Vogelzang International Lit'l Sweetie BX22EL User manual

VGZ-003 / 2011613.0 BX22EL / Page 1
READ ALL INSTRUCTIONS CARE-
FULLY BEFORE STARTING THE
INSTALLATION OR OPERATING
THE STOVE. FAILURE TO FOLLOW
INSTRUCTIONS MAY RESULT IN
P R O PE R T Y DA M AG E , B O D I LY
INJURY, OR EVEN DEATH.
SAFETY INSTRUCTIONS
SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIRE MAY
RESULT. FORYOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT PERMITS,
RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA.
READ ALL INSTRUCTIONS CAREFULLY.
1. The installation of this stove must comply
with your local building code rulings. Please
observe the clearances to combustibles. Do
not place furniture or other objects within
the clearance area (see reference figures
1 & 2).
2. Do not install this stove in a mobile
home, manufactured home, trailer or tent
(NO EXCEPTIONS! per HUD Fede ral
Standard: 24 CFR Ch.XX).
3. Verify that the stove is properly installed before
firing the stove for the first time. After reading
these instructions, if you have any doubt about
your ability to complete your installation properly,
you must obtain the services of a professional
licensed installer familiar with all aspects of safe
and correct installation. DO NOT use
temporary or makeshift compromises
during installation.
4. If any parts are missing or defective, please
notify the dealer or manufacturer immediately.
DO NOT OPERATE A STOVE THAT IS MISSING
ANY PARTS!
5. Do not tamper with combustion air control beyond
normal adjustment capacities.
6. Always connect this stove to a chimney and vent to
the outside. Never vent to another room or inside
a building. DO NOT CONNECT THIS UNIT TO A
CHIMNEY FLUE SERVING ANOTHER APPLI-
ANCE.
7. DO NOT CONNECT a wood burning stove to an
aluminum Type B gas vent.This is not safe. Use ap-
proved masonry or a UL 103 HT Listed Residential
Type and Building Heating Appliance Chimney.Use
a 6”diameter chimney or larger, that is high enough to
give a good draft (See specifics in installation
instructions).
8. Be sure that your chimney is safely constructed
and in good repair. Have the chimney inspected
by the fire department or a qualified inspector.Your
insurance company should be able to recommend
a qualified inspector.
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
continued on next page
“Lit’l Sweetie” BOXWOOD STOVE
Model BX22EL Owners Manual
(save this manual for future reference)
DO NOT USE THIS STOVE IN A
MOBILE HOME, MANUFACTURED HOME,
TRAILER OR TENT – NO EXCEPTIONS!
This stove meets
U.S. Test Standard:
UL 1482-2006

Page 2 / BX22EL VGZ-003 / 20110613.0
away from a hot stove to avoid burns or clothing
ignition.
18. If small children will be in the same room as
the stove during operation, provide a stur-
dy barrier to keep them at a safe distance
from the stove. NE VER LEAVE S MAL L
CHILDREN UNSUPERVISED when they are in the
same room as the stove.
19. Keep stove area clear and free from all
combustible materials, gasoline, and other flam-
mable vapors and liquids.
20. While in operation, keep the feed door closed and
secured at all times except while tending the fire.
21. Do not over fire the stove. Over firing will occur if
the feed door is left open during operation. Such
actions can result in very dangerous operating
conditions.
22. All power cords and electrical appliances
and/or assemblies must be kept outside of the
clearance dimensions shown in this manual for
combustible materials.
23. DO NOT ELEVATE FIRE! Build fire directly on the
bottom of the firebox.This stove has not been tested
with the use of grates, andirons, or other means of
elevating the fire and they should not be used.
24. For further information on using your stove
safely, obtain a copy of the National Fire
Protection Association (NFPA) publication, “Using
Coal and Wood Stoves Safely” NFPA No. HS-10-
1978. The address of the NFPA is Batterymarch
Park, Quincy, MA 02269.
NOTE: A PROFESSIONAL, LICENSED HEAT-
ING AND COOLING CONTRACTOR SHOULD
BE CONSULTED IF YOU HAVE QUESTIONS
REGARDING THE INSTALLATION OF THIS
SOLID FUEL BURNING APPLIANCE.
