Vogelzang International BX42E User manual

VGZ-005 / 20100616 BX42E / Page 1
Vogelzang International Corp.
READ ALL INSTRUCTIONS CARE-
FULLY BEFORE STARTING THE
INSTALLATION OR OPERATING
THE STOVE. FAILURE TO FOLLOW
INSTRUCTIONS MAY RESULT IN
P R O PE R T Y DA M AG E , B O D I LY
INJURY, OR EVEN DEATH.
SAFETY INSTRUCTIONS
SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIRE MAY
RESULT. FORYOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT PERMITS,
RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA.
READ ALL INSTRUCTIONS CAREFULLY.
1. The installation of this stove must comply
with your local building code rulings. Please
observe the clearances to combustibles (see
reference figures 1 & 2).
2. Do not install this stove in a mobile home,
manufactured home, trailer or tent
(NO EXCEPTIONS! per HUD Federal
Standard: 24 CFR Ch.XX).
3. Verify that the stove is properly installed
before firing the stove for the first time.
After reading these instructions, if you have
any doubt about your ability to complete
your installation properly, you must ob-
tain the services of a professional licensed
installer familiar with all aspects of safe
and correct installation. DO NOT use
temporary or makeshift compromises
during installation.
4. If any parts are missing or defective, please
notify the dealer or manufacturer immedi-
ately. DO NOT OPERATE A STOVE THAT
IS MISSING ANY PARTS!.
5. Do not tamper with combustion air control
beyond normal adjustment capacities.
6. Always connect this stove to a chimney and
vent to the outside. Never vent to another room
or inside a building. DO NOT CONNECT
THIS UNIT TO A CHIMNEY FLUE SERV-
ING ANOTHER APPLIANCE.
7. DO NOT CONNECT a wood burning stove
to an aluminum Type B gas vent. This is not
safe. Use approved masonry or a UL 103 HT
Listed Residential Type and Building Heat-
ing Appliance Chimney. Use a 6” diameter
chimney or larger, that is high enough to give
a good draft. (See specifics in installation
instructions).
8. Be sure that your chimney is safely con-
structed and in good repair. Have the chimney
inspected by the fire department or a qualified
inspector. Your insurance company should be
able to recommend a qualified inspector.
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
continued on next page
Deluxe BoxwooD stove
Model BX42E Owners Manual
(save this manual for future reference)
NOTE: THIS STOVE IS
NOT A UL LISTED STOVE.
DO NOT USE THIS STOVE IN A
MOBILE HOME, MANUFACTURED HOME,
TRAILER OR TENT – NO EXCEPTIONS!

Page 2 / BX42E VGZ-005 / 20100616
www.vogelzang.com
9. Creosote or soot may build up in the chimney
connector and chimney and cause a house/
building fire. Inspect the chimney connector
and chimney twice monthly during the heating
season and clean if necessary. (See Chimney
Maintenance, page 10).
10. In the event of a chimney fire, turn the air
control to closed position, leave the building
and CALL THE FIRE DEPARTMENT IM-
MEDIATELY! Have a clearly understood plan
on how to handle a chimney fire by contacting
your local fire authority for information on
proper procedures in the event of a chimney
fire.
11. To prevent injury, do not allow anyone to use
this stove who is unfamiliar with the correct
operation of the stove.
12. Do not operate stove while under the
influence of drugs or alcohol.
13. Ashes should not be allowed to accumulate
higher than the optional grate. Dispose of ashes
in a metal container with a tight fitting lid. Keep
the closed container on a noncombustible floor
or on the ground, well away from all combus-
tible materials. Keep the ashes in the closed
container until all cinders have thoroughly
cooled. The ashes may be buried in the ground
or picked up by a refuse collector.
14. The special paints used on your stove may
give off some smoke and an odor while
they are curing during the first 12 to 15 fires.
Additional smoke and odor may be emitted
from the light oils used in construction of the
fire box. This should disappear after a short
period of time and not occur again. Persons
with lung conditions or owners of susceptible
domestic pets (such as birds) should take
prudent precautions. Open windows and
doors as needed to clear smoke and/or odor.
