Vivotek Camate CM80 Series User manual

Installation Guide
CM80 Series
Vari-Angle IR Illuminator
Rev. 1.1
QIG Part no.: 625040201G

2
Revision History:
* Rev. 1.0: Initial Release
* Rev. 1.1: Added safety instructions and warning messages.
Package Contents
X3
X1
X2
X2
• The wall-mount (CMA-B04), corner-mount (AM-412), pole-
mount adaptor (AM-311/312), and other brackets are separately
purchased.
• The screws and anchors for securing the illuminator to wall are
user-supplied. Apply M6 anchors or screws.
NOTE:
The 1/4" screws and washers are used to secure the illuminator
to an external camera housing.
• Please avoid eye exposure or apply appropriate protection, such as wearing a pair of Infrared
protection glasses, when working with the product. Always use camera live view to oberve IR
lighting effects.
WARNING:
• The luminaire should be positioned so that prolonged staring into the luminaire at a distance
closer than 2.5 m is not expected.
• Theexternalexiblecableorcordofthisluminairecannotbereplaced;ifthecordisdamaged,
the luminaire shall be destroyed.
• Thelightsourceofthisluminaireisnotreplaceable;whenthelightsourcereachesitsendoflife
the whole luminaire shall be replaced.
• Please make sure Reinforce/Double insulation shall be maintained between LV supply and control
circuits after installation.
• ThisoodlightshallbeusedwithaIEC/EN61347-2-13approvedLEDdriverwithSELVoutput
equaltoratedvoltageoftheluminaire,andoutputpowerofLEDdriversshallbeatleastequalto
rated power of the luminaire.
• Terminalblockisnotincluded.Installationmayrequireadvicefromaqualiedpersonnel.

3
• Do not install the product with unstable brackets, or installed on fragile mount surfces.
• This product shall be used in compliance with local laws and regulation.
• Please avoid using chemical oraerosolcleaninguidstocleantheproduct.Useacleancloth
slightly moistened with water.
• This product contains no parts repairable by the users. Contact CaMate for services.
• Power off the Illuminator as soon as smoke or unusual odors are detected.
• Do not place the Illuminator on unsteady surfaces.
• Replacing or failing to properly install the waterproof components, e.g., cables or cable glands,
willvoidourIP67warranty.
• Refer to your datasheet for the operating temperature.
• Do not touch the Illuminator during a lightning storm.
IMPORTANT:
Class III luminaires
Do not stare at the operating light source.
This marking indicates that this product should not be disposed with other household
wastesthroughouttheEU.Topreventpossibleharmtotheenvironmentorhumanhealth
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse
of material resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
RISK GROUP 3
WARNING IR emitted from this product,
Do not look at operating lamp.
IRilluminatorsRISKGRORP3/WARNINGIRemittedfromthisproduct./Avoideyeexposure.Use
appropriate shielding or eye protection. Do not look at operating lamp.

4
160mm(6.3")
220mm(8.7")
73mm(2.9")
103.8mm(4.1")
134.6mm(5.3")
61.5mm(2.4")
164.6mm(6.5")
59.5mm(2.3")
43mm(1.7")
43mm(1.7")
59mm(2.3")
32mm(1.3")
Mechanical Drawings
134
M6x1
4
64
29.3
8.2
30
82
Standard Small U bracket

5
Hardware Overview
I
Reserved mounting holes for
external camera housing
Ubracket
Waterproofcover
for angle selector
Optionalmountingpointsfor
Ubracket
Light sensor
Combo cable
Dehumidier
membrane
Reserved
Mounting holes
Unit Weight:2.1KG.
Max. Project Area:34684.7mm2.
160mm(6.3")
220mm(8.7")

6
Installation
II
U Bracket Positions & Orientation
UsetheincludedallenwrenchtoattachandadjusttheUbrackettoyourneedsattheinstallationsite.
It is highly recommended that the illuminator should be installed at a position higher than 3 meters from
the ground.
IMPORTANT:

7
35-Kg-cm
Beam angle
selector
Angle wider
Angle narrower
Longer distance
Shorter distance
Youmustrstsurveytheinstallationsiteanddeterminetheilluminationdistance.
Useacoinoratbladescrewdrivertoopenthewaterproofcoveratthebackoftheilluminator.
Usethe4mmsideoftheallenwrenchtoturnthebeamangletoanestimatedilluminationdistance,e.g.,
200meters.Seethetablesonthenextpageforhowtodoit.
You may forget your current beam angle
conguration. In this case, turn many full circles
clockwise until the rotation resistance is felt (returns
to the widest angle, reaches its mechanical stops),
and then turn the selector counter-clockwise
accordingtotheanglelistedonthetables.Eachfull
circle corresponds to a preset beam angle.
Tips:

8
CM80I8-1040
Rotate
direction
Full circle Beam angle Single mount Double mount Triple mount
Distance(m) Width(m) Distance(m) Width(m) Distance(m) Width(m)
0 40° 140 101.9 198.0 144.1 242.5 176.5
1 36° 150 97.5 212.1 137.9 259.8 168.8
2 30° 178 95.4 251.7 134.9 308.3 165.2
3 27° 192 92.2 271.5 130.4 332.6 159.7
4 24° 210 89.3 297.0 126.3 363.7 154.6
5 16° 288 81.0 407.3 114.5 498.8 140.2
6 15° 301 79.3 425.7 112.1 521.3 137.3
7 10° 350 61.2 495.0 86.6 606.2 106.1
Counter-clockwide
Narrower
Clockwide
Wider
CM80I8-2040
Rotate
direction
Full circle Beam angle Single mount Double mount Triple mount
Distance(m) Width(m) Distance(m) Width(m) Distance(m) Width(m)
0 40° 170 123.7 240.4 175.0 294.4 214.3
1 36° 175 113.7 247.5 160.8 303.1 197.0
2 29° 210 108.6 297.0 153.6 363.7 188.1
3 27° 221 106.1 312.5 150.1 382.8 183.8
4 20° 280 98.7 396.0 139.6 485.0 171.0
Counter-clockwide
Narrower
Clockwide
Wider
The factory default for the beam angle selector is always at the Widest angle.Whenyouturnthe
selector many rounds to its widest or the narrowest position, a rotation resistance can be felt. That
means the mechanical stop is reached, and you should not use more force.
RefertothetablesbelowforthecongurableIRlightbeam angles and the number of full circles
neededtochangetothepreferredbeamangles.Eachfullcirclecorrespondstoapresetbeamangle.
Forexample,ifyouneedtochangeCM80I8-1040'sbeamangleto30°(178m),turnthebeamangle
selector Counter-clockwise 2 full circles. If you are at the narrowest angle (10°) and prefer to turn to
24°,turn3fullcirclesclockwise.Whendone,installthewaterproofcover.
X2
Width
Distance
Angle
X2 30°36°
40°
Example:

9
CM80I8-4080
Rotate
direction
Full circle Beam angle Single mount Double mount Triple mount
Distance(m) Width(m) Distance(m) Width(m) Distance(m) Width(m)
0 80° 80 134.3 113.1 189.9 138.6 232.5
1 77° 83 132.0 117.4 186.7 143.8 228.7
2 74° 85 128.1 120.2 181.2 147.2 221.9
3 66° 89 115.6 125.9 163.5 154.2 200.2
4 63° 92 112.8 130.1 159.5 159.3 195.3
5 60° 95 109.7 134.4 155.1 164.5 190.0
6 55° 100 104.1 141.4 147.2 173.2 180.3
7 52° 105 102.4 148.5 144.8 181.9 177.4
8 50° 109 101.7 154.1 143.8 188.8 176.1
9 45° 115 95.3 162.6 134.7 199.2 165.0
10 40° 120 87.4 169.7 123.5 207.8 151.3
CM80I8-90120
Rotate
direction
Full circle Beam angle Single mount Double mount Triple mount
Distance(m) Width(m) Distance(m) Width(m) Distance(m) Width(m)
0 120° 60 207.8 84.9 293.9 103.9 360.0
1 105° 65 169.4 91.9 239.6 112.6 293.4
2 90° 70 140.0 99.0 198.0 121.2 242.5
Counter-clockwide
Narrower
Clockwide
Wider
Counter-clockwide
Narrower
Clockwide
Wider

