Vitec Multimedia FOCUS FS-H70 Instruction Manual

Frequently Asked Questions
FS-H70 / FS-H60 / FS-H50
v1.2

Inputs/Outputs ___________________________________________________________________________ 4
What are the inputs of each FS-Hxx Recorder? __________________________________________________________________ 4
Does the FS-Hxx Recorders support timecode? __________________________________________________________________ 4
Can the FS-H70 capture the embedded SDI timecode? ____________________________________________________________ 4
What are the supported input resolutions and frame rates supported for FS-Hxx? _____________________________________ 4
Below are the supported resolutions for each models:____________________________________________________________ 4
How can I verify the video input signal resolution and frame rate?__________________________________________________ 4
FS-H60 shows “NO AUDIO” on the unit menu with some HDMI sources, why? ________________________________________ 4
What is the purpose of the USB port? _________________________________________________________________________ 4
The LCD backlight is too bright, can I turn it off? _________________________________________________________________ 4
Recording _______________________________________________________________________________ 5
What type of files can be recorded? ___________________________________________________________________________ 5
Whatis the snapshot file type? _______________________________________________________________________________ 5
What are resolutions and bitrates of the recorded clips? __________________________________________________________ 5
What is the maximum continuous record time? _________________________________________________________________ 5
Can I record interlaced clips? _________________________________________________________________________________ 5
Where is the timecode information saved? _____________________________________________________________________ 5
My recording is split into 4GB file segments, why? _______________________________________________________________ 5
Can the recorder be externally triggered? ______________________________________________________________________ 6
Can I capture a snapshot while recording video or in stop mode?___________________________________________________ 6
How can I pause/resume a recording? _________________________________________________________________________ 6
Media __________________________________________________________________________________ 6
What type of media is supported on the FS-Hxx Recorders? _______________________________________________________ 6
What class of SDHC media card is recommended? _______________________________________________________________ 6
What is the maximal capacity of SDHC cards available? ___________________________________________________________ 6
What is the file format used on FS-Hxx Recorders? _______________________________________________________________ 6
Is it possible to know when the SDHC media card is reaching capacity? ______________________________________________ 6
Web interface / Connectivity ________________________________________________________________ 6
What features are available with the web interface? _____________________________________________________________ 6
The web interface allows to: _________________________________________________________________________________ 6
Can the FS-Hxx stream live video? ____________________________________________________________________________ 7
The live preview won’t start, why? ____________________________________________________________________________ 7
What is the main purpose of the stream? ______________________________________________________________________ 7

Can you preview the recorded clips? __________________________________________________________________________ 7
The live video preview shows 5 to 10 seconds latency, how can I reduce it? __________________________________________ 7
How can I connect to the FS-Hxx web interface? _________________________________________________________________ 8
I cannot connect to my FS-Hxx in AdHoc mode (direct connection)? _________________________________________________ 8
How do you configure the network settings? ___________________________________________________________________ 8
What are the default login and password for the web interface? ___________________________________________________ 8
Where can I find the IP address of my recorder? _________________________________________________________________ 8
I cannot connect to my FS-Hxx over Wi-Fi anymore. How can I reset the network configuration? _________________________ 8
I lost my credentials and cannot connect to the FS-Hxx web interface? How can I reset it? ______________________________ 9
Power __________________________________________________________________________________ 9
How long does the battery last? ______________________________________________________________________________ 9
How do you charge the battery and how much time does it take to charge? __________________________________________ 9
How do you preserve the battery life? _________________________________________________________________________ 9
Can the unit be powered externally? __________________________________________________________________________ 9
What is FS-Hxx power consumption? __________________________________________________________________________ 9
My camera/equipment has a Lemo 2 points or Hirose 4 points or D-Tap connector which allows to supply 12V voltage to an
external equipment. Can I tap the power supply for powering FS-Hxx? ______________________________________________ 9
How can I increase my recording time using the battery? _________________________________________________________ 9
Accessories _____________________________________________________________________________ 10
Can I purchase additional batteries? Are they compatible across the FS-Hxx models? _________________________________ 10
How can I mount the FS-Hxx onto a camera?___________________________________________________________________ 10
Can I use a non VITEC Wi-Fi adaptor with FS-Hxx?_______________________________________________________________ 10