9. Creosote or soot may build up in the chimney con-
nector and chimney and cause a house/building fire.
Inspect the chimney connector and chimney twice
monthly during the heating season and clean if
necessary (See Chimney Inspections, page 12).
10. In the event of a chimney fire, turn the air damper
to closed position, leave the building and CALL
THE FIRE DEPARTMENT IMMEDIATELY! Have
a clearly understood plan on how to handle a
chimney fire by contacting your local fire authority
for information on proper procedures in the event
of a chimney fire.
11. To prevent injury, do not allow anyone to use this
stove who is unfamiliar with the correct operation
of the stove.
12. D o n o t o p e rat e s t o ve w hil e u n d e r t h e
influence of drugs or alcohol.
13. To prevent bur ns, always wear protective
clothing, leather hearth gloves and eye
protection, while tending the fire.
14. Ashes should not be allowed to accumulate higher
than the slide damper. Dispose of ashes in a metal
container with a tight fitting lid.Other waste shall not
be placed in this container. Keep the closed con-
tainer on a noncombustible floor or on the ground,
well away from all combustible materials. Keep the
ashes in the closed container until all cinders have
thoroughly cooled.The ashes may be buried in the
ground or picked up by a refuse collector.
15. The special paints used on your stove may
give off some smoke and an odor while
they are curing during the first 12 to 15 fires. Addi-
tional smoke and odor may be emitted from the light
oils used in construction of the fire box.This should
disappear after a short period of time and not occur
again.Persons with lung conditions or owners of sus-
ceptible domestic pets (such as birds) should take
prudent precautions. Open windows and
doors as needed to clear smoke and/or odor.
Paint discoloration will occur if the stove is
over fired.
16. This stove has a pa inted su rface which
is durable but it will not stand rough handling
or abuse. When installing your stove, use care
in handling. Clean with soap and warm water
when stove is NOT hot. Do not use any acids
or scouring soap, as these solvents wear and dull
the finish.
17. While stove is in operation, all persons,
especially young children should be alerted to the
hazards from high surface temperatures. Keep
SAFETY INSTRUCTIONS continued…

VGZ-003 / 2011613.0 BX22EL / Page 3
ASSEMBLY INSTRUCTIONS
t o o l s r e q u i r e d
CAUTION: STOVE IS HEAVY. MAKE SUREYOU
HAVE ADEQUATE HELP AND USE PROPER
LIFTING TECHNIQUES WHENEVER MOVING
STOVE.
Refer to diagram and parts lists at back of this man-
ual.
1. Uncrate the stove and remove packing materials
and protective poly bag. (Save exterior cardboard
box for further assembly.)
2. Remove par ts from inside of stove. Par ts
include: one lid (L22-09), one damper collar (L22-
12), one feed door (L22-07), one lid lifter (L-1),
one slide damper (L22-06), seperable handle
(L22-17A), four legs (L22-01 & 01b), heat shield
(L22-14A), hardware pack (L22-HP), and S-Hook
(L22-00) from inside firebox.
m a t e r i a l s r e q u i r e d
(NOTE: The following items are NOT included with your stove)
the seperable
handle holder bracket
and this leg should be
used as one of the front legs. The long
mounting bolts (B) pass through the clearance
holes in the base of the stove, illustration C, through
the rear legs, the heat shield brackets and then are
secured with washers (E) and hex nuts (F).
6. The front legs attach in a similar method, illustration
D, with the bolts (B) passing through mounting holes
Screwdrivers
(blade and cross types)
5/16” Nut Driver or Ratchet
with 5/16” Socket (for 1/4”
Hex Nuts)
11mm Nut Driver or
Ratchet with 11mm Socket
(for Stove Bolts)
Safety Glasses
Pencil
6 foot Folding Rule or
Tape Measure
Tin Snips
Drill: Hand or Electric
1/8” dia. Drill Bit
(sheet metal screws)
Flooring Protection: 36” x 48”
as specified (see page 5)
Chimney Connection: 6”
dia. min. 24 MSG black or 26
MSG blue steel stove pipe or
elbow(s) required.