Paint discoloration will occur if the stove is
overfired.
15. This stove has a painted surface which
is durable but it will not stand rough handling
or abuse. When installing your stove, use care
in handling. Clean with soap and warm water
when stove is NOT hot. Do not use any acids
or scouring soap, as these solvents wear and
dull the finish.
SAFETY INSTRUCTIONS continued…
16. While stove is in operation, all persons,
especially young children should be alerted to
the hazards from high surface temperatures.
Keep away from a hot stove to avoid burns or
clothing ignition.
17. If small children will be in the same room
as the stove during operation, provide a
sturdy barrier to keep them at a save distance
from the stove. NEvER LEAvE sMALL
CHILDREN uNsuPERvIsED when they
are in the same room as the stove.
18. Keep stove area clear and free from all
combustible materials, gasoline, and other
flammable vapors and liquids.
19. To prevent burns, always wear protective
clothing, leather hearth gloves and eye
protection, while tending the fire.
20. While in operation, keep the feed door closed
and secured at all times except while tending
the fire.
21. Do not overfire the stove. Overfiring will
occur if the feed door is left open during opera-
tion. Such actions can result in very dangerous
operating conditions.
22. All power cords and electrical appliances
and/or assemblies must be kept outside of the
clearance dimensions shown in this manual for
combustible materials.
23. For further information on using your stove
safely, obtain a copy of the National Fire
Protection Association (NFPA) publication,
“Using Coal and Wood Stoves Safely” NFPA
No. HS-10-1978. The address of the NFPA is
Batterymarch Park, Quincy, MA 02269.
NOTE: A PROFESSIONAL, LICENSED HEAT-
ING AND COOLING CONTRACTOR MUST
BE CONSULTED IF YOU HAVE QUESTIONS
REGARDING THE INSTALLATION OF THIS
SOLID FUEL BURNING APPLIANCE.

VGZ-005 / 20100616 BX42E / Page 3
Vogelzang International Corp.
ASSEMBLY INSTRUCTIONS
t o o l s r e q u i r e d
CAUTION: STOVE IS HEAVY. MAKE SURE YOU
HAVE ADEQUATE HELP AND USE PROPER
LIFTING TECHNIQUES WHENEVER MOVING
STOVE.
Refer to diagram and parts lists at back of this
manual.
1. Uncrate the stove and remove all packing ma-
terials and protective poly bag. (Save exterior
cardboard for further assembly.)
2. Remove parts from inside of stove. Parts
include: two lids (#9), one lid support (#10)
one damper collar (#12), one feed door (#6),
one lid lifter (#14), four legs (#1), hardware
pack (#15), and S-Hook (#16) from inside
the firebox.
3. Place flattened carton on floor and carefully
turn stove over onto carton.
m a t e r i a l s r e q u i r e d
(NOTE: The following items are NOT included with your stove)
4. Attach the rear legs to base of stove with stove
bolts.
5. Attach hearth to front of stove and attach the
front legs to hearth with stove bolts supplied.
6. Carefully lift stove upright and place in de-
sired location (see following instructions for
properly locating stove).
7. Attach damper collar to rear top surface of stove
using stove bolts.
8. Place lid support and two lids in position on
swing top.
9. Lower feed door into position while aligning
hinge pins.
10. Place S-Hook in hole at left front corner of
hearth. NOTE: S-Hook is used to hang lid lifter
while not in use.
1/8” dia. Drill Bit
(sheet metal screws)
Screwdrivers
(blade and Phillips types)
5/16” Nut Driver or Ratchet
with 5/16” Socket (for 1/4”
Hex Nuts)
11mm Nut Driver or
Ratchet with 11mm Socket
(for Stove Bolts)
Safety Glasses
Hearth Gloves
Pencil
6 foot Folding Rule or
Tape Measure
Tin Snips
Drill: Hand or Electric
Flooring Protection: 48” x 74”
as specified (see page 3)
Chimney Connection: 6” black
steel (24 ga. min.) straight or
elbow (as required)
1/2” Sheet Metal Screws
Chimney: Existing 6” Lined Ma-
sonry Chimney or 6”Inside Dia.
listed Type HT chimney.
