Vivotek IB8360-W User manual

Rev. 1.0
2MP • 12M IR • Smart Stream II • Video Rotation
WiFi • IP66 • UV Protection
User’s Manual
Wireless Bullet
Network Camera
IB8360-W
Rev. 1.0:

VIVOTEK
2 - User's Manual
Table of Contents
Overview ..............................................................................................................................................................3
Revision History ...............................................................................................................................................3
Read Before Use..............................................................................................................................................4
Package Contents ............................................................................................................................................4
Symbols and Statements in this Document......................................................................................................5
Physical Description .........................................................................................................................................5
Hardware Installation........................................................................................................................................7
Software Installation .......................................................................................................................................21
Ready to Use..................................................................................................................................................22
Accessing the Network Camera .................................................................................................................... 23
Using Web Browsers......................................................................................................................................23
Using RTSP Players.......................................................................................................................................26
Using 3GPP-compatible Mobile Devices........................................................................................................27
Using VIVOTEK Recording Software .............................................................................................................28
Main Page ...................................................................................................................................................... 29
Client Settings.................................................................................................................................................. 34
Conguration.................................................................................................................................................... 39
System > General settings .............................................................................................................................40
System > Homepage layout ..........................................................................................................................42
System > Logs ...............................................................................................................................................45
System > Parameters ....................................................................................................................................47
System > Maintenance...................................................................................................................................48
Media > Image .............................................................................................................................................52
Media > Video ................................................................................................................................................63
Media > Video ................................................................................................................................................64
Network > General settings............................................................................................................................72
Network > Streaming protocols ....................................................................................................................79
Network > SNMP (Simple Network Management Protocol)...........................................................................87
Network > FTP ...............................................................................................................................................88
Wireless > WLAN ...........................................................................................................................................89
Wireless > WPS .............................................................................................................................................91
Security > User accounts ...............................................................................................................................92
Security > HTTPS (Hypertext Transfer Protocol over SSL) .................................................................93
Security > Access List ................................................................................................................................100
PTZ > PTZ settings ......................................................................................................................................105
Event > Event settings..................................................................................................................................109
Applications > Motion detection....................................................................................................................123
Applications > Tampering detection .............................................................................................................126
Applications > Audio detection ...................................................................................................................127
Applications > Package management - a.k.a., VADP (VIVOTEK Application Development Platform) .......129
Recording > Recording settings ..................................................................................................................132
Local storage > SD card management.........................................................................................................137
Local storage > Content management .........................................................................................................138
Appendix ........................................................................................................................................................ 141

VIVOTEK
User's Manual - 3
URL Commands for the Network Camera................................................................................................141
Technical Specications ........................................................................................................................... 347
Technology License Notice.......................................................................................................................349
Electromagnetic Compatibility (EMC).......................................................................................................352
Overview
VIVOTEK’s IB8360 and IB8360-W (wireless) are stylish 2-megapixel mini outdoor bullet
network cameras, specifically designed for boutique retail applications. Delivering a
resolution of 1920x1080 at 30 fps, having IR illuminators effective up to 12 meters, and
including SNV technology for low light environments, these remarkable cameras provide
users with superior image quality around the clock.
When coupled with VIVOTEK’s Smart Stream II technology, the IB8360/IB8360-W can
reduce both bandwidth and storage consumption by up to 50%* while retaining the
same superb image quality as a Full HD camera. Built to withstand challenging weather
conditions, the IB8360/IB8360-W is armed with weather-proof IP66-rated housing to
withstand rain and dust, and ensure smooth operation.
VIVOTEK provides two easy-to-install options for this compact camera; the IB8360-W
boasts a 802.11b/g/n compatible wireless connection, and the IB8360 is designed for
Power over Ethernet (PoE) functionality. Both cameras were designed and constructed for
simple installation and easy connection.
* Depending on scene monitored.
Revision History
■ Rev. 1.0: Initial release.

VIVOTEK
4 - User's Manual
Read Before Use
The use of surveillance devices may be prohibited by law in your country. The Network Camera
is not only a high-performance web-ready camera but can also be part of a exible surveillance
system. It is the user’s responsibility to ensure that the operation of such devices is legal before
installing this unit for its intended use.
It is important to first verify that all contents received are complete according to the Package
Contents listed below. Take note of the warnings in the Quick Installation Guide before the Network
Camera is installed; then carefully read and follow the instructions in the Installation chapter to
avoid damage due to faulty assembly and installation. This also ensures the product is used
properly as intended.
The Network Camera is a network device and its use should be straightforward for those who
have basic networking knowledge. It is designed for various applications including video sharing,
general security/surveillance, etc. The Configuration chapter suggests ways to best utilize the
Network Camera and ensure proper operations. For creative and professional developers, the URL
Commands of the Network Camera section serves as a helpful reference to customizing existing
homepages or integrating with the current web server.
Package Contents
■ IP8360-W and camera stand
■ Screws and anchors
■ Power adaptor
■ Quick Installation Guide

