Vitek STARLIGHT VTC-IRM30-2812 User manual

FEATURES:
• 1/2.8” Sony® STARVIS 2.1 MegaPixel CMOS Sensor
• 2.1 MegaPixel with Full 1080p/720p HD/EX-SDI 1.0, 2.0 / TVI / AHD / CVI
/ CVBS Output
• Advanced Starlight Technology Offers Dramatically Higher Sensitivity to Light
Producing Color Images in Very Dark & Night Scenes
• MegaPixel IR Corrected 2.8~12mm Motorized Varifocal Lens with 1 click
focus for easy Configuration
• 30 Dynamic Infrared LEDs at 850nm enable viewing in total darkness up to
100 feet
• Dual Glass Compartments to Eliminate IR Reflection
• 3D-DNR Digital Noise Reduction
• True Day/Night by ICR - Dual Filter Switch
• Fully programmable True WDR (Dual Scan)
• ROI (Region of Interest) WDR achieves superior exposure compensation
specifically in exact areas of interest while reducing HDD storage space
• Secondary Video Output & OSD Control Joystick are accessible inside a
gasket sealed removable side panel
• Advanced OSD Functions: Motion Detection, Privacy Mask, Defog, Sens-
up(~x32), Sharpness, Mirror/Flip, BLC/HLC, Deblur, Anti-Saturation, Title
Set, D-WDR
• 3-Axis mount with Simple One Turn Positioning Lock for Ease of Installation
• IP-67 Rated Water Resistance
• 12VDC / 24VAC Dual Voltage Operation
VTC-IRM30-2812
Premium 2.1 Megapixel Indoor/
Outdoor 6-in-1 HD/EX-SDI / TVI / AHD
/ CVI / CVBS Motorized Varifocal Bullet
Camera with IR LED Illumination
VITEK
VITEK

Safety Precaution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
To prevent electric shocks and risk of fire hazards, do NOT use other than
specific power source.
The symbol is intended to alert the user to the presence of important
operating and maintenance(servicing) instructions in the literature
accompanying the unit.
The symbol is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric shock to persons.
Warning :
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
Caution :
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Main power quality should be that of a typical commercial environment. If the user
of the model requires continued operation during power main interruption, it is
recommended that the model be powered from an uninterruptible power supply
(UPS).
2 3

Safety Precaution
NOTICE
The image used in this instruction manual are processed to help comprehension
and may differ from actual video of the camera.
Avoid installing in areas where shock or vibrations may occur.
Pay attention to safety when running the connection cable and observe that the cable
is not subjected to heavy loads, kinks or damage and no moisture can get in.
The warranty becomes void if repairs are undertaken by unauthorized persons.
Maintenance and repair have to be carried out only by authorized service centers.
Use only a mild detergent to clean the housing.
The camera should never be operated beyond the technical specifications.
This can lead to damage and void the warranty.
The camera should never be operated in water.
3

Contents
Safety Precaution
p.02~03
Contents
p.04
Composition
p.05
Dimensions
p.05
Installation Instructions
p.06~09
p.10~26
Operating Instructions
p.27
Specifications
4 5

Composition
Dimensions
Torque Wrench:
3mm (1pc)
Video Sub-out:
Cable (1pc)
Mounting Screw:
4 x 40mm (3pcs)
Plastic Anchor:
6 x 30mm (3pcs)
Mounting
Template
Operating
Instruction
Camera
3.17”
3.73” 3.43”
3.64”
9.72”
9.29”
5

Part Names
DUAL WINDOW
POWER
CABLE
SUNSHIELD BOLT
SUNSHIELD
FRONT CASE
OSD Setup
CONTROL COVER
BRACKET
REAR CASE
• Extreme care should be taken NOT to scratch the window in front of lens.
• Care should be taken that the cable is not damaged, kinked or exposed in
hazardous areas.
• Do not expose the camera directly to a strong light source such as the sun or
spotlight.
CAUTION
6 7

Installation Instructions
1. Locate the mounting template at the installation position and drill the ceiling
or wall if needed.
2. Route the Power cable to the connecting place.
3. Place the camera bracket on pre-drilled position and attach it using
mounting screws (4x40mm).
4. Set the camera’s viewing angle by using the L-wrench.
5. Put the sunshield onto the camera unit and tighten the sunshield-bolt.
Mounting Screw
: 4x40mm
■Adjustment of viewing angle
with one-touch 3-Axis bracket
Torque
wrench
Lock/Unlock
Screw
6 7