Furnace Cement (manufacturer
recommends Rutland Code 78
or equivalent)
NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance
of your wood stove and assumes no responsibility of any incidental or consequential damages.
LOCATING STOVE
Proper clearances must be maintained for adequate
air circulation. Adequate ventilation must be
provided while operating this stove.
1. The stove must be placed on solid con-
crete, solid masonry, or when installed on a
combustible floor, on a listed floor protec-
tor, such as Hy-C or Imperial Model UL
4874BK or equivalent. The base must extend
at least 18” beyond the front of the door, 18”
to the sides of the stove, and must extend
under the stove pipe if it is elbowed towards
a wall (see figure 1 and consult local building
codes and fire protection ordinances.)
CAUTION: (FIRE HAZARD) CARPETING AND
OTHER COMBUSTIBLE MATERIAL MUST NOT
COVER THE FLOOR PROTECTOR. THESE
MATERIALS MUST REMAIN OUTSIDE OF
COMBUSTIBLE CLEARANCES, SEE FIG. 1- 2.
2. The stove must have its own flue. DO NOT
CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVING OTHER APPLIANCES.
3. After observing the clearances to combustible
materials (figure 1 & 2), locate your floor
protector accordingly (figure 1) and care-
fully place the stove in your selected location.
Install stove pipe, elbows, and thimble as
required, utilizing either a recently cleaned and
inspected 6” masonry chimney or a 6” i.d. listed
chimney. Maximum 64 square inches.
4. Use 6” round black stove pipe, not galvanized
stove pipe. Secure pipe sections with three (3)
sheet metal screws in each stove pipe and/or
elbow joint to firmly hold the pipe sections
together. DO NOT CONNECTTHIS STOVE
TO ANY AIR DISTRIBUTION OR DUCT
SYSTEM.
continued on next page

Page 4 / BX42E VGZ-005 / 20100616
www.vogelzang.com
5. Recheck clearances from the stove,
connector stove pipe, and corner clearances
using the illustrations (figure 1 & 2) and
your local building codes or fire protection
ordinances.
NOTE: Drywall faced with brick or stone must
be considered a combustible surface.
6. Do Not iNstall this stove iN a mobile
home, maNufactureD home, trailer or
teNt – NO EXCEPTIONS! (HUD Federal
Standard: 24 CFR Ch.XX)
7. The clearances provided are minimum
dimensions determined by the NFPA. Instal-
lation of this stove must comply with the
latest edition of NFPA 211 for reduced clear-
ances and/or your local building code rulings.
Use whichever minimum dimensions are
LARGEST.
Failure to follow these minimum clear-
ance requirements may result in an unsafe
installation and could cause a fire.
8. This stove is NOT a UL listed stove.
CAUTION: KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS AWAY FORM THE
STOVE.
Fig. 2 – Top View
Minimum Corner Clearances from
Combustible Surfaces
36"
36"
CORNER CLEARANCES
MINIMUM CLEARANCES
TO COMBUSTIBLE SURFACES
Unit to Sidewall ....................... 36 inches
Unit to Backwall ...................... 36 inches
Unit Corner to Wall .................. 36 inches
Pipe Connector to Backwall... 38 inches
Pipe Connector to Ceiling ...... 18 inches
ASSEMBLY INSTRUCTIONS continued…
Fig. 1 – Minimum Clearance Dimensions from Combustible Surfaces
COMBUSTIBLE
CONSTRUCTION
PER NFPA 211
FLOOR
PROTECTOR
DA SHED LINE SHOWS
HORIZONTAL CHIMNEY
CONNECTOR AND
ADDITIONAL FLOOR
PROTECTION REQUIRED
BACKWALL
48" (TOP VIEW)
36"
18"
18" 18"
38"
36" 74"
18"
SIDEWALL
COMBUSTIBLE
CONSTRUCTION
PER NFPA 211

VGZ-005 / 20100616 BX42E / Page 5
Vogelzang International Corp.
CONNECTOR PIPE INSTALLATION
Fig. 3 – Stovepipe/Flue Connections
CORRECT WRONG WRONG
1. The smooth end of the stovepipe fits over the
cast iron damper collar. Secure with three (3)
sheet metal screws.