1/2” Sheet Metal Screws
Chimney: Existing 6” Lined Ma-
sonry Chimney or 6”Inside Dia.
listed Type HT chimney.
Furnace Cement (manufacturer
recommends Rutland Code 78
or equivalent)
continued on next page
NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance
of your wood stove and assumes no responsibility of any incidental or consequential damages.
3. Place flattened carton on floor and carefully turn
stove over onto carton.
4. Attach hearth to bottom of stove with two short
stove bolts (A), washers (E), and hex
nuts (F).
ill. A – Hardware Pack
ill. B – Hearth Assembly
in the hearth, through the leg, heat shield brackets
and are finally secured with washers (E) and hex
nuts (F).
7. Attach the handle holder bracket (L22-18) to the
front leg (L22-01b) with the mounting holes.
7. Carefully lift stove upright and place in desired loca-
tion (see following instructions for properly locating
stove).
8. Attach damper collar to rear top surface of stove,
illustration E, using short stove bolts (A) flat washers
(E) and hex nuts (F).
9. Place lid in position on top of stove.
ill. C –
Rear Leg & Heat
Shield Assembly
ill. D –
Front Leg &
Heat Shield
Assembly
5. The heat shield
(L22-14A), illus-
tration C, is held to
the stove with the
mounting bolts for
the legs. Note that
one of the legs has
mounting holes for

Page 4 / BX22EL VGZ-003 / 20110613.0
Proper clearances must be maintained for ad-
equate air circulation. Adequate ventilation must be
provided while operating this stove.
1. The stove must be placed on solid concrete, solid
masonry, or when installed on a combustible floor,
on a listed floor protector, such as Hy-C or Impe-
rial Model UL 3648BK, a 1/2” thick floor protector
with a R-factor of 0.84 or equivalent (see page
14 to calculate R-factors of alternative materials).
The base must extend at least 16” beyond the
front of the hearth, 8” to the sides of the stove,
and must extend under the stove pipe and 2˝
on either side if it is elbowed towards a wall (see
figure 1 and consult local building codes and fire
protection ordinances.)
CAUTION: (FIRE HAZARD) CARPETING AND
OTHER COMBUSTIBLE MATERIAL MUST NOT
COVER THE FLOOR PROTECTOR. THESE
MATERIALS MUST REMAIN OUTSIDE OF
COMBUSTIBLE CLEARANCES, SEE FIG. 1- 2.
2. The stove must have its own flue. DO NOT
CONNECT THIS UNIT TO A CHIMNEY FLUE
SERVING OTHER APPLIANCES.
3. After observing the clearances to combus-
tible materials (figure 1 & 2), locate your floor
protector accordingly (figure 1) and careful-
ly place the stove in your selected location.
Install connector pipe, elbows, and thimble as
required, utilizing either a recently cleaned and
inspected 6” masonry chimney or a 6” i.d. listed
chimney, maximum 64 square inches.
ASSEMBLY INSTRUCTIONS continued…
4. Use round, 6” dia., minimum 24 MSG (minimum
standard gauge) black or 26 MSG blue steel stove
pipe. DO NOT use galvanized stove pipe. Secure
pipe sections with three (3) sheet metal screws in
each stove pipe and/or elbow joint to firmly hold the
pipe sections together. DO NOT CONNECT THIS
STOVE TO ANY AIR DISTRIBUTION OR DUCT
SYSTEM.
5. R e c h e c k c l e a r a n c e s f r o m t h e s t o ve ,
connector stove pipe, and corner clearances
using the location drawings (figure 1 & 2) and
your local building codes or fire protection
ordinances.
NOTE: Drywall faced with brick or stone must be
considered a combustible surface.
6. DO NOT INSTALL THIS STOVE IN A MOBILE HOME,
MANUFACTURED HOME, TRAILER OR TENT – NO
EXCEPTIONS! (HUD Federal Standard: 24 CFR
Ch.XX)
7. The clearances provided are minimum
dimensions determined by NFPA. Installation of
this stove must comply with the latest edition of
NFPA 211 for reduced clearances and/or your lo-
cal building code rulings. Use whichever minimum
dimensions are LARGEST.