Installation Instructions
Pan & Tilt adjustments
1) Pan limit:
Pan is limited to +/- 90°.
3) Inclination limit
(Horizontal image alignment):
Inclination limited to +/-90° max.
2) Tilt limit:
Tilt is limited to 0°(2°) min ~ 90° max.
for wall(ceiling) installation respectively
with reference to the wall(ceiling) when
the inclination of camera module is 0°,
that is, the image is aligned horizontally.
90° 90°
• Unlock the screw on the camera bracket through using the torque wrench
supplied
• Set the camera’s viewing angle then lock the screw on the bracket.
90°
90°
±90°
•on the wall •on the ceiling
8 9

Installation Instructions
Installation Instructions
• Make sure power is removed before the installation.
• Follow the order for applying power:
Connect the power leads to the camera (observe polarity for DC power) then
plug-in power. This will avoid damage to the camera from power surges and
improper reseting .
Power Supply Connections
Camera can work with either 12VDC or 24VAC, dual voltage power. Primary
and secondary grounds are completely isolated to avoid the possible ground-loop
problems.
※SDI OUTPUT
(Yellow)
ANALOG OUTPUT
(Black)
POWER
(AC24V/DC12V)
▪ AC(-) :
AC24V/GND
▪AC(+) :
AC24V/DC12V
AC
(+)
AC
(-)
※Please use the cable as provided with camera. If camera cable is cut
and re-wired, the transmission distance of video can be reduced.
Especially SDI cable should not be cut because it requires detailed
wiring and affects the transmission distance.
8 9

Operating Instructions
Setup menu can be accessed and controlled by OSD control joystick on
the side of the camera. Five commands are available with the joy stick.
The design of OSD could be different according to the Model.
Using OSD Controller
Cover Open
Video Sub-out
Connector
OSD Control Joy Stick
SUB-OUT
ZOOM
1] SET Key (●) : Access to the menu or enter the setting.
To enter the main menu, press the Set Key down.
2] UP/DOWN Key (▲/▼) : Choose the desired sub-menu and to move
the cursor up or down.
3] LEFT/RIGHT Key (◄/►) : Set up the value of the selected menu. Used
to adjust the desired menu selection and to move the cursor left or right.
Description of the OSD control operation
Description of the Motorized ZOOM&FOCUS* adjustment
1) ▲: Zoom In
2) ▼ : Zoom Out
3) ◄: Focus Near
4) ► : Focus Far
(*) Works only when OSD Menu is inactive.
ANALOG OUT should be set to TVI MODE, AHD MODE or CVI MODE
to get CVBS video in sub-out. If it is set to CVBS, there is no CVBS video
in sub-out port. (SYSTEM> OUTPUT> ANALOG OUTPUT0)
If CVBS video is enabled through ANALOG OUT or Sub-out port, WDR
and 3D-NR functions are disabled in all video outputs.
It should be considered when installer adjusts the video with installation
monitor via CVBS video signal.
10 11

Operating Instructions
OSD menu Table
MENU SUB MENU CONFIGURATION
LENS
EXPOSURE
BACKLIGHT
DC
MANUAL
MODE (INDOOOR, OUTDOOR, DEBLUR)
0~20
WEIGHT
TARGET-BRT
MODE ROI WINDOW ZONE/USE,
H/V-POS, H/V-SIZE
NORMAL
OFF
HLC LEVEL, COLOR
H/V-POS, H/V-SIZE
BLC
WDR
LOW, MIDDLE, HIGH
LOW, MIDDLE, HIGH
COLOR
DAY & NIGHT
3D-NR
IMAGE
AWB
COLOR GAIN
EXTERN
AUTO
COLOR
B&W
SHARPNESS
SMART IR, ANTI-SAT., DELAY, IR LED CTL (AUTO, OFF)
SMART IR, ANTI-SAT., AGC THRES, AGC MARGIN, DELAY
SMART IR, ANTI-SAT.
AUTO, AUTOext, PRESET, MANUAL (C-TEMP, R/B-GAIN)
OFF, LOW, MIDDLE, HIGH
MAIN
OUTPUT
ANALOG
OUT0
ANALOG
OUT0
TVI MODE 0~10
TVI MODE, AHD MODE,
CVBS, CVI MODE
BRIGHTNESS
SHUTTER
SENS-UP
AGC
0~20
AUTO
MANUAL
(SPEED)
FLICKERLESS
0~10
OFF, x2, x4, x8, x16, x32
ZOOM / FOCUS AF MODE
SCANNING
MODE CHANGE
ONEPUSHAF
SYNC TDN
INITIAL ON
HALF, FULL
ENABLED, DISABLED
ON
ON, OFF
ZOOMPUSH, MANUAL
1/30(1/25), 1/60(1/50), 1/120(100), 1/250(200),
1/500(400), 1/1000(800), 1/2000(1600), 1/4000
(3200), 1/8000(6400), 1/15000(12800), 1/30000
(25600)
10 11