2. Horizontal pipe runs must slope upwards
towards the chimney at least 1/4” per foot of
horizontal run.
3. You must have at least 18 inches of clearance
between any horizontal piping and the ceil-
ing.
4. The pipe cannot extend into the chimney flue
(figure 3).
5. Secure pipe/elbow sections with three (3) sheet
metal screws at each joint to make the piping
rigid.
6. It is recommended that no more than two (2)
90° bends be used in the stovepipe installa-
tion. The use of more than two 90° bends may
decrease the amount of draw and possibly
cause smoke spillage. Where possible, use only
corrugated (nonadjustable) elbows. These
provide a better seal.
7. The connector pipe must not pass through an
attic or roof space, closet, or any concealed
space, or floor, ceiling, wall or combustible
construction. A UL 103 HT Listed chimney
must be used from the first penetration of
ceiling or wall to the chimney cap. Never use
single wall connector pipe as a chimney - a
house fire could result.
NOTE: STOVE PIPE IS NOT INCLUDED.
TO PURCHASE PIPE, VISIT YOUR LOCAL
HARDWARE, HOME OR BUILDING CEN-
TER. SEE “LOCATING STOVE” PAGE 3 FOR
ADDITIONAL SPECIFICATIONS.

Page 6 / BX42E VGZ-005 / 20100616
www.vogelzang.com
CHIMNEY CONNECTIONS
The stove must be connected to either a ma-
sonry or manufactured metal chimney built and
tested to the specifications listed on the previous
pages.
Chimneys perform two functions:
1). As a means of exhausting smoke and flue
gases which are the result of fuel combustion.
2). The chimney provides “draft” which allows
oxygen to be continuously introduced into the
appliance, so that proper combustion is possible.
This stove relies on natural draft to operate.
NOTICE: Always provide a source of fresh air
into the room where the stove is located. Failure
to do so may result in air starvation of other fuel
burning appliances and the possible development
of hazardous conditions, fire or death.
Your stove itself does not create draft. Draft is
provided by the chimney. To achieve proper draft
your chimney must meet the three minimum height
requirements detailed in figures 4–7. A minimum
of 0.05 w.c. (measured in water column) is required
for proper drafting to prevent back puffing, smoke
spillage, and to maximize performance. (Gauges to
measure draft are readily available at stove stores
and are economical to rent or purchase.)
Factors such as wind, barometric pressure,
trees, terrain and chimney temperature can have
an adverse effect on the draft. The manufacturer
cannot be held responsible for external factors
leading to less than optimal drafting.
Should you have a problem with inadequate
draft, you should contact a licensed heating and
cooling contractor for assistance in solving the
problem.
IMPORTANT Installation Points
1. Size chimney flue to stove collar. This stove
requires a 6” diameter flue.
2. Never connect this unit to a chimney serv-
ing another appliance.
3. The chimney must meet all minimum
height requirements.
4. Never use a chimney to ventilate a cellar
or basement.
5. Contact your local building authority
for approved methods of installation and any
necessary permits and/or inspections.
MASONRY CHIMNEY
Before using an existing masonry chimney,
clean the chimney, inspect the flue liner and make
any repairs needed to be sure it is safe to use. Make
repairs before attaching the stove. The connec-
tor stove pipe and fittings you will need to con-
nect directly to a masonry chimney are shown in
figure 4.
Fig. 5 - Chimney Construction Through Attic Space
If the connector stove pipe must go through a
combustible wall before entering the masonry chim-
ney, consult a qualified mason or chimney dealer.
The installation must conform to local building and
fire codes and latest edition of NFPA 211.
If there is a cleanout opening in the base of the
chimney, close it tightly.
CHIMNEY
FLUE
5/8" TILE
CHIMNEY
LINER
MASONRY
CHIMNEY
THIMBLE
COLLAR
6˝ ROUND
24 ga. BLACK
CONNECTOR
STOVEPIPE
8˝ MIN.