Failure to follow these minimum clear-
ance requirements may result in an unsafe
installation and could cause a fire.
10. Place the slide draft into position on the hearth,
illustration F. Hold in position with round head stove
bolt (C) and large flat washer (D).
11. Lower feed door into position while aligning hinge
pins.
12. Place S-Hook in hole at left front corner of hearth.
Note: S-Hook is used to hang lid lifter while not
in use.
LOCATING STOVE
ill. F – Slide Draft,
Door & S-Hook Location
(lid lifter storage)
ill. E – Damper Collar

VGZ-003 / 2011613.0 BX22EL / Page 5
Fig. 2 – Top View
Minimum Corner Clearances from
Combustible Surfaces
24.5"
24.5"
CORNER CLEARANCES
LOCATING STOVE continued…
COMBUSTIBLE
CONSTRUCTION IN
ACCORDANCE WITH
NFPA 211
FLOOR
PROTECTOR
DA SHED LINE SHOWS
HORIZONTAL CHIMNEY
CONNECTOR AND
ADDITIONAL FLOOR
PROTECTION REQUIRED
BACKWALL
27"
(TOP VIEW)
8"
8"
8"
26" 28"
26"
48"
16"
SIDEWALL
NON-COMBUSTIBLE
CONSTRUCTION IN
ACCORDANCE WITH
NFPA 211
Fig. 1 – Minimum Clearance Dimensions from Combustible Surfaces
CAUTION: KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS AWAY FROM THE
STOVE.
MINIMUM CLEARANCES
TO COMBUSTIBLE SURFACES
Unit to Sidewall........................ 26 inches
Unit to Backwall........................ 26 inches
Unit Corner to Wall ..................24.5 inches
Pipe Connector to Backwall .......... 28 inches
Pipe Connector to Ceiling ............ 18 inches

Page 6 / BX22EL VGZ-003 / 20110613.0
CONNECTOR PIPE INSTALLATION
NOTE: STOVE PIPE IS NOT INCLUDED.
TO PURCHASE, VISIT YOUR LOCAL HARD-
WARE, HOME OR BUILDING CENTER. USE
ROUND 6” DIA., MINIMUM 24 MSG (minimum
standard gauge) BLACK OR 26 MSG BLUE
STEEL STOVE PIPE. DO NOT USE GALVANIZED
STOVE PIPE. SEE “LOCATING STOVE” PAGES
4-5 FOR ADDITIONAL SPECIFICATIONS.
1. The crimped end of the stovepipe fits into the cast
iron damper collar. This first section must be single
walled to properly connect to the damper. Install
additional pipe and elbow(s) with the crimped end
towards the stove.This will allow any condensation
in the flue to run back into the firebox.
2. Horizontal pipe runs must slope upwards
towards the chimney at least 1/4” per foot of hori-
zontal run.
3. You must have at least 18 inches of clearance
between any horizontal piping and the ceiling.
4. The pipe cannot extend into the chimney flue (figure
3).
5. Secure pipe/elbow sections with three (3) sheet
metal screws at each joint to make the piping
rigid.
Fig. 3 – Stovepipe/Flue Connections
CORRECT WRONG WRONG
6. It is recommended that no more than two (2)
90° bends be used in the stovepipe installa-
tion. The use of more than two 90° bends may
decrease the amount of draw and possibly
cause smoke spillage. Where possible, use only
corrugated (nonadjustable) elbows. These
provide a better seal.
7. The connector pipe must not pass through an at-
tic or roof space, closet, or any concealed space,
or floor, ceiling, wall, or combustible construction.
(See Chimney Connector Systems & Clearances,
page 15). A UL 103 HT Listed chimney must be
used from the first penetration of ceiling or wall to
the chimney cap.
CAUTION: NEVER USE SINGLE WALL CON-
NECTOR PIPE AS A CHIMNEY - A HOUSE FIRE
COULD RESULT.