Operating Instructions
GAMMA 0.45, 0.55, 0.65, 0.75
OFF, ONMIRROR
DEFOG
D-WDR
MODE (AUTO, MANUAL)
LEVEL (LOW, MIDDLE, HIGH)
OFF, LOW, MIDDLE, HIGH
OFF, ON
OFF, ON
FLIP
MOTION OSD
TEXT ALARM
SYSTEM
EXIT
OUTPUT
RESOLUTION
TV SYSTEM
SAVE, CANCEL
CAM TITLE
RESET
LANGUAGE ENG, CHN(S), CHN, JPN, KOR, GER
OFF, ON
SDI OUTPUT
ANALOG OUT0
HD-SDI, EX-SDI 1.0, EX-SDI 2.0, OFF
TVI MODE, AHD MODE, CVBS, CVI MODE
1080 30P(25P), 720 30P(25P), 720 60P(50P)
US(NTSC), EU(PAL)
DET WINDOW
DET TONE
MDRECT FILL
SENSITIVITY
OFF, ON
OFF, ON
OFF, ON
0~10
0~4
WINDOW ZONE, WINDOW USE, DET
H/V-POS, DET H/V-SIZE
MOTION
OFF, RIGHT UP, LEFT DOWN
ON
PRIVACY ZONE NUM, ZONE DISP, H/V-POS, H/V-
SIZE, Y LEVEL, CB/CR LEVEL, TRANS
OFF, ON
IMAGE SHARPNESS MAIN
OUTPUT
ANALOG
OUT1
SDI
OUTPUT
ANALOG
OUT1
SDI&CVBS
SDI&CVBS
0~10
SDI OUT HD-SDI, EX-SDI 1.0,
EX-SDI 2.0, OFF
CVBS
0~10
ANALOG
OUT0
AHD MODE 0~10
CVI MODE 0~10
12 13

Operating Instructions
2-1. AF MODE
2. ZOOM/FOCUS
OSD menu Startup
• EXIT : Enters ‘EXIT’ menu with save current setting or without save.
• RETURN : Returns to the previous menu.
Press the ‘OSD menu SET key’ down to access the setup menu mode.
• ZOOMPUSH: Focusing works steadily for sharp focusing on the object.
In the case of a Motor driven lens, focusing resumes in about 7~8 seconds
to save the lens lifetime when the focus gets lost.
• MANUAL: Focusing can only be adjusted by ▲,▼ of OSD control joystick.
MENU V0. XX
1. LENS
2. ZOOM/FOCUS
3. EXPOSURE
4. BACKLIGHT
5. DAY&NIGHT
6. COLOR
7. 3D-NR
8. IMAGE
9. MOTION
A. SYSTEM
B. EXIT
OFF
EXTERN
MIDDLE
OFF
SAVE
DC
1. LENS
DC is for the best image when DC Auto iris lens is installed
1-1. DC
1-2. MANUAL MANUAL is for the best image when a Fixed lens is installed.
Lens can be selected either DC or MANUAL lens.
It should be selected according to lens type.
• INDOOR: Optimized for indoor environment.
• OUTDOOR: Optimized for outdoor environment.
• DEBLUR: If enabled it will reduce motion blur in certain indoor
environments but can cause more noise and color rolling.
• MODE : Selects MODE according to lighting condition.
13