LINER
BELOW
ENTRY
HOLE
Fig. 4 - Masonry Chimney Connection

VGZ-005 / 20100616 BX42E / Page 7
Vogelzang International Corp.
Fig. 6 - Chimney Construction Through Roof
Fig. 7 - Chimney Connection to Firebox
Through Masonry Wall
CHIMNEY CONNECTIONS continued …
MANUFACTURED CHIMNEY
REFER TO CHIMNEY AND CHIMNEY
CONNECTOR MAKER’S INSTRUCTIONS FOR
INSTALLATION AND USE.
Use only 6” diameter listed chimney UL 103
HT. Chimney made to this listing is High Tempera-
ture rated to 2100 degrees Fahrenheit. Use chimney
from only one manufacturer. Never mix brands.
Carefully follow the chimney manufacturer’s stated
requirements and clearances. Use the chimney
manufacturer’s attic guards, roof supports, flashing
and fire stops when passing through a ceiling. Use a
listed thimble when passing through a combustible
wall. Do not use makeshift compromises during
installation. Never use a single-wall connection
pipe as a chimney!
When using a pre-existing chimney, have it’s
condition and installation inspected before using.
Make sure that the chimney meets all of the UL
rating requirements listed above. Be aware that
not all manufactured chimney is of the UL 103
HT type.
NOTE: It is recommended that you contact a li-
censed heating and cooling contractor (consult your
local yellow pages) for chimney installation.
Manufactured chimney with the proper required
UL listing is available from most home centers,
hardware stores, and HVAC supply stores.
If you have access to the internet, you may
wish to view chimney manufacturers’ informa-
tion on-line. See, www.duravent.com, www.
selkirkinc.com, or www.mtlfab.com.
VENTING TO EXISTING FIREPLACE
In some instances, people desire to convert an
existing fireplace for stove use. Usually, safe con-
nection to an existing masonry chimney requires
more work than using a prefabricated chimney.
The existing fireplace must be closed and sealed at
the damper with high-temperature caulk, ceramic
wool, or furnace cement. Prior to installation, clean
and inspect the existing flue and smoke shelf. In-
stallation should be designed so the system can be
dismantled for periodic cleaning and inspection.
Before conversion, make sure the existing chimney
is structurally sound, the chimney incorporates a
flue liner and make sure it is in good condition.
(A flue liner consists of clay tile that protects the
brickwork of a chimney. If a chimney does not
have a liner, or it is damaged, have it relined by
a professional. DO NOT USE a chimney that is
unlined or damaged!) If you have any question
regarding the condition of the chimney, consult a
qualified licensed contractor, qualified engineer,
competent mason, certified Chimney Sweep, or a
knowledgable inspector. Consult your insurance
company if you cannot find a qualified expert.

Page 8 / BX42E VGZ-005 / 20100616
www.vogelzang.com
CHIMNEY CONNECTIONS continued …
Fig. 8 - Fireplace Conversion
CAUTION: Not all fireplaces are suitable
for conversion to a wood stove. Check
with a qualified expert.
Many prefabricated fireplaces are of the
“zero-clearance fireplace” category. These consist
of multilayered metal construction. They are de-
signed with enough insulation and/or air cooling
on the base, back and sides so they can be safely
installed in direct contact with combustible floors
and walls. Although many prefabricated fireplaces
carry endorsements from nationally recognized
organizations for use as fireplaces, they have not
been tested for connection to wood stove heaters.
Connecting a stove to such a device will void the
manufacturer’s warranty.
Steel-lined fireplaces are constructed with
1/4” firebox liner, an air chamber in connection
with 8” of masonry. These can be safely used with
wood burning stoves. They contain all the essential
components of a fireplace, firebox, damper, throat,
smoke shelf, and smoke chamber. Many look iden-
tical to masonry fireplaces and should be checked
carefully before connecting a stove to them.
Venting a stove directly into a fireplace does
not meet code and should not be attempted. (This
constitutes connection to another appliance - the
fireplace.) Combustion products will be deposited
and build up in the firebox or fireplace. The stove
warranty will be void with such an installation. Do
not create a hazard in your home by connecting in
this manner.