VGZ-003 / 2011613.0 BX22EL / Page 7
CHIMNEY CONNECTIONS
The stove must be connected to either a masonry
or manufactured metal chimney built and tested to the
specifications listed on the previous pages.
Chimneys perform two functions:
1). As a means of exhausting smoke and flue gases
which are the result of fuel combustion.
2). The chimney provides “draft” which allows oxy-
gen to be continuously introduced into the
appliance, so that proper combustion is possible.
This stove relies on natural draft to operate.
NOTICE: Always provide a source of fresh air
into the room where the stove is located. Failure
to do so may result in air starvation of other fuel
burning appliances and the possible development
of hazardous conditions, fire or death.
The stove DOES NOT create draft. Draft is created
by the chimney. To achieve proper draft your chimney
must meet the three minimum height requirements
detailed in figures 4–7. A minimum draft of 0.05 w.c.
(measured in water column) is required for proper
drafting to prevent back puffing, smoke spillage, and to
maximize performance. (Gauges to measure draft are
readily available at stove stores and are economical to
rent or purchase.)
Factors such as wind, barometric pressure, trees,
terrain and chimney temperature can have an adverse
effect on the draft. The manufacturer cannot be held
responsible for external factors leading to less than
optimal drafting.
Should you have a problem with inadequate draft,
you should contact a licensed heating and cooling con-
tractor for assistance in solving the problem.
IMPORTANT Installation Points
1. Size chimney flue to stove collar. This stove
requires a 6” diameter flue.
2. Never connect this unit to a chimney serving an-
other appliance.
3. The chimney must meet all minimum height require-
ments.
4. Never use a chimney to ventilate a cellar or base-
ment.
5. Contact your local building authority
for approved methods of installation and any
necessary permits and/or inspections.
MASONRY CHIMNEY
Before using an existing masonry chimney,
clean the chimney, inspect the flue liner and make
any repairs needed to be sure it is safe to use.
Make repairs before attaching the stove. The con-
nector stove pipe and fittings you will need to con-
nect directly to a masonry chimney are shown in
figure 4.
Fig. 5 - Chimney Construction Through Attic Space
If the connector stove pipe must go through a
combustible wall before entering the masonry chimney,
consult a qualified mason or chimney dealer.The instal-
lation must conform to local building and fire codes and
latest edition of NFPA 211.
If there is a cleanout opening in the base of the
chimney, close it tightly.
CHIMNEY
FLUE
5/8" TILE
CHIMNEY
LINER
MASONRY
CHIMNEY
THIMBLE
COLLAR
6˝ ROUND
24 ga. BLACK
STOVEPIPE
8˝ MIN.
LINER
BELOW
ENTRY
HOLE
Fig. 4 - Masonry Chimney Connection

Page 8 / BX22EL VGZ-003 / 20110613.0
Fig. 6 - Chimney Construction Through Roof
Fig. 7 - Chimney Connection to Firebox
Through Masonry Wall
CHIMNEY CONNECTIONS continued …
MANUFACTURED CHIMNEY
REFER TO CHIMNEY AND CHIMNEY CONNEC-
TOR MAKER’S INSTRUCTIONS FOR INSTALLATION
AND USE.
continued on next page
Use only 6” diameter listed chimney UL 103 HT.
Chimney made to this listing is High Temperature rated
to 2100 degrees Fahrenheit.Use chimney from only one
manufacturer. Never mix brands. Carefully follow the
chimney manufacturer’s stated requirements and clear-
ances. Use the chimney manufacturer’s attic guards,
roof supports, flashing, and fire stops when passing
through a ceiling. Use a listed thimble when passing
through a combustible wall. Do not use makeshift com-
promises during installation. Never use a single-wall
connection pipe as a chimney!
When using a pre-existing chimney, have it’s condi-
tion and installation inspected before using. Make sure
that the chimney meets all of the UL rating requirements
listed above. Be aware that not all manufactured chim-
ney is of the UL 103 HT type.