Operating Instructions
2-2. MODE CHANGE
2-3. SCANNING
2-4. ONEPUSHAF
Focusing is activated only when zoom in/out is working.
MODE CHANGE is activated to set ZOOMPUSH in AF MODE.
It is for locking of the lens control to prevent undesirable operation.
Compensates for IR correction when the camera switches to DAY or NIGHT.
It is recommended to set OFF except specific conditions.
2-5. SYNC TDN
2-6. INITIAL
2. ZOOM/FOCUS
AF MODE
MODE CHANGE
SCANNING
ONEPUSHAF
SYNC TDN
INITIAL
RETURN
AF MODE Changes to MANUAL automatically
after 3 hrs when MODE CHANGE is ENABLED.
ZOOMPUSH
DISABLED
HALF
ON
OFF
ON
2. ZOOM/FOCUS
AF MODE
MODE CHANGE
SCANNING
ONEPUSHAF
SYNC TDN
INITIAL
RETURN
MANUAL
NOT USED
HALF
ON
OFF
ON
• ENABLED : Locks and disables the lens operation after 3 hours.
It is recommended to maintain the working-life of the motorized zoom lens.
• DISABLED : Disables the locking feature allowing lens operation at any time.
Lens initialization is necessary during the installation or the regular operation
to align the position data with the mechanical positions whose lens elements
may move and deviate from its calibrated position by shock or vibration,
for example, during transportation. Lens initialization is automatically
executed at power up.
INITIAL starts the lens initialization when pressing the joystick straight down
for about 2 sec. It is strongly recommended to execute LENS INIT in cases below;
- At the final step of installation.
- When focus becomes out of control by shock or vibration.
Lens scanning can be set to performs HALF or FULL on the screen.
Scanning checks the positions for zoom/focus at both of the end positions
and saves them for reference.
(Available only with AF MODE is ZOOMPUSH)
14 15

Operating Instructions
Adjusts the brightness of video (0~20).
3-1. BRIGHTNESS
A brighter video can be obtained by increasing the exposure time at
night with SENS-UP. It can be set to Off, x2, x4, x8, x16 or x32.
A higher setting will have a brighter video but more noise will be in the image.
3-3. SENS-UP
AGC(0~10) amplifies the video gain for brighter video but noise may occur.
3-4. AGC
3. EXPOSURE
BRIGHTNESS
SHUTTER
SENS-UP
AGC
RETURN
AUTO
X2
llllllllllllllllllllll
9
llllllllllllllllllllll
7
3-2-1. AUTO: Optimizes the video level by controlling the iris and the shutter
speed automatically.
3-2-3. FLICKERLESS : Flicker is used to remove the flickering on screen due to
differences in light and electric frequencies.
3. EXPOSURE
Select AUTO or MANUAL.
If shutter is set to Manual mode, SENS-UP mode is deactivated.
3-2. SHUTTER
3-2-2. MANUAL : 1/30(1/25), 1/60(1/50), 1/120(100), 1/250(200), 1/500(400),
1/1000(800), 1/2000(1600), 1/4000(3200), 1/8000(6400), 1/15000(12800),
1/30000(25600) Shutter can be set to fixed.
15

Operating Instructions
Cuts out the bright area with a mask and excludes it from compensation.
4-1. HLC (High Light Compensation)
4-1-1. LEVEL (0~20): Sets the HLC level. It determines the video level that starts
cutting out. Lower setting starts the cut out at a lower light level.
The cut out area is masked with selected color.
4-2-1. H-POS, V-POS :
Sets the position of BLC area to move vertically and horizontally.
4-2-2. H-SIZE, V-SIZE :
Sets the size of BLC area to move vertically and horizontally.
4-1-2. COLOR : Select mask color from 9 colors.
Black, White, Yellow, Cyan, Green, Magenta, Red, Blue and Customize.
llllllllllllllllllllll
10
HLC
LEVEL
COLOR
RETURN
BLK
BLC
H-POS
V-POS
H-SIZE
V-SIZE
RETURN
8
7
3
3
4-2. BLC (Backlight Compensation)
Compensates the video image by cutting out the bright areas with a mask or
adjusting the contrast of the video.
This function is used to brighten an image in the foreground with a bright
light area behind it such as sunlight, limiting the affect of silhouette.
BLC has a target window for compensation and its size and position can be
set by H-POS, V-POS, H-SIZE and V-SIZE.
4. BACKLIGHT
16 17

Operating Instructions
If CVBS video is enabled through ANALOG OUT or Sub-out port, WDR
and 3D-NR functions are disabled in all video outputs.
It should be considered when installer adjusts the video with installation
monitor via CVBS video signal.
4-3. WDR (Wide Dynamic Range)
4-3-1. MODE : Selects WDR mode normal or ROI setting.
• NORMAL: WDR function applies full screen.
• ROI (Region Of Interest) : Sets specific area of WDR by window setting.
Select window zone number from 0 to 3 and window use set to on.
Then the window zone can be modified for position and size.
When part of an image is extremely dark but another part is so bright you
can't see any details WDR will even the image out.
ROI
WINDOW ZONE
WINDOW USE
H-POS
V-POS
H-SIZE
V-SIZE
RETURN
0
ON
469
194
739
688
WDR
MODE
TARGET-BRT
WEIGHT
RETURN
ROI
MIDDLE
MIDDLE
4-3-3. WEIGHT : LOW, MIDDLE, HIGH
Selects the WDR value of the target area in MODE.
4-3-2. TARGET-BRT : LOW, MIDDLE, HIGH
Selects the brightness value of the target area in MODE.
16 17

