Vitek VT-SMKB1 User manual

VITEK
4
VT-SMKB1
VT-SMKC1
Smoke Detector Camera
Product Manual
9970 GLENOAKS BLVD. UNIT B SUN VALLEY, CA 91352
PHONE: 888-VITEK-70 / 818-771-0300 FAX: [phone]
WWW.VITEKCCTV.COM | [e-mail]
Your new purchase from VITEK is guaranteed free defects in
materials and workmanship for a period of one your from the
date of purchase.
The product must have been used only for its intended purpose,
and not been subjected to damage by misuse, willful or
accidental damage, caused by excessive voltage
or lightning.
The product must have been installed in accordance with the
instructions given in the instruction manual and only
compatible equipment may be connected to it.
The product must not have been tampered with in any way then
the guarantee will be considered null and void.
Should the serial numbers be tampered with in any way then
the guarantee will be considered null and void.
This guarantee does not affect your statutory rights.
Contact VITEK directly for all servicing.
LIMITED LIABILITY WARRANTY
Before installing or operating the unit, please read this
manual thoroughly and retain it for your reference

2 3
Installation Steps
• 12VDC POWER INPUT IS NOT POLARITY PROTECTED
• Don't touch the CCD Chip with your fingers.
• Use the camera only with 12VDC power supply.
• Use a monitor with 75 ohm impedance.
1) Mount the camera securely.
2) Connect video using suitable coaxial cable with BNC-connector.
3) Connect the camera to a 12VDC power supply taking extreme care
to match the polarity, as the power input is not polarity protected.
Improper power connection is not covered by warranty.
Camera Specifications
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT OPEN OR REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
12VDC Power Input Is Not Polarity Protected.
Use extreme caution when connecting 12VDC power to unit.
Do not attempt to disassemble the camera.
To prevent electric shock, do not remove screws or cover. There are no user-
serviceable parts inside. Refer servicing to qualified service personnel.
Handle the camera with care.
Do not abuse the camera. Avoid striking or shaking it. The camera could be damaged
by improper handling or storage.
Do not expose the camera to rain or moisture, or try to operate it in wet areas.
Take immediate action if ever the camera does become wet. Turn power off and refer
servicing to qualified service personnel. Moisture can damage the camera and also
create the danger of electric shock.
Never face the camera toward the sun.
Whether the camera is in use or not, never face it toward the sun. Use caution when
operating the camera in the vicinity of spot lights or other blight lights and light
reflecting objects.
Do not operate the camera beyond its temperature, humidity or power source ratings.
Do not use the camera in an extreme environment where high temperature or high
humidity exist. Use the camera under conditions where temperatures are within
- 10°C ~ +50°C, and humidity is below 80% RH.
Do not touch the CCD sensor directly with your fingers.
If necessary, use soft cloth moistened with alcohol to wipe off the dust.
CAUTION
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
VT-SMKB1 VT-SMKC1
Image Device
Effective Pixels
Resolution
Minimum Illumination
S/N Ratio
Electronic Shutter
AGC
Sync. Mode
Scanning System
Gamma Correction
Horizontal Sync. Frequency
Vertical Sync. Frequency
Video Output
Power Source
Power Consumption
Operation Temperature
Standard Lens
Dimensions (W x H)
Weight
510 x 492
420 TV Lines
More Than 48dB
1/60 to 1/100,000 sec.
On
Internal Sync.
2:1 Interlace
0.45
15.734KHz
60Hz
Composite: 1.0 Vp-p / 75½Ω
12VDC
-10°~ 50°C (14°~ 122°F) Less Than 80% RH
f3.6mm (2.9 / 6 / 8 / 12mm Optional)
5.12" x 2.29" (130 x 58mm)
12.34 Oz. / 350 g. / 0.77 Lbs.
1/4" Color CCD
0.92 Lux / F1.4
3.6W
1/3" B/W CCD
0.2 Lux / F1.4
120mA