NOTE: It is recommended that you contact a li-
censed heating and cooling contractor (consult your
local yellow pages) for chimney installation.
Manufactured chimney with the proper required UL
listing is available from most home centers, hardware
stores, and HVAC supply stores.
If you have access to the internet, you may wish
to view chimney manufacturers’ information on-line.
See, www.duravent.com, www.selkirkinc.com, or
www.mtlfab.com.
VENTING TO EXISTING FIREPLACE
In some instances, people desire to convert an
existing fireplace for stove use. Usually, safe connec-
tion to an existing masonry chimney requires more
work than using a prefabricated chimney. The existing
fireplace must be closed and sealed at the damper with
high-temperature caulk, ceramic wool, or furnace ce-
ment.Prior to installation, clean and inspect the existing
flue and smoke shelf. Installation should be designed
so the system can be dismantled for periodic cleaning
and inspection. Before conversion, make sure the
existing chimney is structurally sound, the chim-
ney incorporates a flue liner and make sure it is in
good condition. (A flue liner consists of clay tile that
protects the brickwork of a chimney. If a chimney does
not have a liner, or it is damaged, have it relined by a
professional. DO NOT USE a chimney that is unlined
or damaged!) If you have any question regarding the
condition of the chimney, consult a qualified licensed
contractor, qualified engineer, competent mason, cer-
tified Chimney Sweep, or a knowledgable inspector.
Consult your insurance company if you cannot find a
qualified expert.
CAUTION: NOT ALL FIREPLACE CHIMNEYS
ARE SUITABLE FOR USEWITH A WOOD STOVE.
CHECK WITH A QUALIFIED EXPERT.
Many prefabricated fireplaces are of the “zero-clear-
ance fireplace” category. These consist of multilayered
metal construction. They are designed with enough
insulation and/or air cooling on the base, back and sides
so they can be safely installed in direct contact with
combustible floors and walls. Although many prefab-
ricated fireplaces carry endorsements from nationally
recognized organizations for use as fireplaces, they
have not been tested for connection to wood stove
heaters. Connecting a stove to such a device will void
the manufacturer’s warranty.

VGZ-003 / 2011613.0 BX22EL / Page 9
CHIMNEY CONNECTIONS continued …
Steel-lined fireplaces are constructed with
1/4” firebox liner, an air chamber in connection with 8”
of masonry. These can be safely used with wood burn-
ing stoves. They contain all the essential components
of a fireplace, firebox, damper, throat, smoke shelf,
and smoke chamber. Many look identical to masonry
fireplaces and should be checked carefully before con-
necting a stove to them.
Venting a stove directly into a fireplace does not
meet code and should not be attempted. (This consti-
tutes connection to another appliance - the fireplace.)
Combustion products will be deposited and build up in
the firebox or fireplace. The stove warranty will be void
with such an installation. Do not create a hazard in your
home by connecting in this manner.
FIREPLACE INSTALLATION
Directly connecting the stovepipe into the existing
masonry chimney (figure 8 “Type A” Fireplace Conver-
sion) of the fireplace is the only approved method of
installation.This is a complicated and involved process
and to ensure safety should only by done by a qualified
installer.
Fig. 8 - Fireplace Conversion
3. Secure the thimble with refractory mortar. The
thimble should be surrounded by 8” of solid unit
masonry brickwork or 24” of stone.
4. Install the stovepipe into the thimble as far as pos-
sible without extending past the flue lining (see
figures 3 on page 6).
5. A small airspace (about 1/2”) should remain
between the stovepipe and thimble to allow for
expansion of the pipe. Seal this airspace with high-
temperature caulking or ceramic wool.
6. Secure and seal the damper in the closed posi-
tion using high-temp caulking, ceramic wool, or
furnace cement. Also check to see if the chimney
has a cleanout. If it does, make sure it is closed and
sealed as well. A leaky cleanout will greatly reduce
draft efficiency.
If you have any questions regarding venting your
stove, contact the manufacturer or contact the Na-
tional Fire Protection Association (NFPA) and request
a copy of the latest editions of NFPA Standard 211
and NFPA Standard 908. Their address is:
Battery March Park, Quincy, MA 02269.
