Vitek TRANSCENDENT VTD-TND4RMA4 User manual

VITEK
VITEK
QUICK START GUIDE
VTD-TND4RMA4
Transcendent Series 4 MegaPixel
Gen. IV Advanced A.I.
Motorized IP Vandal Dome Camera
FEATURES:
• 1/3” 4.0 Megapixel CMOS Image Sensor
• NDAA Compliant
• Up to 30fps live view @ 4 MegaPixel (2592x1520)
• 2.8~12mm Motorized Varifocal Lens
• Matrix IR (up to 165’ IR Range)
• True Wide Dynamic Range
• True Mechanical Day/Night function by ICR
• XD-DNR (3D & 2D-DNR) Noise Reduction
• Gen. IV Advanced Analytics: Regional Entrance / Exit Detection, Line Crossing,
Target Counting [All by Human / Motor Vehicle Classification] Face Detection, Object
Abandoned / Missing, Heat Map, Video Blur, Video Color Cast Detection, Abnormal
Video
• H.265+/H.265/H.264+/H.264/MJPEG
• 1 Ch. Audio In + 1 Ch. Audio Out + Built-in Mic*
• 1 Ch. Alarm Input + 1 Ch. Alarm Output
• CVBS Out
• Remote Viewing via CMS, Internet Explorer, iOS & Android Apps
• ONVIF Compliant
• MicroSD Card Slot for Local Recording (256GB)
• IP67 Weather Resistance + IK10
• Optional Junction Box (VT-TJB010), Wall Mount (VT-TWMT-A2 [reqs. VT-TJB010]),
Pendant Mount (VT-TPDMT-A2 [reqs. VT-TJB010]), and In-Ceiling Semi Flush
Mount (VT-TFMT-L2) Available
(see pg. 9 for additional mounting options)
• 12VDC & PoE (Power over Ethernet) Operation
*Please research local, state and federal laws regarding the implementation of audio surveillance.
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads
Also Available in Charcoal,
VTD-TND4RMA4B

2
Components and Accessories
Overview
Connect the Weather Resistant Cap to an Ethernet patch cable.
Connect the cameras ethernet adaptor. If not powering the camera
with PoE, also connect the power Cable to an approved 12VDC
Power supply.
Camera Quick start guide
Plastic plug ×4
Drill template
Rubber plug
4 tapping screws PA 4×2
1
3
4
5
6
2
ALARM
4 3 2 1
10
7
8
9
11
1 Ethernet Connector
2Audio Input (MIC)
3Audio Output (HP)
4CVBS Video Output
5 Alarm Input/Output
6DC12VPowerConnector
7 Zoom-
8 Zoom+
9 Micro SD Card Slot
10 Reset
11 DC IN & CVBS
Security cap
1- -A L M -C O M
2- -A L M - O P E N
3- - A L M -I N A
4- - A L M -G N D
D C 12 V
ALAR M
4 3 2 1
Allen Key
CVBS&DC
IN cables

3
Installation
Weather Resistant Network Coupler
1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.
Before beginning installation, make sure that the wall or ceiling is
strong enough to withstand 3 times the weight of the camera. The
mounting steps are as follows:
A lar m
P ower S our ce
IPC
A L A R M -C O M
A L A R M -O P E N
C onnecti ng A l ar m I nput/O utput
A lar m I nput
A lar m O utput
+
+
--
Sensor
IPC
A L A R M -I N
A L A R M -G N D
3
4
1
2
2. Loosen the screws to open
the lower dome and then
loosen the lock screw to
remove the mounting base.
1. Attach the drill template to
the place where you want to
install the camera, then drill
the screw holes and 1 cable
hole according to the drill
template.
1A. Rotate the trim ring counterclockwise to remove.
3.55”
3.55”
0.18”

4
6. Install the dome bubble on the camera with the included screws. Put
the trim ring back on the lower dome and turn it clockwise until it locks.
Finally, carefully remove the protective film from the bubble to complete.
4. Before adjusting the three-axis camera mount, preview the
camera on a monitor, then adjust as necessary to achieve the
optimum viewing angle.
3. Route the cables and
connect the power & video
cables, use the rubber plug
to fill the gap of the mounting
base. Then secure the
camera to the ceiling
or wall with the screws
provided.
5. Insert a MicroSD card if desired. Adjust the Zoom or Focus
to obtain an optimum image by pressing the T or W
buttons to adjust.

5
LAN Configuration
The camera can be accessed on the local network either using the
IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool
1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer at www.
vitekcctv.com/Downloads/Soft-
ware/Transcendent-IPTool_v2.0.2.zip , then install on the PC. Open
the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201.
Click the information of the camera listed in the above table to show
the network information on the right side. Modify the IP address and
gateway of the camera and make sure its network address is in the
same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer
is 192.168.13.4. So the IP address of the
camera shall be changed to 192.168.13.X.
After modification, please input the password
of the administrator and click “Modify” button
to modify the setting.
** Default admin password: “123456".
MENU
IP Camera
Network Cable Network Cable
Switch
Router Computer

6
4. Double-click the IP address and then the system will pop up the web
browser to connect IP-CAM . IE browser will download the Active X
control. After downloading, a login window will pop up as shown
below:
Input the user name and password to log in.
Default user name: admin / Default password: 123456.
Directly Access Through a Web Browser
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP: 80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for
the first time.
1. Manually set the IP address of the PC. The network segment should
be the same as the default settings of IP-CAM. Open the network
and share center. Click “Local Area Connection” to pop up the
following window.
Select “Properties” and then select Internet protocol according to the
actual situation (for example: IPV4). Next, click “Properties” button to
set the network of the PC.

