vita SP-A3T-UP User manual

USER S MANUAL
Bottom Loading Water Dispenser
MODEL
SP-A3T-UP
KEEP THIS MANUAL IN GOOD CONDITION
PLEASE READ THIS MANUAL CAREFULLY
BEFORE USING THE MACHINE
REV.

DIRECTORY
5
D. DISPENSING WATER
A:PART NAME
B:SAFETY PRECAUTIONS
C:GETTING STARTED
D:DISPENSING WATER
E:TROUBLESHOOTING
F:TECHNICAL PARAMETERS
G:CIRCUIT DIAGRAM
H:CLEANING
I: MACHINE INSTALLATION
1
2
3
5
6
6
7
7
8
This unit has been tested and sanitized prior to packing and shipping. During
transit dust and odors can accumulate in the tank and lines. Dispense and
dispose at least one quart of water prior to drinking any water.
After setup, it will take up to 1 hour to get water to maximum cold
temperature. During this time the compressor could run continuously. This is
normal.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Depress normal water control downward to start cold water flow.
3. Release control once desired fill level is achieved.
1.
Dispensing Cold Water
Dispensing Normal Water
Position bottle, glass, pitcher or cooking pot below spout.
2. Depress cold water control downward to start normal water flow.
3. Release control once desired fill level is achieved.
After setup, hot water will be available in 15-20 minutes.
1. Position bottle, glass, pitcher or cooking pot below spout.
2. Slide red button away from you and depress hot water control downward
to start hot water flow.
3. Release control once desired fill level is achieved.
Dispensing Hot Water
Changing Bottles
A flashing red light on your function lights alerts you when your bottle is
empty. Replace the bottle as soon as possible.
Notice: Do not dispense hot, cool or cold water if the light is flashing as
you could empty the tanks and cause the dispenser to overheat.
1. Open dispenser door.
2. Slide empty bottle out of cabinet.
3. Remove probe assembly from empty bottle. Place probe assembly on
probe hanger.
4. Set empty bottle aside.
5. Place fresh bottle outside of cabinet. Remove entire plastic cap from top of
bottle. Clean outside of new bottle with a cloth.
6.Place probe into bottle. Slide collar down until it clicks in place. Push head
down until tubes hit bottom of bottle.
7.Slide bottle into cabinet and close door.

A. PART NAME
4 1
NO PART NAME
1
2
3
4
5
6
7
8
9
10
11
12
13
Panel
push button of cold water
push button of normal water
push button of hot water
spout
front carapace
water collector
LED night light switch
heating switch
cooling switch
power cord
condenser
outlet of hot water
NOTE:
This machine can be suitable for bottle of 3or 5 gallons. Do not
use unhealthy hard water.
（）FRONT （）REAR
.NO.PART NAME
1
2
3
4
5
6
7
8
9
10
11
12
13
Install Water Bottle
Provide Electricity
Activate Heating & Cooling
Notice: This unit will not dispense hot or cold water until the switches
are activated.
Activate Nightlight
1. Open dispenser door.
2. Place probe assembly on probe hanger.
3. Place fresh bottle outside of cabinet.
4. Remove entire plastic cap from top of bottle.
5. Clean outside of new bottle with a cloth.
6. Place probe into bottle.
7. Slide collar down until it clicks in place.
8. Push head down until tubes hit bottom of
bottle.
9. Slide bottle into cabinet and close door.
Plug cord into a properly grounded wall outlet.
At this time the pump will begin to move water
from the bottle to the hot and cold tanks. It will
take up to 12 minutes to fill the tanks for the first
time. During this period the pump will run
continuously. This is normal.
To activate. Push top side of power switches in to start heating and cooling
water.
- If you do not want to heat water, push bottom side of red switch on.
- If you do not want to cool water, push bottom side of green switch on.
Push top side of blue power switch on to turn light on. Push bottom side in
to turn light off.

