Vive Comfort TP-P-605 Installation manual

Operation Manual Operation Manual

U.S. Registered Trademark. Patents pending
Copyright 2018 All Rights Reserved.
Table of Contents
Table of Contents
Thermostat Quick Reference
Thermostat Operation
Warranty Information
Page
2-4
5-6
7
1
Una version en español
de este manual se puede
descargar en la pagina web
de la compañia.
Equipment damage hazard.
Do not operate the cooling
system if the outdoor
temperature is below 50 ˚F
(10 ˚C) to prevent possible
compressor damage.
Caution:
Rev. 1821
TP-P-605
Vive Comfort
Toll Free : 888-776-1427
Web: www.vivecomfort.com
Hours of Operation: M-F 9AM - 6PM Eastern
P.O. Box 3377
Springeld, MO 65808-3377

FAN
ON AUTO
SYSTEM
COOL OFF HEAT
Program
Time
Hold/Run
Mon
Leave
Thermostat OperationThermostat Operation
LCD Display
Fan Switch
System Switch
See page 4 for details about
this display read out.
Select ON or AUTO. ON will
run the fan continuously.
AUTO will cycle the fan on
only when the heating or
cooling system is on.
Selects the operation mode
on your HVAC system.
Selecting HEAT turns on
the heat mode. Selecting
COOL turns on the air
conditioning mode.
Selecting OFF turns both
heating and cooling o.
When the battery icon appears replace your AA
batteries immediately. Failure to do so may result in your
heating & cooling system becoming inoperable. Freezing or
over heating can occur.
Caution:
User Buttons
Use these buttons to set up
your programming options.
Refer to the next page for
detail.
Temperature Setpoint Buttons
Press the + or - buttons to
select the desired room
temperature.
Fan Switch
System Switch
Temperature Setpoint Buttons
LCD Display
User Buttons
Easy Change Battery Door
See page 5 for details.
Easy change battery door

Thermostat Quick Reference Thermostat Quick Reference
The low battery indicator is displayed when the AA battery
power is low. If the user fails to replace the battery within 21
days, the screen will only show the low battery indicator but
maintain all functionality. If the user fails to replace the
batteries after an additional 21 days (days 22-42 since rst “low
battery”display) the set points will change to 55˚F(Heating) and
85˚F(Cooling). If the user adjusts these setpoints away from
these it will hold for 4 hours then return to either 55˚F or 85˚F.
After day 63 the batteries must be replaced immediately to
avoid freezing or overheating because the thermostat will shut
the unit o until the battery is changed.
Important:
Battery Door Information
Use the nger bevel on
the lower portion of the
thermostat to open the
easy access battery door.
Replace with
2 AA Alkaline
Batteries. High
quality Alkaline
batteries are
recommended.
Simple operating instructions are
found on the back of the battery door.
3
2
2
Indicates the current room temperature
Time and day of the week
Setpoint: Displays the user selectable setpoint temperature.
Hold is displayed when the thermostat program is permanently overridden.
System Operation Indicators: ON will display when the COOL
or HEAT is on. Compressor delay feature is active when ashing.
1
2
3
7
Low Battery Indicator: Replace batteries when this indicator is shown.
Program Time Periods: This thermostat has 4 programmable time periods
per day.
88
88
17

Thermostat Quick ReferenceThermostat Quick Reference
Temporary and Permanent Hold Feature Filter Change Reminder
If your HVAC contractor has congured the thermostat to
remind you when the air lter needs to be changed, you will see
FILT in the display when your air lter needs to be changed.
Resetting the lter change reminder: When FILT reminder is
displayed, you should change your air lter and reset the reminder
by holding down the second button from the top left side of the
thermostat for 3 seconds.
To reset the reminder rst enter the
lter change reminder setup by
pressing and holding down the
‘TIME’+ Hold/Run buttons at the same
time for 3 seconds. It rst shows you
the hours of run time the reminder is
set at. Then press the ‘Time’button
and it will show you the elapsed time
your fan has been running since the
last reset. At this point, press and
hold the Time and Hold/Run buttons
together for 3 seconds to reset elapsed
time and the reminder.
Note: This is a programmable thermostat, and will always be
running a programmed schedule. However, it can be overidden with
a Temporary or Permanent Hold.
Temporary Hold: With the system in Heat or Cool, anytime the set-at
temperature is changed with the + or - buttons, the thermostat will
enter a Temporary Hold. This will be indicated by“HOLD” ashing
below the set-at temperature and will remain in this hold until the
next programmed time period begins.
Permanent Hold: To enter a Permananet Hold, press the Hold/Run
button while “HOLD” is ashing. The word“HOLD” will remain on
continuosly, indicating a Permanent Hold.
To Return to Running Schedule: To manually exit this hold and
return to scheduled program, press Hold/Run button or cycle the
System Switch.
FAN
ON AUTO
SYSTEM
COOL OFF HEAT
Program
Time
Hold/Run
Mon
Leave