Inputs/Outputs
What are the inputs of each FS-Hxx Recorder?
FS-H70 has an SDI input (BNC x1) which captures video and 2 embedded audio channel. This SDI input conforms to SPMTE259M (SD-
SDI) and SMPTE292M (HD-SDI). It also complies with SMPTE RP188 for SDI timecode capture.
FS-H60 provides a HDMI input (HDMI Type A x1) which captures video and 2 embedded audio channel (uncompressed).
FS-H50 provides a composite video input (BNC x1) and a stereo analog line level input (RCA x2).
Which FS-Hxx Recorders have a video/audio loopthrough?
FS-H70 and FS-H60 provides respectively a SDI and HDMI loopthrough (Audio/Video).
Does the FS-Hxx Recorders support timecode?
All the units can record timecode.
FS-H70 can capture the timecode from the SDI input signal:
FS-H50 / FS-H60 / FS-H70 recorders can record a timecode generated by the unit. The timecode is saved in the MOV timecode track
or in the XML attached to each recorded clip (start TC). MP4 clips do not embed timecode tracks.
Below are the modes available:
- EXT TC (only on FS-H70): the timecode is captured from the RP188 timecode located in the SD/HD-SDI input stream.
- FREE RUN: the timecode runs continuously even if the unit is not in record. Timecode between clips is not continuous.
- REC RUN: timecode runs only when the unit is in record. Timecode between clips is continuous.
- CLOCK SET (not available on FS-H70): the starting timecode is equal to the internal time clock of the unit.
NOTE: For FREE RUN and REC RUN modes, the device stores the last TIMECODE value when turned off. When turned on, the
TIMECODE continues from this last saved value. It is possible to reset the TIMECODE value by changing of TIMECODE mode.
Can the FS-H70 capture the embedded SDI timecode?
Yes. FS-H70 complies to SMPTE RP188 for SDI timecode capture.
What are the supported input resolutions and frame rates supported for FS-Hxx?
Below are the supported resolutions for each models:
Input Resolutions
FS-H50
FS-H60
FS-H70
1080 59.94p/50p
Yes
1080 59.94i/50i/29.97p/30p/25p/23.976p/24p
Yes
Yes
720 59.94p/60p/50p
Yes
Yes
PAL /NTSC
Yes
Yes
Yes
How can I verify the video input signal resolution and frame rate?
While in STOP mode, press and hold the OK button: the battery level will be displayed. Press OK again to display the video input
resolution detected. In the FS-Hxx web interface, the video input resolution is displayed in the header.
FS-H60 shows “NO AUDIO” on the unit menu with some HDMI sources, why?
The “NO AUDIO” message is displayed when FS-H60 does not detect any audio embedded in the HDMI signal. If your camera or
video source supports an audio signal, ensure that is a non-compressed format (such as Dolby, DTS, …).
FS-H60 supports PCM audio.
What is the purpose of the USB port?
The USB port is dedicated to the VITEC Wi-Fi adaptor only.
The LCD backlight is too bright, can I turn it off?
Yes. LCD and buttons backlight be adjusted in the Backlight menu or via the web interface.

Recording
What type of files can be recorded?
MOV, MP4 or TS (AVC HD) clips can be recorded.
A separate XML file and thumbnail is attached to each clip.
Where can I get some sample clips recorded with FS-Hxx?
Clips recorded at different profiles can be found here:
https://www.dropbox.com/sh/q3xwvlpm7mq5l9u/gqVhiAkeRf
Whatis the snapshot file type?
Snapshots are saved as JPEG files.
What are resolutions and bitrates of the recorded clips?
7 profiles are available ranging from 1080p30 8Mbit/s to 320x180 30 fps at 500kb/s.
Details of the profiles are documented in the user manual.
What is the maximum continuous record time?
In the table below, the maximum record times are listed using a 32GB SDHC card:
Profile
Recording resolution
Bit Rate
Duration
Premium
1080p
8Mb/s
8 Hours
High
720p
5Mb/s
13 Hours
Medium
960x540
3Mb/s
22 Hours
Standard
SD
1.5Mb/s
44 Hours
Light
320x180
0.5Mb/s
130 Hours
Can I record interlaced clips?
Yes. To record interlaced clips, AVCHD mode must be selected.
AVHD can record 1080i and PAL or NTSC clips.
Where is the timecode information saved?
The timecode is saved in the MOV timecode track or in the XML attached to each recorded clip (start TC). MP4 clips do not embed
timecode tracks.
My recording is split into 4GB file segments, why?
FS-Hxx writes files to a FAT32 volume which allows a maximum file size of 4GB. When this file limit is reached for a clip (1 hour of
recording in Premium –1080p), FS-Hxx automatically closes the file and creates a new clip. When putting clips in a playlist or in an
NLE, the combined clips will result in a perfectly continuous video (no frames are lost at clips boundaries).
Refer to the question below to know the duration of 4GB clip.
What is the video duration of a 4GB clip?
The clip duration is dependent of your profile. Please refer to the table below:
Profile
Recording resolution
Duration
Premium
1080p
1 Hour
High
720p
1H40
Medium
960x540
2H45
Standard
SD
5H30
Light
320x180
16H15

