Visionis VS-SS600-G User manual

VS-SS600-G
600lbs Outdoor and Gate
Maglock
ref.
Disclaimer: VISIONIS reserve the right to go ahead with any modifications of models or features or price without forewarning. All the
information and specifications stated in this document are current at the time of publication. Attention: We are not responsible for the
improper installation of this kit. If you are not handy with electrical equipment you should contact a professional electrician. You will also
need to check with your local Fire authority to see if you need anything else to comply with local Fire Codes. We are not responsible for
any damage or fees that can occur.
www.visionistech.com
[email protected]
Technology Within Your Reach
Dimensions
t este d
G e r m a ny
EMC
R
• Size: 220Lx42Wx25.5H(mm) -
8.66Lx1.65Wx1.00H(in.)
• Holding Force: 280kg (600Lbs)
• Input Voltage: 12 or 24VDC
• Current: 12V/500mA or 24V/250mA
• Suitable: Wooden door, Glass door, Metal
door, Fireproof door
• Signal Output: Lock Signal NO/COM
• Waterproof Level: IP-68
Units: mm (inches)
Features
Notice:
Please read the following instructions before installation.
A. Please handle the lock carefully. Any damage of the surface or the armature plate will reduce the magnetic force.
B. Fix the lock on the door frame and the armature plate on the door leaf. The accessories can provide better
conjunction to the lock and the armature plate.
C. Please keep the door closed when you drill holes.
D. Fasten the screws of the lock.
E. The limit value of the reed switch of the door signal detection is 0.5A/30V DC. Don’t overload.
F. Make sure the armature plate can be slightly shaken when locked, for the rubber washer need some spaces to
adjust the position of the armature plate and the lock.
G. PleaseselectthecorrectwiringforDC12VorDC24Vvoltageinput.
220 (8.66”)
25.50 (1.00”)
23 (0.90”)
154 (6.06”)5.50 (0.21”) 10 (0.39”)
8 (0.31”)
12.75 (0.50”)
24 (0.94”)
37 (1.45”)
200 (7.87”)
42 (1.65”)

VS-SS600-G
600lbs Outdoor and Gate
Maglock
ref.
Disclaimer: VISIONIS reserve the right to go ahead with any modifications of models or features or price without forewarning. All the
information and specifications stated in this document are current at the time of publication. Attention: We are not responsible for the
improper installation of this kit. If you are not handy with electrical equipment you should contact a professional electrician. You will also
need to check with your local Fire authority to see if you need anything else to comply with local Fire Codes. We are not responsible for
any damage or fees that can occur.
www.visionistech.com
[email protected]
Technology Within Your Reach
Wire Diagram
ZL Bracket
COM COM
24V DC
24V DC
White
Black
Blue
Orange
Red
White
Black
Blue
Orange
Red
NO NO
Green Green
ZL Bracket-For inward opening door. For inward opening door, ZL bracket is needed.
Step 1: There must be 2 metal washers and 1 rubber washer between armature plate and Z-shaped
bracket. Put the rubber washer between 2 metal washers. Lock the flattop screw in the middle of
armature plate to the Z-shaped plate.
Note: Make sure the armature plate can be slightly shaken when locked. This will provide better
conjunction to the magnet and reach the best efficiency.
Step 2: Drill 5 holes for the fixing the Z-shaped plate on the door fan. Make sure the positions of hole
correspond to the magnet. Fasten the Z-shaped plate into the door fan firmly. Adjust the proper
conjunction between Z-shaped plate and sheer strike plate.
Note: The Z-shaped plate should be equipped with the anti-sliding washers to avoid sliding.
Inswing door