FIREPLACE INSTALLATION
Directly connecting the stovepipe into the exist-
ing masonry chimney (figure 12 “Type A” fireplace
conversion) of the fireplace is the only approved
method of installation. This is a complicated and
involved process and to insure safety should only
by done by a qualified installer.
1. An entry hole must be cut through the masonry
and tile liner with minimal damage to the liner.
At least 8” of liner must remain below the entry
position. When locating the stove and stove-
pipe, all minimum clearances must be observed
from combustible surfaces including mantels,
combustible trimwork, ceilings and walls.
Positioning the center of the stove pipe entry
into the chimney 24” below the ceiling should
insure proper clearance for a 6” stovepipe.
2. Install a metal or fire clay (5/8” minimum thick-
ness) thimble. Make sure the thimble is flush
with the inner surface of the chimney liner and
does not protrude into the flue (see figure 4 on
page 6).
3. Secure the thimble with refractory mortar. The
thimble should be surrounded by 8” of solid
unit masonry brickwork or 24” of stone.
4. Install the stovepipe into the thimble as far as
possible without extending past the flue lining
(see figures 4 on page 6).
5. A small airspace (about 1/2”) should remain
between the stovepipe and thimble to allow for
expansion of the pipe. Seal this airspace with
high-temperature caulking or ceramic wool.
6. Secure and seal the damper in the closed posi-
tion using high-temp caulking, ceramic wool,
or furnace cement. Also check to see if the
chimney has a cleanout. If it does, make sure it
is closed and sealed as well. A leaky cleanout
will greatly reduce draft efficiency.
If you have any questions regarding venting
your stove, contact the manufacturer or contact
the National Fire Protection Association (NFPA)
and request a copy of the latest editions of NFPA
Standard 211 and NFPA Standard 908. Their ad-
dress is:
Battery March Park, Quincy, MA 02269.

VGZ-005 / 20100616 BX42E / Page 9
Vogelzang International Corp.
OPERATING INSTRUCTIONS
This stove is designed to burn
WOOD FUEL ONLY.
Hardwood, 20” to 24” should be split and air
dried (seasoned), for 6 months to obtain maximum
burning efficiency. Wood should be stored in a dry,
well ventilated area.
NOTICE: USE SOLID WOOD MATERIALS ONLY.
DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS. DO NOT USE COAL AS COAL OR
CHARCOAL WILL DESTROY THE GRATE AND/
OR THE FIREBOX.
NOTE:A 2”layer ofsandora layeroffirebrick
should be used as bottom insulation in the
Boxwood stove. An optional cast iron grate,
42G, may be used instead of firebrick or
sand. See Accessory Sheet included with
this manual for ordering information.
LIGHTING
1. Open draft damper fully to provide maximum
draft.
2. Open the feed door and place several wads of
crushed paper in the firebox.
3. Lay small stacks of kindling on the paper to
start the fire.
4. Light the paper and kindling, close the door
and secure tightly.
5. Add fuel after fire is burning briskly. Use care
not to smother the kindling fire when adding
wood. Close the door and secure tightly.
6. Adjust the draft damper and spin draft
control. The more closed the spin draft is set,
the lower and slower the fire will burn. The
more open, the faster and hotter the fire will
burn. Do not overfire the stove.
ADDING FUEL
Add small amounts of fuel each hour or so
instead of piling large quantities of fuel at one
time. This will insure a more complete combustion
process and less buildup of tars, soot, or creosote
will occur in the chimney.
1. Always open draft damper before opening the
feed door.
continued on next page
CAUTION: HOUSE FIRE HAZARDS
• DonotstorewooDonfloorprotec-
TOR, UNDERNEATH STOVEPIPE OR ANY-
WHEREWITHIN MINIMUM CLEARANCES FROM
COMBUSTIBLE SURFACES SPECIFIED FOR
THIS STOVE.
• overfiring may cause a house fire.
YOU ARE OVER FIRING IF THE STOVE OR
CHIMNEY CONNECTOR GLOWS RED.
WARNING: EXPLOSION HAZARD
• neverusechemicals,gasoline,gas-
OLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR
FLAMMABLE LIQUIDS TO START OR “FRESH-
EN-UP” A FIRE IN THE STOVE.