Operating Instructions
5. DAY&NIGHT
SMART IR
ANTI-SAT.
DELAY
IR LED CTL
RETURN
ON
MIDDLE
AUTO
llllllllllllllllllllll
10
5. DAY & NIGHT
DAY/NIGHT is used to control the setting during day-time and night-time operation.
Select the mode according to the light condition and the camera types.
MENU V0. XX
1. LENS
2. ZOOM/FOCUS
3. EXPOSURE
4. BACKLIGHT
5. DAY&NIGHT
6. COLOR
7. 3D-NR
8. IMAGE
9. MOTION
A. SYSTEM
B. EXIT
OFF
EXTERN
MIDDLE
OFF
SAVE
DC
5-1-1. SMART IR
5-1. EXTERN
5-1-2. ANTI-SAT. (Available only with the SMART IR is ON)
5-1-3. DELAY
: D→N DELAY is time in seconds while camera maintains its status before
Day to Night switching. DELAY can avoid the unwanted/frivolous switching
by short term lights such as light from a passing car. Set delay term to
low, middle or high.
5-1-4. IR LED CTL
: IR LED Control(AUTO/OFF) is available with IR LED model only.
If it is set to OFF, IR LED will be turned OFF but DAY or NIGHT is still
determined by the built-in light photo sensor.
: Sets the anti saturation level 0~20. Setting high level avoids the saturation
but the corners will be darker accordingly.
: SMART IR can be set to reduce the saturation of strong IR illumination
at night in any menu of EXTERN, AUTO and B/W(NIGHT). Set to ON,
SMART IR is enabled and ANTI-SAT. level is controlled.
DAY or NIGHT is determined by the built-in light photo sensor for
cameras with built-in IR LEDS..
18 19

Operating Instructions
5. DAY&NIGHT
SMART IR
ANTI-SAT.
AGC THRES
AGC MARGIN
DELAY
RETURN
ON
MIDDLE
llllllllllllllllllllll
10
llllllllllllllllllllll
10
llllllllllllllllllllll
10
5-2. AUTO
Used when DAY or NIGHT is
determined by light level through
the lens and DAY from/to NIGHT
is switched automatically by the
scene brightness. It can be
controlled by the AGC threshold
level, AGC margin and delay time.
5-2-1. SMART IR
: SMART IR can be set to reduce the saturation of strong IR illumination
at night in any menu of EXT, AUTO and B/W(NIGHT). Set to ON,
SMART IR is enabled and ANTI-SAT. level is controlled.
5-2-3. AGC THRES
5-4. B/W
The camera is always in B/W mode.
Forcibly removes IR cut filter and switches to B/W regardless of light level.
5-2-2. ANTI-SAT. (Available only with the SMART IR is ON)
5-2-5. DELAY
: D→N DELAY is time in seconds while camera maintains its status before
Day to Night switching. DELAY can avoid the unwanted/frivolous switching
by a short term light such as light from a passing car. Set delay term
low, middle or high.
: Sets the anti saturation level 0~20. Setting high level of ANTI-SAT can
make the corners darker
5-3. COLOR
The camera is always in COLOR mode.
DAY/NIGHT is disabled and outputs color video.
:AGC(Auto Gain Control) is a threshold level which determines to switch
DAY from/to NIGHT in AUTO mode. Higher value makes the camera switch
DAY from/to NIGHT at brighter illumination.
5-2-4. AGC MARGIN
: Sets the gap level switching from/to DAY(color) or NIGHT(B/W).
18 19

Operating Instructions
6. COLOR
AWB
COLOR GAIN
RETURN
AUTO
llllllllllllllllllllll
10
6-1. AWB (Auto White Balance)
6-2. COLOR GAIN
6. COLOR
Automatically tracks the changes of color temperature and continuously
adjusts the white balance. AUTO, AUTOext, PRESET and MANUAL modes
are available.
Sets the color gain control level 0~20.
6-1-1. AUTO : Optimized for Indoor installation and compensates
AWB for low color temperature such as incandescent lights.
6-1-2. AUTOext : Optimized for outdoor sunlight applications and
compensates AWB for high color temperature such as sunlight.
6-1-3. PRESET : AWB is performed only whenever ● is pressed.
6-1-4. MANUAL : White balance is fixed to the settings by Color-Temperature
Red-GAIN and Blue-GAIN. It can be used only when the color temperature
does not vary.
20 21