Vitrifrigo VFREE PLUS FP40 User manual

14 ENG
by VITRIFRIGO
INSTRUCTION MANUAL
THANK YOU FOR PURCHASING A VITRIFRIGO PRODUCT
ENG
PORTABLE
FRIDGES AND FREEZERS
VFP405060

15ENG
Index
1. SAFETY INSTRUCTIONS 14
2. PRODUCT FEATURES 18
3. PRODUCT STRUCTURE 18
4. INSTALLATION 19
5. FUNCTIONALITY AND OPERATION 19
6. BATTERY OPERATION 20
7. CARE AND MAINTENANCE 21
8. TROUBLESHOOTING 22
9. WARRANTY 23
10. TECHNICAL INFORMATION 23
11. SMART APP CONTROL 62
12. INFORMATION NOTE ON THE APP (13.01.2023) 64
UE DECLARATION OF CONFORMITY 68
PRODUCT IDENTIFICATION 69

16 ENG
1. SAFETY INSTRUCTIONS
WARNING: fire risk. The device contains refrigerant gas.
If in the fridge there is flammable gas,
you will find this label on the compressor.
In this case, some special precautions must be taken:
• Do not operate the appliance if it is visibly damaged.
• Do not block the gaps of the fridge with things like pin, wire, etc.
• Do not expose the appliance to rain or soak it in water.
• Do not place the appliance near naked flames or other heat sources (heaters, direct
sunlight, gas ovens etc.).
• Do not store any explosive substances like spray cans with a flammable propellant.
• Ensure the supply cord is dry and not trapped or damaged. Do not locate multiple
portable socket-outlets or portable power supplies at the rear of the appliance.
• Check the voltage specification on the type plate corresponds to that of the energy
supply. The appliance is only to be used with the power supply unit provided with the
appliance.
• Do not use electrical appliances inside the food storage compartments of the
appliance, unless they are of the type recommended by the manufacturer.
• Once unpacked and before turning on, the appliance must be placed on a level
surface for more than 6 hours.
• Make sure that the appliance stays horizontally when it is running. The tilt angle must
be less than 5° for long time running and be less than 45° for short time running.
• Keep the ventilation openings in the unit casing or in the built-in structure free of
obstacles.
• Keep the appliance stable on the ground or in the car; do not drain upside down.
DISPOSAL
• Do not throw away the packaging of your appliance but separate the materials
according to local waste disposal regulations.
• This product must not be thrown away with municipal waste but must be disposed
of as separate collection. Contact the Waste Electrical and Electronic
Equipment (WEEE) collection centers local to you or take it to a retailer
when purchasing a new equivalent appliance.
• The symbol to the side indicates that the fridge must not be disposed of
as urban waste.
• Improper disposal or incorrect use of the fridge is subject to administrative
and/or penalties imposed by current legislation.

17ENG
CAUTION!
• Repairs may only be carried out by qualified personnel. Incorrect repair may cause
danger. The lamp and supply cord must be replaced by the manufacturer or qualified
persons.
• Do not try to disassemble or modify the unit.
• The installation of DC power in the boat must be handled by qualified electricians.
• The appliance can only use our dedicated rechargeable batteries, non-rechargeable
batteries are prohibited, otherwise there may be a danger of fire and explosion.
• In use or during storage, battery found there has been high fever, leakage, odor,
distortion and other anomalies, please stop using it immediately and stay away from
the battery.
• Battery end of life should be immediately removed from the equipment, please
properly handle security of spent batteries, do not put into fire or water.
• Children shall not play with the appliance and relative packaging (plastic bag).
Cleaning and user maintenance shall not be made by children without supervision.
• The appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they’ve been given supervision or instruction concerning use of the
device in a safe way and understand the hazards.
• When used for drug cold storage, please review if the cooling capacity matches the
drug storage requirements.
NOTICE!
• Disconnect the power supply before each cleaning and maintenance and aer
every use.
• Do not use sharp tools to defrost; Do not damage the refrigerant circuit.
• Risk of child entrapment. Before you throw away your old fridge or freezer: take off the
doors: leave the shelves in place so that children may not easily climb inside.
• Check if the cooling capacity of the appliance is suitable for storing the food or
medicine. Food may only be stored in its original packaging or in suitable containers.
• If the appliance is le empty for long periods, switch off, defrost, clean, dry, and leave
the door open to prevent mould developing within the appliance.
• The appliance is intended to be used in household and similar applications such as:
- Staffkitchen areas in shops, offices and other working environments;