Can the recorder be externally triggered?
Yes, the FS-Hxx can be triggered externally via Wi-Fi.
Additionally, FS-H70 can be controlled using an SDI embedded record trigger from the camera (supported cameras : Sony /
Panasonic / ARRI) or by using the SDI timecode break.
The start/stop record mode can be set in the TRIGGER menu (onto the unit or using the web interface):
- NORMAL: Start/Stop recording can be triggered from the front panel REC button or via the web interface.
- EXTERNAL: FS-H70 receives Start and Stop record triggers from the ancillary data embedded in the SD/HD-SDI input stream. The
SDI a source must support Start/Stop command from the ancillary data.
- TC BREAK: FS-H70 monitors embedded timecode in the SD/HD-SDI input stream. The recording will begin when the timecode is
incrementing. When timecode stops, the recording stops.
Can I capture a snapshot while recording video or in stop mode?
Yes, hit the OK button (or the snapshot button in the web interface) and a snapshot will be saved.
How can I pause/resume a recording?
While recording, press long the REC button to pause a recording. To resume, press short the REC button. If STOP is needed after a
resume, press long the OK button.
What happens when the battery is running low or if the video input signal is lost while in recording?
The clip will be closed and saved onto the SDHC card.
In case the battery is running too low, the unit will then power down automatically.
Media
What type of media is supported on the FS-Hxx Recorders?
FS-Hxx can record onto an SDHC card.
What class of SDHC media card is recommended?
In practice, VITEC recommends a minimum class speed of 8.
What is the maximal capacity of SDHC cards available?
SDHC cards are available up to 32GB capacity.
What is the file format used on FS-Hxx Recorders?
FS-Hxx uses FAT32 file format. Maximum file size is 4GB.
Is it possible to know when the SDHC media card is reaching capacity?
Yes, using the web interface, the REC/STOP text in the header will turn RED if remaining free space onto the SDHC card is low
(<300MB)
Web interface / Connectivity
What features are available with the web interface?
The web interface allows to:
- Start/stop/pause remotely a recording
- Preview the live video input signal
- Review the recorded clips stored onto the SDHC card
- Download the recorded clips locally onto your PC/Mac
- Set the recording profiles and system parameters

Can the FS-Hxx stream live video?
Yes. The live input video can be accessed in the live window of the web interface. Click the “Live” button to start the preview.
If one wants to preview the stream using an external player, the live video link can be found in the same page. Below links can be
used too (IP_Address to be replaced by the FS-Hxx IP address:
For HLS : http://IP_Address/hls/preview.m3u8
For RTSP streams : rtsp://IP_Address/preview
The live preview won’t start, why?
First, verify that FS-Hxx does detect the input signal. In the web interface, a blue dot with the input resolution must be displayed.
Instead, if “No signal” is displayed, verify the video input source and its connections to FS-Hxx.
Second, for PC users, verify that VLC plugin is installed. If not, it can be found here for download:
http://download.videolan.org/pub/videolan/vlc/2.0.5/
Restart your web browser after install.
For MAC and iOS users, note that RTSP streams cannot be displayed within the web interface but VLC player can be used to view the
stream. HLS stream is optimized for such platform.
What is the main purpose of the stream?
The live stream is used for preview and confidence monitoring. It is a 480x360 at 30/25 frames per second allowing to be played
back on a large number of devices: tablets/cellphones/Mac/PC.
Can you preview the recorded clips?
Yes. It is possible to preview and download recorded clips (and snapshots) in the “Recorded contents” page of the web interface.
The live video preview shows 5 to 10 seconds latency, how can I reduce it?
By default, the live preview uses the HTTP Live Streaming (HLS) protocol. This protocol offers a wide platform compatibility
(iOS/Mac/Windows) and good quality of service but the latency is high.
In order to optimize the latency, switch to RTSP streaming protocol. However, in this mode, the live stream cannot be played back
within the default web interface using iOS and Mac platforms. VLC player can be used externally.
To set an optimal latency using VLC (any platforms):
-Open VLC application and open the Preference settings in “Tools” menu
-Select “Input & Codecs” tab
-Set default caching policy to “Low Latency” or “Lowest Latency” depending on your network performances.
Note: For experienced users, more settings are available by showing “All” settings (Input/Codecs menu, Advanced parameters)
VLC settings