• Keep all flammable liquiDs, espe-
CIALLY GASOLINE, OUT OF THE VICINITY
OF THE STOVE — WHETHER IN USE OR IN
STORAGE.
OPERATING SAFETY PRECAUTIONS
1. NEVER OVER FIRE THIS STOVE BY BUILD-
ING EXCESSIVELY HOT FIRES AS A HOUSE/
BUILDING FIRE MAY RESULT. YOU ARE OVER
FIRING THE STOVE IF STOVE OR STOVEPIPE
BEGINS TO GLOW OR TURN RED.
2. NEVER BUILD EXTREMELY LARGE FIRES
IN THIS TYPE OF STOVE AS DAMAGE TO THE
STOVE OR SMOKE LEAKAGE MAY RESULT.
3. STOVE IS HOTWHILE IN OPERATION. KEEP
CHILDREN, CLOTHING, AND FURNITURE AWAY
FROM HOT STOVE.CONTACT MAY CAUSE SKIN
BURNS. DO NOT TOUCH THE STOVE AFTER
FIRING UNTIL IT HAS COOLED.
4. PROVIDE AIR INTOTHE ROOM FOR PROP-
ER COMBUSTION.
5. INSPECT STOVEPIPE EVERY 60 DAYS.
REPLACE IMMEDIATELY IF STOVEPIPE IS
RUSTING OR LEAKING SMOKE INTO THE
ROOM.

Page 10 / BX42E VGZ-005 / 20100616
www.vogelzang.com
OPERATING INSTRUCTIONS continued …
2. When adding fuel be careful not to smother
the fire.
3. Close the feed door and secure tightly.
4. Adjust the damper and spin draft control.
5. Empty ashes regularly. Do not allow ashes
to pile up higher than the top of the hearth (see
Safety Instructions #13 page 2). If ashes build
up to the grate, burnout will occur.
6. Properly dispose of hot ashes (see Safety
Instructions, item #13 on page 2.)
7. Do not over fire the stove.
CAUTION: DO NOT OVER FIRE APPLIANCE.
TOO MUCH WOOD OR BURNING NON-REC-
OMMENDED MATERIALS SUCH AS TRASH OR
FLAMMABLE LIQUIDS MAY CAUSE OVER FIR-
ING. YOU ARE OVER FIRING IF THE CHIMNEY
CONNECTORS OR STOVE GLOWS RED. CLOSE
THE DOOR, SPIN DRAFT AND DAMPER IMME-
DIATELY TO REDUCE THE AIR SUPPLY TO THE
FIRE. THIS WILL SLOW DOWN THE FIRE.
MAINTENANCE & SERVICE HINTS
ASH DISPOSAL – Do not allow ashes to
accumulate higher than the optional grate or spin
damper. Dispose of properly. (See Safety Instruc-
tions #13, page 2.)
CHIMNEY DRAFT – Draft is a function of
the chimney, not the stove — do not expect the
stove to draw. Smoke spillage into the house or
excessive buildup of condensation or creosote in
the chimney are warnings that the chimney is NOT
functioning properly. Correct the problem before
using the stove. Following are some possible causes
for improper draft.
1. The connector stovepipe may be pushed
into the chimney too far, stopping the draft.
2. If the chimney temperature is too cool,
water will condense in the chimney and run back
into the stove. Creosote formation will be rapid
and may block the chimney. Operate the stove at a
fire level high enough to keep the chimney warm
to prevent condensation from forming.
3. If the fire burns well but sometimes creates
excess smoke or burns slowly, it may be caused by
the chimney top being lower than another part of
the house or a nearby tree. The wind blowing over
a house or tree, falls on top of the chimney like
water over a dam, beating down the smoke. The
top of the chimney should be at least three (3) feet
above the roof and be at least two (2) feet higher
than any point of the roof within ten (10) feet.
CREOSOTE – Formation and Removal.
Slow-burning wood produces tar and other organic
vapors which combine with expelled moisture to
form creosote. Creosote vapors condense in the
relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on
the flue lining. If ignited, this creosote creates an
extremely hot fire which may ignite surrounding
materials resulting in a building fire.