18 ENG
- Camping, Farm houses and by clients in hotels, motels and other residential
environments;
- Bed and breakfast type environments;
- Catering and similar non-retail applications.
• The appliance should be placed at dry place and prevent it from water splashing,
rain and moisture. Do not immerse into water.
• Do not place the appliance near heat sources such as heaters or direct sunlight.
• Information, illustrations and specifications in this manual reflect the most current
available at the time of publication, are subject to change without prior
notice. Please according to local regulations regarding disposal of the
appliance for its flammable refrigerant and blowing gas.
2. PRODUCT FEATURES
• High-efficiency DC compressor and conversion module.
• CFC free and great heat insulation.
• Intelligent battery protection system prevents your vehicle from running out of battery.
• LED display control panel for temperature setting, USB charging port: 5V/1A.
• Detachable lithium battery: 15600mAh/11.1V.
• Exterior design: bottle opener, telescoping handle, side handles, wheels.
• Interior design: built-in LED light, drain plug.
3. PRODUCT STRUCTURE
1 Door latch
2 Sealing strip
3 Control panel
4 Handle
5 Footpad
6 Cutting board
7 Bottle opener
8 Machine compartment
Note: The cutting board can be moved
by turning the knob on the top cover,
it is suggested to clean and dry it aer
every use.
1
2
3
4
5
6
7
8

19ENG
4. REVERSE DOOR OPENING DIRECTION
The door opening direction can be changed according to actual needs, please follow
the instructions below:
Door Disassembly:
Open the door
at a 90° angle
Take off the door
from one side
Take off the door
from the other side
Door Assembly:
Reverse the door
opening direction
Align the door sha with the
hole on one side and insert it
Fix the door on the other
side, installation finished
90°

20 ENG
5. FUNCTION AND OPERATION
1 Temperature Control 2 Led display 3 Set
4 ON/OFF 5 USB: 5V/1A
Power supply: connect to DC 12V/24V or AC 100~240V(using dedicated adapter) or solar
(12~50V) power supply.
Display Screen Initialization: when the fridge is powered on, the buzzer will make a long
beep, and the display will be on for two seconds then enter the standby mode.
Power On/Off: press to switch ON, long press for three seconds to switch OFF.
Temperature Setting: press or for temperature setting, the setting will be saved
automatically aer stopping operating for 4 seconds (Note: the temperature displayed is
the current temperature of the compartment, it’ll take a while to reach the set temperature.)
Temperature setting range: -20~20°C (-4~68°F)
Cooling Mode: under the running state, press to switch MAX (fast cooling) and ECO
(Energy saving Mode).(*Factory setting is MAX.)
Battery Protection Mode: under the running state, long press for three seconds until
screen flashes, then press again to select protection mode H(High), M(Medium) and
L(Low) (*Factory setting is H.)
Voltage Reference:
INPUT
MODE
DC 12V DC 24V
CUT OUT CUT IN CUT OUT CUT IN
L 8.5V 10.9V 21.3V 22.7V
M 10.1V 11.4V 22.3V 23.7V
H 11.1V 12.4V 24.3V 25.7V
* the voltage is theoretical value, there may be a deviation in different sceneries.
* H should be set when the product is connected to car power, and M or L should be set
when it is connected to a portable battery or other back-up battery.
Temperature Unit Setting: switch off the fridge, long press for 3 seconds until displays
E1, and switch to E5 by pressing again, then press or to switch Celsius or
Fahrenheit. (*Factory setting is °C.)
Reset: switch off the fridge, long press for 3 seconds until displays E1, under E1 mode,
long press at the same time for seconds to reset the settings.
-20
ECO MAX HML
°F°C
13.5
1 2 3
45

21ENG
• Recommended temperature for common food:
Drinks Fruits Vegetable Delicatessen Wine Ice cream Meat
5°C 5~8°C 3~10°C 4°C 10°C -10°C -18°C
41°F 41~46°F 37~50°F 39°F 50°F 14°F 0°F
6. BATTERY OPERATION
• Battery ON/OFF: long press the power button on the battery to switch ON/OFF. When
the battery is OFF, short press the power button to show current battery.
21
43
Model: FSAK-002
Capacity: 15600mAh/173Wh
Rated Voltage: 11.1V
Charging Limited Voltage(DC): 12.6V
Charging Limited Current(DC): 3A
1 - Power Indicator (Green: charging; Blue: discharging)
2 - Battery Indicator (show current battery)
3 - Power Button
4 - DC Charging Port
Warning: do not disassemble the battery!
• Battery charging (for reference only):
MODE 1
Charge in the fridge in standby mode
A - Wall outlet AC 100~240V
(using dedicated adapter, charging
time≈8h)
B - Car cigarette lighter DC 12/24V
(when the input voltage>13.5V, charging
time≈8h)
C - Solar 12~50V
Connect to the “SOLAR” port of the fridge
(When using 100W solar panel, charging
time≈5h)
MODE 2
Charge separately
D - Battery charger (optional)
Connect to the DC charging port of the
battery (Charging time≈8h)
E - Charging station (optional)
(Charging time of a single battery≈4h)
Note: It is suggested to switch off the
fridge when charging the battery
A
MODE 1
MODE 2
B
C
D
E

