Vivotek FD8131V User manual

Quick Installation Guide
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
VIVOTEK INC.
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T:[phone]|F:[phone]|E:[email protected]
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686|F: 408-773-8298|E: [email protected]
All specications are subject to change without notice.
Copyright 2012 VIVOTEK INC. All rights reserved.
c
P/N:625018600G Rev. 1.0
FD8131V Fixed Dome
Network Camera
H.264 • Vandal-proof • IP66

EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Keep the Network Camera away
from water. If the Network Camera
becomes wet, power off immediately.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Refer to your user's manual for the
operating temperature.
Keep the Network Camera away from
direct sunlight.
Do not place the Network Camera in
high humidity environments.
Warning Before Installation
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
Replacing or failing to properly install
the waterproof components, e.g.,
cables or cable glands, will void our
IP65/66/67 warranty.

EN - 2
Software CD
FD8131V Alignment Sticker
D
r
i
l
l
h
o
l
e
Cable hole
Cable hole
Drill hole
RJ45 Female/Female Coupler /
Screwdriver/ Screws / Clamp Core
5
1
0
0
0
0
2
2
1
G
Package Contents
1
Quick Installation Guide / Warranty
Card
Physical Description
2
Lens
Reset Button
General I/O Terminal Block
Status LED
MicroSD/SDHC
Card Slot
Black Cover
Ethernet 10/100 RJ45 Plug
Power Cord Socket
Ground Wire

EN - 3
English
Hardware Installation
3
First, follow the instructions below to remove the dome cover.
Record the MAC address before
installing the camera.
Network Camera
Model No: FD8131V
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
RoHS
V I
MAC:0002D107258A
Tilt Adjustment Screw
Then remove the black cover as shown below.
Dome Cover

EN - 4
A
A
D
r
i
l
l
h
o
l
e
Cable hole
Cable hole
Drill hole
D
r
i
l
l
h
o
l
e
Cable hole
Cable hole
Drill hole
1. Attach the alignment sticker to the ceilling/wall.
2. Through the two circles on the sticker, drill two pilot holes into the ceilling/wall.
3. The Network Camera can be mounted with the cable routed through the ceiling/wall or
from the side. If you want to feed the cable through the ceiling/wall, drill a cable hole A
as shown in the above picture.
4. Hammer the supplied plastic anchors into the holes.
5. Align the two holes on each side of the camera base with the two plastic anchors on
the ceilling/wall, insert the supplied screws to corresponding holes and secure them
with a screwdriver.
Wall Mount
Ceiling Mount
6. Buckle the supplied clamp core onto the cable to prevent EMI radiation.
5 cm
The clamp core should be away
from the device at least 5 cm.

EN - 5
English
General Connection (without PoE)
Network Deployment
4
+ : Digital input
- : Digital input
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
2
3
Ethernet Switch
1
1. If you have external DI devices, make the connection from general I/O terminal block.
2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a
switch.
Use a Category 5 Cross Cable when Network Camera is directly connected to PC.
3. Connect the supplied power cable from the Network Camera to a power outlet.
Power over Ethernet (PoE)
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
PoE Switch
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via a
single Ethernet cable. Follow the below illustration to connect the Network Camera to a
PoE-enabled switch via Ethernet cable.

EN - 6
POWER C
OLLIS
ION
LINK
RECEIVE
PARTITION
12345
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
PoE Power Injector
(optional)
Non-PoE Switch
IMPORTANT:
Although the camera and the cable gland on the camera's end are waterproof, the cable
molding at the other end is not waterproof.
Measures should be taken to prevent water from leaking in through the cable-end molding,
such as the use of expanding foam sealant, putties, and so on. Note that the cable gland
on the camera should also be securely fastened to attain its waterproof functionality.
Waterproof Not Waterproof
Cable Molding

EN - 7
English
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is
analyzed, please click on the “Next” button to continue the program.
3. The program will search for all VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After a brief search, the main installer window will pop up. Double-click on the MAC
address that matches the one printed on the camera label or the S/N number on the
package box label to open a browser management session with the Network Camera.
Assigning an IP Address
5
For further setup, please refer to the user's manual on the software CD.
Ready to Use
6
1. A browser session with the Network Camera should prompt as shown below.
2. You should be able to see live video from your camera. You may also install the 32-
channel recording software from the software CD in a deployment consisting of multiple
cameras. For its installation details, please refer to its related documents.

EN - 8
Based on the live image retrieved from the camera, adjust the camera lens to the desired
viewing angle:
1. Turn the lens module left and right.
2. Loosen the tilt adjustment screws on both sides of the camera and then turn the lens
module up and down. Upon completion, tighten the screws.
3. Turn the lens to adjust the image orientation.
Adjusting the Lens
7
1
23
Loosen Tighten
Pan 350°
Rotate 340°
Tilt: 70°
The sophisticated 3-axis mechanism design offers very exible, easy hardware installation
for either ceiling or wall mount.
3-axis Mechanism Design
Pan 340°
Rotate 350°
Tilt Adjustment Screw
DO NOT over rotate the lens. Doing
so will damage the camera lens
module.
Tilt: 70°

EN - 9
English
1. Align the inner side of the black cover with
the notch on both sides of the lens, x the black cover.
2. If you choose to feed the cable through the ceiling/wall, arrange the cable neatly through
the cable hole. If you choose to feed the cable from the side, remove plate B.
3. Attach the dome cover to the camera as shown below. The dome cover cannot be
attatched if installed in the wrong orientation. Align the side cover (or side cutout) with
where the cable comes out from the camera. Push the dome cover to join with the
camera.
4. Finally, make sure all parts of the camera are securely installed.
Completion
8
1
B
3
2
Be aware of the
cable route!
W
8
T
N
To adjust the zoom factor and focus range
1. Loosen the zoom controller and then adjust zoom factor by moving the controller left
and right. Upon completion, tighten the zoom controller screw.
2. Loosen the focus controller and then adjust focus range by moving the controller left
and right. Upon completion, tighten the focus controller screw.