2 3
B. SAFETY PRECAUTIONS
WARNING
！
To reduce risk of injury and property damage, user must read this entire
guide before assembling, installing & operating dispenser.
Failure to execute the instructions in this manual can cause personal injury
or property damage.
This product dispenses water at very high temperatures. Failure to use
properly can cause personal injury.
When operating this dispenser, always exercise basic safety precautions,
including the following:
Prior to use, this dispenser must be properly assembled and installed in
accordance with this manual.
This dispenser is intended for water dispensing only. DO NOT use other liquids,
DO NOT use for other purposes. Never use any other liquid in the dispenser
other than known and microbiologically safe bottled water.
For indoor use only. Keep water dispenser in a dry place away from direct
sunlight. DO NOT use outdoors.
Install and use only on a hard, flat and level surface.
DO NOT place dispenser into an enclosed space or cabinet.
DO NOT operate dispenser in the presence of explosive fumes.
Position back of dispenser no closer than 20cm from wall and permit free
airflow between wall and dispenser. There must be at least 20cm clearance
on the sides of the dispenser to permit airflow.
Use only properly grounded outlets.
Do not use an extension cord with your water dispenser.
Always grasp plug and pull straight out from outlet. Never unplug by pulling on
power cord.
DO NOT use dispenser if cord becomes frayed or otherwise damaged.
To protect against electric shock. DO NOT immerse cord, plug, or any other part
of dispenser in water or other liquids.
Ensure dispenser is unplugged prior to cleaning.
Never allow children to dispense hot water without proper and direct supervision.
Unplug unit to prevent unsupervised use by children.
Service should be performed only by a certified technician.
Warning: DO NOT damage the refrigerant circuit.
C. GETTING STARTED
The adult should supervise the children in order to make sure the children can
not play with the appliance.
The appliance is not intended for use by persons (including children) with
reduce physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safely.
This appliance is intended to be used in household and similar applications
such as: -staff kitchen in hotels, motels and other residential type
-farm houses; -by clients in hotels, motels and other residential type
environments; -bed and breakfast type environments.
If the supply cord is damaged, it must be replaced by a special cord or assembly
avaiable from the manufacture or its service agent.
Never turn the machine upside down or lean it more than 45 .
Thermostat has be adjusted. No need to adjust it by yourself. When the machine
is under the ice point and blocked by ice, the cooling switch must be closed for 4
hours before turning it on again to continue its operation.
This machine should not be turned on until 3 minutes later after turning off
the power switch.
o
Locate Dispenser
1. Place dispenser upright.
2. Locate dispenser on a hard and level surface in a cool shaded location
near a grounded wall outlet.
Notice: DO NOT plug in power cord yet.
3. Position dispenser so the back is at least 20cm from wall and there are
at least 20cm of clearance on both sides.
Assemble
1. Remove drip tray from door and place the grid on top.
2. Snap drip tray and grid assembly into door.

6 7
E. TROUBLE SHOOTING
F. TECHNICAL PARAMETERS
MODEL: SP-A3T-UP
DIMENSION: 316*360*1040mm
RATED VOLTAGE:220V~240V RATED FREQUENCY:50Hz
RATED POWER:510W HEATING POWER:420W
HOT WATER: 90 4L/h COLE WATER: 10 2L/h≥℃ ≤℃
REFRIGERANT:R134a/45g RATED CURRENT:2.3A
COLD TANK CAPACITY:2L HOT TANK CAPACITY:1L
Water is leaking
Unplug dispenser, remove bottle and replace it.
No water is coming from the spout.
Make sure the bottle is not empty. If empty, replace it.
Make sure to completely depress the pushbutton controls.
Cold water is not cold
It takes up to one hour after setup to dispense cold water.
Make sure the power cord is properly connected to a working outlet.
Make sure the back of the dispenser is at least 20cm from a wall and
there is free airflow on all 20cm sides of the dispenser.
Make sure green power switch on back of dispenser is ON.
If water still isn’t cold, please ask for the service agent for assistance.
Hot water is not hot.
It takes 15-20 minutes after setup to dispense hot water.
Make sure the power cord is properly connected to a working outlet.
Make sure red power switch on back of dispenser in ON.
Nightlight is not working
Make sure the power cord is properly connected to a working outlet.
Make sure nightlight power switch on back of dispenser in ON.
Dispenser Is Noisy
Make sure the dispenser is positioned on a level surface.
H. CLEANING
G. CIRCUIT DIAGRAM
T2
Control panel
L
N
PE
S 5
S 4
S 3
Water pump
S 2
T 3
S 1
comp
Heater
T1
2. Rinsing instruction:Rinsing instruction:
Put the pumping pipe into the bottle.
Stop the bottle.
Push the bottle into the water drinking machine and close the door.
Turn on the power; let the machine pumped water then press the outlet
button.
Turn off the power and remove the water bottle.
Open the drain plug in back of the machine.
Screw up the drain plug after water drained and you can use the machine.
3. Draining instruction:
Draining instruction:
Open the hot water tap.
Open the outlet in back of the machine and drain the water.
After draining, cover the outlet and you can use the machine.
(Attention The drained water may be very hot, please operate it carefully.)：
4. Sanitizing:
Sanitizing:
Generally sanitizing should be done every 3 months (Exact time depends
on the machine working environment). About the sanitizing and cleaning
media use method please refer to the cleaning media use direction. You'd
better consult your service providers for the help.
1
2
3
4
5
6
7
1
2
3

8
I. MACHINE INSTALLATION
NOTE:
Manufacture shall have the right to make changes without prior notice.
To prevent the machine from swaying to fall,
please install the bracket accordingly.
1. Loosen the screw of the left or right bottom
angle just as the picture shown.
2. Use the screw to fix the bracket on the left or
right bottom angle of the water dispenser.
3. Make a hole on the floor s or the desk s
surface where the water dispenser will be
installed.
4. Fix the bracket on the floor by screw tightly.
5. Tighten the screw.
’’
Water dispenser
bracket
The hole for
tighten screws
123456
drilled hole