If creosote has accumulated, it should be
removed. Failure to remove creosote may result
in ignition and may cause a house/building fire.
Creosote may be removed using a chimney brush
or other commonly available materials from your
local hardware retailer.
continued on next page
CAUTION: SLOW BURNING FIRES AND
EXTENDED USE MAY CAUSE EXCES-
SIVE CREOSOTE BUILDUP. IGNITION OF
CREOSOTE BUILDUP OR OVER FIRING MAY
CAUSE A CHIMNEY FIRE. CHIMNEY FIRES
BURN EXTREMELY HOT AND MAY IGNITE
SURROUNDING MATERIALS. IN CASE OF A
CHIMNEY FIRE IMMEDIATELY LEAVE THE
BUILDING AND CALL THE FIRE DEPARTMENT
FROM A SAFE LOCATION.

VGZ-005 / 20100616 BX42E / Page 11
Vogelzang International Corp.
MAINTENANCE & SERVICE continued …
STOVE JOINTS – Required Tune-up.
This stove is manufactured with cast iron
components. IT DOES NOT HAVE WELDED
SEAMS. Periodic “tune up” may be required by
refilling and/or replacing the cement/joint mortar
along the seams where the cast iron components
meet.
CHIMNEY INSPECTIONS – The chimney
connector and chimney should be inspected at
the beginning of and at least twice a month dur-
ing the heating season to determine if a creosote
buildup has occurred.
Chimney fires burn very hot. If the chimney
connector should glow red, reduce the fire by
closing the damper and spin draft control and
immediately call the fire department.
CAUTION: A CHIMNEY FIRE MAY CAUSE
IGNITION OF WALL STUDS OR RAFTERS
WHICH WERE ASSUMED TO BE A SAFE
DI STAN CE FRO M TH E CH IM NE Y. I F A
CHIMNEY FIRE HAS OCCURRED, HAVE YOUR
CHIMNEY INSPECTED BY A QUALIFIED
EXPERT BEFORE USING AGAIN.
A fire in the stove may be smothered by
pouring a large quantity of coarse salt, baking soda,
or cool ashes on top of the fire.

Page 12 / BX42E VGZ-005 / 20100616
www.vogelzang.com
ORDERING PARTS - BX42E BOXWOOD STOVE
When ordering missing or replacement parts, always give the Model Number of the stove,
Part Number, and Part Description. Use the illustrations and part lists provided to identify parts.
Contact us at 616-396-1911 to order parts.
Part No. Description Qty.
1 Leg............................................................... 4
2 Bottom ......................................................... 1
3 Side ............................................................. 2
4 Back............................................................. 1
5 Front ............................................................ 1
6 Door............................................................. 1
7 Top............................................................... 1
8 Damper, Slide Draft .................................... 1
9 Lid................................................................ 2
10 Lid Support .................................................. 1
11 Hearth.......................................................... 1
12 Damper Collar Assembly............................. 1
13 Handle Assembly ........................................ 1
14 Lid Lifter (L-1) .............................................. 1
15 Hardware Pack ........................................... 1
16 S-Hook (used to hang lid lifter) .................... 1
17 Spin Draft .................................................... 1
18 Door Latch ................................................... 1
19 Gasket, Door (1/4” dia. fiberglass) ............... 1

VGZ-005 / 20100616 BX42E / Page 13
Vogelzang International Corp.

Page 14 / BX42E VGZ-005 / 20100616
www.vogelzang.com
This Vogelzang heating appliance is safe when installed properly and will provide you with years of
service. However, always exercise good judgement when you are using this stove. You are dealing with
FIRE! Fire is inherently dangerous and must be treated with respect. Stay warm and in good health!
Respectfully yours,
Proprietor
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
COMPANY TESTIMONY:
“FOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVER
BELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFE”
JOHN 3:16
MADE IN CHINA
SteveVogelzang
DO NOT USE THIS STOVE IN A
MOBILE HOME, MANUFACTURED HOME,
TRAILER OR TENT — NO EXCEPTIONS!