.
• Press the
“SELECT” button to update the data.
STEP 5 SET THE HALF MAXIMUM SPEED
• Press the “ELEVATION UP” button until the function window reads ““PP22””.
““00””will appear in the elevation window and ““116699””should appear in the
speed window. To adjust, press “START” .
• Press the
“SPEED UP” or “SPEED DOWN” buttons until the console reads
““116633--117755””. The running belt should be moving at 6 MPH.
• Press the
“SELECT” button to update the data.
ILLUSTRATIONS FOR DISPLAY PURPOSES ONLY

CALIBRATION GUIDES
3
Date of last revision: 12.05 TREADMILL.CALIB.REV4
MANUAL CALIBRATIONS continued
STEP 6 SET MINIMUM ELEVATION
• Press the “ELEVATION UP” button until the function window reads
““PP44””. ““5599””should appear in the elevation window and ““5555--7755””should
appear in the speed window.
• Press the
“SPEED UP” or “SPEED DOWN” buttons until the console
reads ““5555--7755””. The treadmill should be level.
• Press the
“SELECT” button to update the data.
STEP 7 SET MAXIMUM ELEVATION
• Press the “ELEVATION UP” button until the function window reads
““PP55””. ““5555--7755””should appear in the elevation window and ““220055--222200””
should appear in the speed window.
• Press the
“SPEED UP” or “SPEED DOWN” buttons until the window
reads ““220055--222200””. The treadmill will be at maximum elevation.
• Press the
“SELECT” button to update the data.
REMOVE AND REPLACE THE SAFETY KEY.
PRESS THE START BUTTON AND TEST THE TREADMILL.
ILLUSTRATIONS FOR DISPLAY PURPOSES ONLY
T9600HRT and T9600HRT Comfort v5.6, v.5.9
Calibration Guide continued
Address Description Default Value Min.Value MaxValue
P6 Checksum Value
P7 Max Time 99 15 99
P8 Default Weight 150 35 400
P9 Accumulated Time 0 0 6553.5
P10 Accumulated Distance 0 0 65535
P11 Belt Thickness 5 0 10
P12 Roller Diameter 60 60 60
P13 Elevation Direction (reading a/d values) 255 0 255
P14 EXIT (software ver. 5.6 and 5.9) N/A N/A N/A