VisionX P-RHIDBALLAST.50.V Manual

P-RHIDBALLAST.50.V
TECHNICAL INFORMATION
Vision X 50 WATT Off Road Ballast & Starter
Washington Office
901 Algona Blvd N.
Unit F
Algona, WA 98001
Ph: 888-489-9820
Fx: 253-218-2905
Arizona Office
6501 E. Greenway
Suite 103-542
Scottsdale, AZ 85254
Ph: 800-994-4460
Fx: 480-922-5655
www.visionxusa.com
Page 1 of 3
4/29/2010
m:\technical data\hid\p-rhidballast.50.v technical specifications.doc

P-RHIDBALLAST.50.V
TECHNICAL INFORMATION
Vision X 50 WATT Off Road Ballast & Starter
Washington Office
901 Algona Blvd N.
Unit F
Algona, WA 98001
Ph: 888-489-9820
Fx: 253-218-2905
Arizona Office
6501 E. Greenway
Suite 103-542
Scottsdale, AZ 85254
Ph: 800-994-4460
Fx: 480-922-5655
www.visionxusa.com
Page 2 of 3
4/29/2010
m:\technical data\hid\p-rhidballast.50.v technical specifications.doc
P-RHIDBALLAST.50.V Options
Type Order No. Output/W Lamps
EP8050DC-
USBDF9-P EP8050DC-USBDF9-P 50
Technical data
Input Voltage Range DC9V～32V
Typical Operating Voltage DC12.8V
Typical Operating Voltage DC24V
Typical Input Current 4.3A, Condition: DC 12.8V Input
Typical Input Current 2.2A, Condition: DC 24V Input
Max. Inrush Current 25A
Output Power 47W±2W (Constant Power)
Output voltage AC85V±15V (Square Pulse, RMS70V～100V)
Output Frequency 260Hz～280Hz
Efficiency：≥83%,
Ignition pulse Typical peak Voltage 23kV
Typical duration 1s
Cooling method Natural cooling
Input Protections Under voltage protection at 6V±1V
Over voltage protection at 34.5V±1V
Input connection-reverse protection
Output Protections Short circuit protection between two outputs
Open circuit protection between two outputs
Operating temperature -40℃～＋80℃
Storage temperature -40℃～＋105℃

P-RHIDBALLAST.50.V
TECHNICAL INFORMATION
Vision X 50 WATT Off Road Ballast & Starter
Washington Office
901 Algona Blvd N.
Unit F
Algona, WA 98001
Ph: 888-489-9820
Fx: 253-218-2905
Arizona Office
6501 E. Greenway
Suite 103-542
Scottsdale, AZ 85254
Ph: 800-994-4460
Fx: 480-922-5655
www.visionxusa.com
Page 3 of 3
4/29/2010
m:\technical data\hid\p-rhidballast.50.v technical specifications.doc
Warning Notice
We reserve the right to make technical changes without prior notice.
Do not attempt to handle or operate an electronic power supply (EPS) and ignitor before completely
reading and understanding this notice. Contact EPE if you are uncertain of characteristics of these
devices.
The ignitor produces starting voltages of up to 23kV and electromagnetic radiation interference,
which are hazardous to personnel and sensitive instrumentation. Do not touch any conductive parts
during operation.
Both electronic lamp ballast and ingnitor must never be installed or operated in an explosive or
volatile atmosphere. Never use the ballast or ignitor near flammable gases or liquids. See that there
will be no moisture, dust or similar which could lead to short circuits or fire.
No potential isolation is provided between line input and output. Accidentally grounding of an output
terminal by direct contact or arcing to GND can damage the unit (no warranty replacement).
All installation and repair work on this unit is only permitted by qualified personnel.
Please provide sufficient cooling condition for EPS and ignitor.
EPE does not assume liability for disregarding of this notice, incorrect use of the EPS and ignitor or
disregarding of any legal requirements. This product is subject to technical changes without prior
notice.