VIVOTEK
User's Manual - 5
Symbols and Statements in this Document
i
INFORMATION: provides important messages or advices that might help prevent
inconvenient or problem situations.
NOTE: Notices provide guidance or advices that are related to the functional integrity of
the machine.
Tips: Tips are useful information that helps enhance or facilitae an installation, function,
or process.
WARNING: or IMPORTANT:: These statements indicate situations that can be
dangerous or hazardous to the machine or you.
Electrical Hazard: This statement appears when high voltage electrical hazards might
occur to an operator.
Physical Description
Front View
Rear View
Lens
MicroSD/SDHC/SDXC
Card slot
IR LED
Fastening ring
WPS / Reset / Restore
button
12V DC power cord
Status LED
Sun shield

VIVOTEK
6 - User's Manual
Dimension Drawing
74.98
163.73
98.33
NOTE:
• Use the camera only with a DC power supply that is UL listed, and limited power
source (LPS) certied. The power supply should bear the UL listed and LPS marks.
The power supply must also meet any safety and compliance requirements for the
country of use.
• When installing the camera, do not use excessive force.

VIVOTEK
User's Manual - 7
Hardware Installation
0002D10766AD
XXXXXX
1.Jot down the camera's MAC address for later reference.
< 10 kgf-cm
2.Find an appropriate position. Drill holes on the wall for the included plastic anchors.
Install the camera by driving screws through the mounting holes on the bracket. The
anchors may not be necessary if you install the camera on a wooden wall or calcium
silicate board. If preferred, drill a routing hole on the wall for routing the power cord.
If you need to route cables along the wall, use a pincer to remove the break-off tabs.

VIVOTEK
8 - User's Manual
4. Connect the included power adaptor between the camera and the power mains.
3.Install a MicroSD card if onboard storage is preferred. The card slot is accessed through
a rubber seal. Use a small Phillips screwdriver to open the seal.
Please properly fasten the seal and screw after the installation to ensure it is waterproof.
64GB
10
I
1

VIVOTEK
User's Manual - 9
IMPORTANT:
WPS Button Usage
Function LED Behavior
- White - operating in AP mode (default status).
Reset - press less than 3 seconds, Off then Red, then White.
WPS - press 3 to 5 secs, Flashing Blue for 2 mins, then Red, then Green.
Restore default - press longer than 7 secs. Flashing Red and Green
LED Color Indication
Steady Red Power on and system booting
All LED off Power off
Blink Red / Green every 0.15 sec Upgrading F/W
Blink Orange every 0.15 sec Restoring default
Blink Green every 1 sec Wireless AP linked
Blink Blue every 0.15 sec WPS searching
Blink White every 0.5 sec Operating in AP mode
Steady Red Network Failed
Blink Red / Green every 1 sec Connected to network
Refer to the functional description and LED denitions below when conguring the camera.
5.Connecting to network. There are 3 different ways to connect the camera to a wireless
network.
A-1
A: WPS
A-1. Press the WPS button for 3 to 5
seconds. You may need to use your
nger nail to press.
A-2. Press the WPS button on your
wireless AP (router). Some router/
AP have a virtual button on their
management software instead. Refer
to your AP's documentation for details
using its WPS function.
When WPS conguration is done,
wireless connectivity will be established
and the security encryption, such as
WEP or WPA-PSK, will be synchronized
with the AP. Install and use VIVOTEK's
IW2 utility to nd the camera. By default,
the camera's rmware uses the DHCP
client mode.
LED Denitions
WPS
AP
WEP or WPA-PSK
3 ~ 5secs
WPS

VIVOTEK
10 - User's Manual
NOTE:
1. WPS may not work if your AP is congured with a "hidden" SSID.
2. If no WPS-enabled AP is detected, the camera will repeat trying to connect by every 20
seconds. If the camera still can not detect an AP after 2 minutes, the wireless setup will
be cancelled.
3.If a camera is assigned with a fiex IP outside the AP's network segment, wireless
conguration will fail.
VIVOTEK (1C:CC)
AP mode
B-1
B: WiFi w/o WPS
Network Camera
Model No: XXXXXX
MAC: 0002D14BAD55
Pat. 6,930,709
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Made in Taiwan 4B:AD:55
MAC
Client mode
B-1. When your device has wireless connectivity, e.g., a notebook. Use it to connect
search and connect the camera. The camera comes using the AP mode as the default.
B-2. Search your wireless network. You should be able to nd the camera displayed as
"VVTK and the last 3 octets of the MAC address."
1
2
3
AP

VIVOTEK
User's Manual - 11
B-2 B-3
192.168.1.1
B-2. Select the camera and right-click to display the Connect button. Click to connect.
B-3. Open a web browser, enter the camera's default IP: 192.168.1.1.
B-4 B-5
6
B-4. The camera will search for the other APs within the network. Select an AP you prefer
your camera to connect to.
B-5. Enter the credentials for log in to your AP. Please move to Step 6.