22 ENG
(the power supply may mainly power the compressor when the fridge is running).
When connect to a solar panel, please place the fridge in a cool place to dissipate heat.
The charging input power should be higher than the working power of the fridge (about
40-45W), or switch off the fridge, otherwise the battery will run out.
-> It is suggested to use 100W solar panel.
-> MAX Solar Input Voltage: 50V; MAX Solar Input Current:10A.
Note: the output of the solar panel is unstable, so it cannot power the fridge directly.
When using a solar panel, the battery should be put into the fridge.
• Discharging time (for reference only): In the low battery protection mode, the battery
can last about 4 hours aer being fully charged. When the temperature of the fridge is
set between 2~8°C (ambient temperature 25°C), it can last 12 hours aer the internal
temperature stabilizes. Remove or switch off the battery to prevent self-discharge when
not in use.
7. CARE AND MAINTENANCE
Cleaning:
• Switch off and unplug the device first to avoid electric shock.
• Remove the cover and drain from the hole at the bottom of the device.
• Use wet cloth to clean the device and dry it.
• Do not soak the fridge in water and do not wash it directly.
• Do not use abrasive cleaning agents during cleaning as these can damage the device.
Storage:
If the device will not be in use for a long time, please follow the instruction:
• Switch off and unplug the device.
• Take out all the items stored in the device.
• Wipe off excess water with a so rag.
• Put the device in a cool and dry place.
• Leave the lid slightly open to prevent odors from forming.
• Recommended storage environment:
ambient temperature: 25°C, ambient humidity: ≤ 75%.
Defrosting:
Humidity can form frost in the interior of the cooling device or on the evaporator.
This reduces the cooling capacity. Defrost the device in good time to avoid this.
• Switch off and unplug the device first to avoid electric shock.
• Take out all the items stored in the device.
• Keep the lid open.
• Wipe off the defrosted water.

23ENG
Never use hard or pointed tools to remove ice or to loosen objects which have frozen
in place.
8. TROUBLESHOOTING
Issues Cause/Suggestions
Fridge does not work
• Check if the switch is on.
• Check if the plug and socket are connected well.
• Check if the fuse has been burnt.
• Check if the power supply is malfunctioned.
• Switch on/off the fridge frequently may cause start delay of the compressor
Fridge compartments
are too warm
• The door is opened frequently.
• A large amount of warm or hot food was stored recently.
• The refrigerator has been disconnected for a long time.
Food is frozen • The temperature was set too low.
There is "water ow" noise
from inside the fridge
• It’s a normal phenomenon, caused by the flow of refrigerant.
There are waterdrops
around the fridge casing
or door gap
• It’s a normal phenomenon, the moisture will condense to water
when it touches a cold surface of the refrigerator.
The compressor is slightly
noisy when starting
• It’s a normal phenomenon, the noise will be reduced
aer the compressor works stably.
Code F1 displayed
• Possible cause: low voltage to fridge.
Adjust the battery protection from High to Medium or from Medium to Low.
Code F2 displayed
• Possible cause: condenser fan is overloaded. Disconnect power to fridge for
5 minutes & re-start. If the code shows again, contact manufacturer for service.
Code F3 displayed
• Possible cause: the compressor starts too frequently. Disconnect power to
fridge for 5 minutes & re-start. If the code shows again, contact manufacturer
for service.
Code F4 displayed
• Possible cause: compressor not kicking in. Disconnect power to fridge for 5
minutes & re-start. If the code shows again, contact manufacturer for service.
Code F5 displayed
• Possible cause: overheating of the compressor & electronics. Disconnect
power to fridge for 5 minutes & re-start. If the code shows again, contact
manufacturer for service.
Code F6 displayed
• Possible cause: no parameter can be detected by the controller. Disconnect
power to fridge for 5 minutes & re-start. If the code shows again, contact
manufacturer for service.
Code F7 or F8 displayed • Possible cause: temperature sensor is faulty. Contact manufacturer for service.
*For models with FSAK-002 detachable battery, if code F1 displayed, unplug or turn off the battery,
or connect to DC12/24V/AC100-240V(using the adapter) power supply to power the compressor
and battery in time to avoid long-term micro-current draining the battery.

24 ENG
9. WARRANTY
If the device gets malfunctional, limited warranty will be provided for 1 year from the date of
purchase, except following situations:
• Contrived damage.
• Damage caused by force majeure such as earthquake, conflagration, etc.
• Damage from inappropriate use or violating this instruction.
• Damage or malfunction caused by disassembling.
10.TECHNICAL INFORMATION
MODEL VFP40 VFP50 VFP60
RATED VOLTAGE DC12/24V or AC100~240V(using dedicated adapter) or Solar(12~50V)
RATED POWER 60W
CAPACITY 39.3 L/1.39 cu.. 49.1 L/1.73 cu.. 59 L/2.08 cu..
NOISE ≤45dB
TEMPERATURE
SETTING RANGE -20~20°C (-4~68°F)
CLIMATE
CATEGORY T/ST/N/SN
DIMENSIONS
(L*W*H)
647*400*441 mm
25 1/2 *15 3/4 *17 3/8 in
647*400*506 mm
25 1/2 *15 3/4 *19 15/16 in
647*400*571 mm
25 1/2 *15 3/4 *22 1/2 in
NET WEIGHT
(not including
battery)
14.5 kg /32 lb 15.7 kg /34.6 lb 16.7 kg /36.8 lb
*Due to product improvement, the technical information might be different from actual
information, please refer to the rating label on the product.
www.vitrifrigo.com

25ENG