How can I connect to the FS-Hxx web interface?
By default, FS-Hxx network is configured in AdHoc mode: FS-Hxx creates a Wi-Fi network called FS-Hxx-XXXX. To connect to this
network:
- Switch on the Wi-Fi on your PC / Mac or mobile device and search for the available networks.
- Select the network called FS-Hxx-XXXX to connect to it.
MAC PC iOS (iPhone/iPad/iPod)
- Once connected to the network, type in your web browser the address http://10.0.0.1 to access the web interface.
- By default, the web interface has no login/password, just leave blank the login/password text box and click the Login button.
I cannot connect to my FS-Hxx in AdHoc mode (direct connection)?
It is possible that the Wi-FI channel used by FS-Hxx Wi-FI adaptor is busy. It is possible to switch of channel by doing the following:
Go to the “Network Settings” menu then switch the Wi-Fi channel number. On next reboot, the Wi-Fi channel used will be different.
Important: No client must be connected to the FS-Hxx otherwise che channel change will not be applied on next reboot.
How do you configure the network settings?
Access the FS-Hxx web interface as indicated above and select the “System Preferences” page.
In the “Network Settings”, you can connect to an existing Wi-Fi network (protected or not) or change the network name of the
AdHoc network created by the FS-Hxx unit. Aplly the changes with the “Save Changes” button.
Settings will be applied on next reboot.
If the unit is not properly configured and access to the unit is no longer possible, refer to the “I cannot connect to my FS-Hxx over
Wi-Fi anymore. How can I reset the network configuration?” question below.
What are the default login and password for the web interface?
By default, login and password are empty. To access the web interface, just click the Login button.
Where can I find the IP address of my recorder?
You can find the IP address using the following shortcut: in STOP mode, press and hold the OK button: the battery level will be
displayed. Press the OK button three times to display the IP address.
Network settings can be found under the NETWORK menu.
I cannot connect to my FS-Hxx over Wi-Fi anymore. How can I reset the network configuration?
To restore the default network configuration, access the NETWORK SETTING menu and select RESET TO DEFAULT. On next reboot,
FS-Hxx-XXXX network will be available. Repeat steps from the “How can I connect to the FS-Hxx web interface?” question above to
connect to a private network.

I lost my credentials and cannot connect to the FS-Hxx web interface? How can I reset it?
Repeat the steps from the response above to reset your password. Note that your network configuration will also be reset
Power
How long does the battery last?
The battery will last approximately
-FS-H70: 3 hours with Wi-Fi ON, 5 hours without
-FS-H60: 5 hours with Wi-Fi ON, 8 hours without
-FS-H50: 6 hours with Wi-Fi ON, 9 hours without
What happens when the battery is running low?
When battery runs below 10%, a warning message is displayed on the unit. On the web interface, the battery icon will turn red.
When the battery gets too low, FS-Hxx will stop the recording, save the clip and shut down the unit automatically.
How do you charge the battery and how much time does it take to charge?
To charge the battery, FS-Hxx unit must be powered off. While powered on and connected to DC, FS-Hxx will not discharge the
battery at all.
A full battery charge takes about 3 hours.
How do you preserve the battery life?
The battery is a Lithium-Ion battery which does not require to be fully discharged to optimize its life. Store the battery in a
temperate area to maximize the battery life and performance.
Can the unit be powered externally?
Yes. FS-Hxx can be powered from the supplied AC-DC power adaptor (including international plug kit) or by an external DC source.
FS-Hxx requires a DC voltage between 5V and 17V. The lowest power consumption is achieved with a +12V powers supply.
What is FS-Hxx power consumption?
FS-Hxx power consumption is as followed:
-FS-H50: 1.5W without Wi-Fi dongle, 2.4W with Wi-Fi
-FS-H60: 2W without Wi-Fi dongle, 2.9W with Wi-Fi
-FS-H70: 3.4W without Wi-Fi dongle, 4.3W with Wi-Fi
My camera/equipment has a Lemo 2 points or Hirose 4 points or D-Tap connector which allows to supply 12V voltage to an
external equipment. Can I tap the power supply for powering FS-Hxx?
This is possible if the camera/equipment can provide a minimum of 0.5A.
Contact your sales representative to find the appropriate adaptor cable (no voltage conversion is required).
FS-Hxx features a 2.5mm DC Jack input.
How can I increase my recording time using the battery?
Here are some tips for maximum battery life / efficiency:
-If you are not using the web features, do not plug in the Wi-Fi USB adaptor.
Do not unplug the Wi-Fi adaptor while FS-Hxx is powered on.
-Reduce or turn off the LCD backlight
-Turn off the button backlight

Accessories
Can I purchase additional batteries? Are they compatible across the FS-Hxx models?
Yes, battery pack can be purchased separately. One battery is provided per unit. The battery is common to all units (FS-H70, FS-H60,
FS-H50). Do not use any third party battery to prevent damage to your unit.
How can I mount the FS-Hxx onto a camera?
FS-Hxx is shipped with a removable cradle. The cradle features a standard 1/4“-20 screw hole which fits several mountings
kit/adaptors available on the market.
Can I use a non VITEC Wi-Fi adaptor with FS-Hxx?
Only the VITEC Wi-Fi adaptor will work with FS-Hxx. The Wi-Fi adaptor is optimized for FS-Hxx in terms of performance and power
consumption.