Vitek VTC-TNT4RMAD User manual

VITEK
VITEK
VTC-TNT4RMAD
Transcendent Series 4 MegaPixel
Indoor/Outdoor WDR IP Active
Deterrence Motorized Turret Camera
QUICK START GUIDE
FEATURES:
• 1/3” 4.0 Megapixel CMOS Image Sensor
• Up to 30fps live view @ 4 MegaPixel (2592x1520)
• 2.8~12mm Motorized Varifocal Lens
• Alternate Flashing Red + Blue Warning Lights & User-Defined Warning / Command Voice Import
• Matrix IR with up to 165’ IR Range
• True Wide Dynamic Range (120dB)
• True Mechanical Day/Night function by ICR
• Triple Streaming: H.265+, H.264+ & MJPEG Compression
• XD-DNR (3D & 2D-DNR) Noise Reduction
• Backlight Compensation, Highlight Compensation, DeFog, Hardware Reset, ROI
• Advanced Analytics: Line Crossing Detection, Region Intrusion, Entrance / Exiting Detection
[All by Human / Vehicle Classification], Abnormal Video Signal Detection (Scene Change,
Video Cast & Video Blur)
• 1 Ch. Audio In + Built-in Mic + Built-in Speaker*
• 1 Ch. Alarm In + 1 Ch. Alarm Out
• Built-in MicroSD Card Slot for Local Recording (up to 256GB)
• Smart Alarm: Motion Det., Sensor Alarm, SD Card Error / Full, IP Address Conflict, Cable
Connection
• IP66 Weather Resistance
• Optional Junction Boxes (VT-TJB01, VT-TJB021), Wall Mounts (VT-TWM03, VT-TWMT-4)
and Pendant Mounts (VT-TPDM-2 [reqs. VT-TJB01], VT-TPDM-3 [reqs. VT-TJB021])
See other mounting options on page 9
• 12VDC & PoE (Power over Ethernet) Operation
*Please research local, state and federal laws regarding the implementation of audio surveillance.
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads
ACTIVE
DETERRENCE

2 3
Components and Accessories
Overview
First connect the Weather Resistant Cap to an Ethernet patch cable,
then connect the cameras ethernet adaptor. If not powering the
camera with PoE, also connect the power Cable to an approved
12VDC Power Supply.
Camera
Quick Guide
Screws
Drill Template
Plastic Plugs + Rubber Plug
Network Coupler
Weather Resistant Security Cap

3
Installation
Before beginning installation, make sure that the wall or ceiling is strong
enough to withstand 3 times the weight of the camera. The mounting
steps are as follows:
1. Attach the drill template to the
place where you want to install
the camera, then drill 3 screw
holes and 1 cable hole (if you
want to route the cables through
the mounting base) according to
the drill template (see below).
First Install a MicroSD Card as
Demonstrated in Diagram at Right
Connecting Alarm Input / Output
1.
2.
2.35”
1.17”
4.08”
.18”
5.15”
4.71”

4 5
2. Route and connect
relevant cables.
4. Loosen the fixed ring to adjust
the viewing angle of the camera.
Preview the camera’s image on a
monitor.
5. Tighten the lock screw to finish the installation.
3. Attach the mounting base to the wall with
the provided screw

5
LAN Configuration
The camera can be accessed on the local network either using the
IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool
1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.
vitekcctv.com/Downloads/Soft-
ware/Transcendent-IPTool_v2.0.2.zip
, then install on the PC. Open
the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201.
Click the information of the camera listed in the above table to show
the network information on the right side. Modify the IP address and
gateway of the camera and make sure its network address is in the
same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer
is 192.168.13.4. So the IP address of the
camera shall be changed to 192.168.13.X.
After modification, please input the password
of the administrator and click “Modify” button
to modify the setting.
** Default admin password: “123456".
MENU
IP Camera
N et wor k C a bl e N etwor k C a bl e
Switch
R outer C omputer