VIVOTEK
12 - User's Manual
C:
C-1. You can also use your cell phone to connect the camera. Open your Wi-Fi setting
page.
C-2. You should be able to nd the camera displayed as "VVTK and the last 3 octets of the
MAC address." Identify the camera using its MAC address.
C-1 C-2
Network Camera
Model No: XXXXXX
MAC: 0002D14BAD55
Pat. 6,930,709
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Made in Taiwan
4B:AD:55
MAC

VIVOTEK
User's Manual - 13
C-3 192.168.1.1 C-4
C-3. Open a web browser window. Enter the camera's default IP: 192.168.1.1.
C-4. The camera will search for the other APs within the network. Select an AP you prefer
your camera to connect to.

VIVOTEK
14 - User's Manual
C-5
iViewer
C-6 C-7
C-5. Enter the credentials for log in to your AP.
C-6. When the camera is connected to an AP, it enters the client mode. You should then
install and open the iViewer utility from your app store.
C-7. Add the camera to your iView utility.

VIVOTEK
User's Manual - 15
C-8. You can click on Add from List. The iViewer will search within your current network for
the camera.
C-9. Once found, you can add the camera into your conguration. Please refer to the
documentation that came with iViewer for information.
C-8 C-9

VIVOTEK
16 - User's Manual
6.Open the Shepherd utility. The utility will search for cameras within the network.
7.Double-click on the camera to open a web console with the camera. You can now start
viewing the live stream.
Shepherd
Browser
LAN

VIVOTEK
User's Manual - 17
Forceful Password Conguration
The first time you log in to the camera, the firmware will prompt for a password
conguration for security concerns.
Enter the combination of alphabetic and numeric characters to fulll the password strength.
requirement. The default name for the camera administrator is “root”, and can not be
changed.
Some, but not all special ASCII characters are supported: !, $, %, -, ., @, ^, _, and ~.
You can use them in the password combination.

VIVOTEK
18 - User's Manual
Another prompt will request for the password you congured. Enter the password and then
you can start congure your camera and see the live view.

VIVOTEK
User's Manual - 19
SD/SDHC/SDXC Card Capacity
This network camera is compliant with SD/SDHC/SDXC 16GB / 8GB / 32GB / 64GB and
other preceding standard SD cards.
Internet connection via a router
Before setting up the Network Camera over the Internet, make sure you have a router and
follow the steps below.
1. Connect your Network Camera behind a router, the Internet environment is illustrated
below. Regarding how to obtain your IP address, please refer to Software Installation on
page 21 for details.
IP address : 192.168.0.3
Subnet mask : 255.255.255.0
Default router : 192.168.0.1
IP address : 192.168.0.2
Subnet mask : 255.255.255.0
Default router : 192.168.0.1
LAN (Local Area Network)
Router IP address : 192.168.0.1
WAN (Wide Area Network )
Router IP address : from ISP
Cable or DSL Modem
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
Internet
2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is
192.168.0.3, please forward the following ports for the Network Camera on the router.
■ HTTP port: default is 80
■ RTSP port: default is 554
■ RTP port for video: default is 5556
■ RTCP port for video: default is 5557
If you have changed the port numbers on the Network page, please open the ports
accordingly on your router. For information on how to forward ports on the router, please
refer to your router’s user’s manual.
3. Find out the public IP address of your router provided by your ISP (Internet Service
Provider).
Use the public IP and the secondary HTTP port to access the Network Camera from the
Internet. Please refer to Network Type on page 73 for details.
Internet connection with static IP
Choose this connection type if you are required to use a static IP for the Network Camera.
Please refer to LAN setting on page 72 for details.

VIVOTEK
20 - User's Manual
Congure the router, virtual server or rewall, so that the router can forward any data coming
into a pre-congured port number to a network camera on the private network, and allow data
from the camera to be transmitted to the outside of the network over the same path.
From Forward to
122.146.57.120:8000 192.168.2.10:80
122.146.57.120:8001 192.168.2.11:80
... ...
When properly congured, you can access a camera behind the router using the HTTP request
such as follows: http://122.146.57.120:8000
If you change the port numbers on the Network conguration page, please open the ports ac-
cordingly on your router. For example, you can open a management session with your router to
congure access through the router to the camera within your local network. Please consult your
network administrator for router conguration if you have troubles with the conguration.
For more information with network conguration options (such as that of streaming ports),
please refer to Conguration > Network Settings. VIVOTEK also provides the automatic port for-
warding feature as an NAT traversal function with the precondition that your router must support
the UPnP port forwarding feature.
Internet connection via PPPoE (Point-to-Point over Ethernet)
Choose this connection type if you are connected to the Internet via a DSL Line. Please refer to
PPPoE on page 73 for details.