10
Selectapositionattheinstallationsite.e.g.,underahangingroof.Youcanusethealignmentsticker
and start drilling a hole on the roof.
ApplytheincludedgripstickertotheUbracket.

11
M6 anchor
Hammertheanchorin(usersupplied,M6anchorsarerecommended).SecuretheUbrackettoit,such
as securing it using the bolt on a threaded pole.
Securetheilluminatortobracketusingthehexsocketscrews.

12
You will need to turn on both the partner camera and illuminator to precisely match the illuminated area
withthecamera'seldofview.Ifnecessary,adjustthebeamangleagain.
TurntheilluminatortowardtheFOVofthepartnercamera,shiftthetiltangle,andthentightenthe
screw and the rear cover to secure the illuminator.

13
Name Color Gauge Description
V+ Red (20AWG) Power input
12~24V DC±10%
24V AC±10% (50~60Hz), (14.5VDC current controlled)
V- Black (20AWG)
DI+ Green (26AWG) LEDON/OFFcontrol
* Dry contact
Logiclevel1(Open)=LEDoff
Logiclevel0(ClosetoGND)=LEDon
*Wetcontact
Logiclevel1:4V~40V=LEDoff
Logiclevel0:0.8VMAX=LEDon
DI- Yellow (26AWG) Ground
DO+ Purple (26AWG) Light sensor status output
1.Open=Day
2.Short=Night(300luxforIRON)
DO- Blue (26AWG) Ground
RS485+ Orange (26AWG) RS485interfacecontrol
RS485- Brown (26AWG)
Cable Pinouts

14
External
power source
Relay
NO NC
+3.3V+3.3V
R
R
R
GND GND GND
Switch
+3.3V
R
GND
Fuse/50mA
GND
Camera DI pins
DI+
DI-
DO+
DO-
Coordination with Cameras via the DI and DO Pins
IR LED ON/OFF control (Green & Yellow wires)
This mode means that CaMate illuminatorOn/Offcontrolistriggeredbycameraorotheralarmsystem.
Usercandecideusingtheappropriatedry/wetcontactsdependingonwiringcondition.
DI+:Green=TTL+voltage
DI-:Yellow=TTL–voltage(GND)
* Dry contact
Logiclevel1(Open)=LEDoff
Logiclevel0(ClosetoGND)=LEDon
*Wetcontact
Logic level 1: 4V~40V=LEDoff
Logiclevel0:0.8VMAX=LEDon

15
Light sensor status output (Purple & Blue wires)
ThismodemeansthatcameraDay/Nightmodeswitchingiscoordinatedwithandistriggeredbythe
illuminator'slightsensorviatheDO(Digitaloutput)connection(connectedtothecamera'sDIpins).
UserscancongurethecameracongurationtocontrolthecorrespondingilluminatorOn/Offstatus.
DO+:Purple=Opendrainoutput,45VMax.(currentmustbeunder100mA)
DO-:Bule=GND
Light sensor status output
1.Open=Day
2.Short=Night(lowerthan300luxforIRtoturnON)
Stand-alone illuminator mode
Thismodemeansthattheilluminator'sOn/Offcontrolistriggeredbyitslightsensor,inthecase,the
default wiring is connecting the green wire with purple wire.
Somecamerashaverelatedsettingsthatneedtheinter-connectionwiththeilluminator.Forexample,
somecamerascomewithanIRcutlterthatneedtobeturnedoffwhenenteringnightmode;or,
automaticallyturnontheadjacentilluminatorwhenenteringnightmode.

16
This page is intentionally left blank.