Vivitar Vivicam 20 User manual

Model :
- Quickstart Guide

11
CONTENTS
1. Camera Precautions ..................................................... 2
2. Vivicam Introduction ................................................... 3
3. Meet The ........................................................ 5
4. Ready To Pictures ................ 9
5. Installing Driver and Utility Software.......... 13
6. Transferring Pictures To Your Computer .................. 26
7. Using The as a PC Camera ......................... 30
Vivicam
...............................
Vivicam
Vivicam
Take

22
Follow these guidelines when using your :Vivicam
Keep camera away from the following:
-High temperatures and excessive humidity.
-Direct sunlight or other heat sources.
-Dust.
-Anywhere it will be subject to shaking.
Do not use camera outdoors if it is raining or snowing.
If the lens or the viewfinder becomes dirty, clean them
with a lens brush or soft, clean cloth. Never touch the
lens with your fingers.
If water or a foreign substance should get in the
camera, turn the camera off immediately and remove
the batteries.
Do not open the camera case or attempt your own
repairs. High-voltage internal components may create
risk of electrical shock or fire.
Do not open the battery compartment when the camera
power is on.
Transfer important images to your computer as soon
as possible to avoid losing image data.
1.Camera Precautions

33
2.1 Specification
Resolution choices :
Digital Camera mode : 640 x 480 pixels (VGA)
320 x 240 pixels (CIF)
PC Camera mode : 640 x 480 pixels
320 x 240 pixels
160 x 120 pixels
Focus : Standard mode : 0.9m to infinity from camera
Macro mode : 25cm ~ 30cm
24 bit full color
Memory : Built-in 8MB Flash memory
File Format : BMP
Flash Light : lnternal
Flash Light mode : Auto/Off
Self-timer : 10 seconds
Power : AA alkaline battery x 2
Interface : USB
Auto Power Off : Automatically turns power off if inactive for
about 60 seconds.
2. lntroductionVivicam

44
2.2 Accessories
1. Camera Cradle
2. Two AA alkaline batteries
3. Camera hand strap
4. Camera driver and utility software CD
5. USB cable
6. Camera pouch
7. Quickstart Guide
Quickstart
Guide

55
3.1 General Guide
Front
Back
3. Meet The Vivicam
Front
Back
Mode
Flash Light
Viewfinder
Self-Timer LED
Power On/Off
Select
Macro Mode
Standard Mode
Macro Switch
USB Connector
LCD panel
Lens
Shutter
Macro Mode LED
Busy LED
Viewfinder
Battery Compartment

66
A
3.2 LCD Panel lndicator
1
1
2
3
2
4
5
6
7 8 9
3
Picture Counter
:Total number of pictures you have captured
Continuous Capture
: Continuous capture mode
lmage Resolution
: 640 x 480 pixels (default setting)
: 320 x 240 pixels

77
4
5
7
6
Shooting Environment
: Outdoor 1 ( )
: Outdoor 2 (Sunny)
: lndoor 1 (Bright)
: lndoor 2 (Dark)
Memory Full
: Memory full icon
: Auto mode
: Off mode (default setting, no icon display)
Picture Delete
:
:
Cloudy, default setting
Flash Mode
Deletes all pictures
Deletes last picture

88
3.3 Camera Function Selection
Press Mode button to select the function you need.
The function icon on the LCD panel will blink. Press
Select button until you hear 2 beeps to confirm.
Function Mode Status
lmportant Note:
The camera will stop shooting function. Please
replace both batteries as soon as possible.
8
9
Self-timer
: Self-timer mode
Low Battery Warning
: This icon will appear, blinking and beeping,
indicating low battery power.

99
4. Ready To Take Pictures
4.1 Turning Power On
Power on : Press Power button and camera will
beep.
Power off : Press Power button again and camera will
beep.
(The camera will be automatically turned off
if inactive for about 60 seconds.)
4.2 Taking Pictures
Select focus mode (switch on left of camera body)
: Standard mode (0.9m ~ infinity)
Normal mode.
: Macro mode (25cm ~ 30cm)
For taking close-up pictures.
The Macro mode LED will light when switched to
this mode.
Press Shutter button to take picture and camera will
beep.
LCD Panel will show :
: Number of pictures you have taken.
: When memory is full, the icon will blink
and beep continuously.