7
2. Open the IE Browser and input the default address of IP-CAM and
confirm. The IE browser will download Active X control.
3. After downloading Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.
WAN Configuration
Access the camera by the router or virtual server for example.
1. Make sure the camera is connected to the LAN; Then log into the
camera via LAN and go to System Congfig→Network Config→Port
menu to set up the port number.
2. Enter System Config→Network Config→IP Address menu to modify
the IP address.
4. Open the web browser and input its WAN IP and HTTP port to
access the IP-CAM.
3. Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.
5. For additional setup, features and functions, please scan
the QR code on the front page of this quick guide and
download the complete manual.

8
Image Sensor
Image Size
Resolution
Min. Illumination
Lens
Day / Night
IR LEDs / IR Distance
Video Compression
Audio Compression
Main-Stream
Bit Rate / Type
Wide Dynamic Range (WDR)
Digital Noise Reduction (DNR)
Image Setting
Gen. IV Advanced Analytics
Smart Alarm
Region of Interest (ROI)
Network
Audio
Video Out
Alarm
Local Storage
Remote Viewing
Supported Browsers
Connection Protocol
Protection / Resistance
Power Input
Power Consumption 12VDC, PoE
Working Environment
Weight, Dimensions Dia × H
1/3” 4.0 Megapixel CMOS Image Sensor
4 MegaPixel (2592 × 1520)
4 MP(2592 × 1520) / 3 MP(2304 × 1296) / 1080P(1920 × 1080)
/ 720P(1280 × 720) / D1 / CIF(480 × 240)
0.005 [email protected], AGC ON; 0 lux with IR
Motorized 2.8-12mm
True Day/Night by ICR
3 Matrix / 165’
H.265+ / H.265 / H.264+ / H.264 / MJPEG
G.711A / G.711U
1~30fps: 4MP, 3MP, 1080P, 720P, D1, CIF, 480x240
64Kbps ~ 8Mbps / VBR, CBR
120dB Super WDR
XD-DNR (2D-DNR & 3D-DNR)
Saturation, Brightness, Contrast, WDR, Noise reduction
Regional Entrance / Exit Detection, Line Crossing, Target Counting [All by Human / Motor Vehicle Classification]
Face Detection, Object Abandoned / Missing, Heat Map, Video Blur, Video Color Cast Detection, Abnormal Video
Motion Alarm / Sensor Alarm
Each ROI to be Configured Separately
RJ45
1 In + 1 Ch. Audio Out + Built-in Mic*
1 Ch. CVBS Video Out
1 Ch. Alarm Input + 1 Ch. Alarm Output
MicroSD Card Slot (Up to 256GB)
CMS / Web Browser / Mobile (iOS/Android)
IE, Edge, Chrome and Safari (no plug-in required)
ONVIF
IP67 Weather Resistance + IK10 Impact
12VDC / PoE
350mA (LEDs Off) / 750mA (LEDs On), < 9W
-22° ~140° / < 95% Humidity
40.21 0z / 2.51 lbs. / 1140g, 5.91” × 4.49” (150 mm × 114 mm)
VTC-TND4RMA4 Detailed Specifications
*Please research local, state and federal laws regarding the implementation of audio
surveillance.

9
VT-TPLMT
Transcendent
Universal Pole Mount
VT-TCNMT
Transcendent Universal
Corner Mount
OPTIONAL ACCESSORIES
AND RELATED PRODUCTS
FOR VTD-TND4RMA4
VT-TJB010
Optional Junction
Box
VT-TPDMT-A2
Pendant Mount
- reqs. VT-
TJB010
VT-TFMT-L2
Optional Semi
Flush Mount
VT-TWMT-A2
Wall Mount -
reqs. VT-TJB010
5.48”
7.68”
5.47”
5.54”
5.48”
7.84”
9.17”
8.46”
6.43”
8.46”
8.47”

10
OPTIONAL ACCESSORIES AND
RELATED PRODUCTS FOR
NDAA COMPLIANT
TRANSCENDENT IP CAMERAS
NEWLYNEWLY UPDATEDUPDATED
• 8MP (4K) HDMI Output
• H.265S / H.265+ / H.265 / H.264 Video Compression
• Analytic Support Including Basic Face Detection,
License Plate Recognition, and More!
• Available in 4, 8, and 16 Channels
• Up to 24TB Depending on Model (12TB per HDD)
• PoE Support on ALL Models
Transcendent NVRs
A Standalone Solution with
Analytic Support and
NDAA Compliance!
VT-TNR414PN
VT-TNR818PN VT-TNR1626PN