1. An entry hole must be cut through the masonry and
tile liner with minimal damage to the liner. At least 8”
of liner must remain below the entry position.When
locating the stove and stovepipe, all minimum clear-
ances must be observed from combustible surfaces
including mantels, combustible trimwork, ceilings,
and walls. Positioning the center of the stove pipe
entry into the chimney 24” below the ceiling should
insure proper clearance for a 6” stovepipe.
2. Install a metal or fire clay (5/8” minimum thickness)
thimble.Make sure the thimble is flush with the inner
surface of the chimney liner and does not protrude
into the flue (see figure 3 on page 6).

Page 10 / BX22EL VGZ-003 / 20110613.0
OPERATING INSTRUCTIONS
CAUTION: HOUSE FIRE HAZARDS
• DonotstorewooDonfloorprotec-
TOR, UNDERNEATH STOVEPIPE, OR ANY-
WHEREWITHIN MINIMUM CLEARANCES FROM
COMBUSTIBLE SURFACES SPECIFIED FOR
THIS STOVE.
• overfiring may cause a house fire.
YOU ARE OVERFIRING IF THE STOVE OR
CHIMNEY CONNECTOR GLOWS RED.
WARNING: EXPLOSION HAZARD
• neverusechemicals,gasoline,gas-
OLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR
FLAMMABLE LIQUIDS TO START OR “FRESH-
EN-UP” A FIRE IN THE STOVE.
• Keep all flammable liquiDs, espe-
CIALLY GASOLINE, OUT OF THE VICINITY
OF THE STOVE — WHETHER IN USE OR IN
STORAGE.
OPERATING SAFETY PRECAUTIONS
1. NEVER OVERFIRE THIS STOVE BY BUILD-
ING EXCESSIVELY HOT FIRES AS A HOUSE/
BUILDING FIRE MAY RESULT.YOU ARE OVER-
FIRING THE STOVE IF STOVE OR STOVEPIPE
BEGINS TO GLOW OR TURN RED.
2. NEVER BUILD EXTREMELY LARGE FIRES
IN THIS TYPE OF STOVE AS DAMAGE TO THE
STOVE OR SMOKE LEAKAGE MAY RESULT.
3. STOVE IS HOT WHILE IN OPERATION. KEEP
CHILDREN, CLOTHING, AND FURNITURE AWAY
FROM HOT STOVE. CONTACT MAY CAUSE
SKIN BURNS. DO NOT TOUCH THE STOVE
AFTER FIRING UNTIL IT HAS COOLED.
4. PROVIDE AIR INTO THE ROOM FOR PROP-
ER COMBUSTION.
5. INSPECT STOVEPIPE EVERY 60 DAYS.
REPLACE IMMEDIATELY IF STOVEPIPE IS
RUSTING OR LEAKING SMOKE INTO THE
ROOM.
This stove is designed to burn
WOOD FUEL ONLY.
Hardwood, 18” to 20” should be split and air dried
(seasoned), for 6 months to obtain maximum burning
efficiency. Wood should be stored in a dry, well venti-
lated area.
NOTICE: USE SOLID WOOD MATERIALS ONLY.
DO NOT BURN PELLETS, PRESSED LOGS,
GARBAGE OR FLAMMABLE FLUIDS. DO NOT
USE COAL OR CHARCOAL AS THEY WILL
DESTROY THE FIREBOX.
NOTE: A 2” layer of sand or a layer
of firebrick should be used as bottom
insulation in the Boxwood stove.
LIGHTING
1. Open draft damper fully to provide maximum
draft.
2. Open the feed door and place several wads of
crushed paper in the firebox.
3. Lay small stacks of kindling on the paper to start
the fire.
4. Light the paper and kindling, close the door and
secure tightly.
5. Add fuel after fire is burning briskly. Use care not to
smother the kindling fire when adding wood. Close
the door and secure tightly.
6. Adjust the draft damper and slide draft
control. The more closed the slide draft is set, the
lower and slower the fire will burn. The more open,
the faster and hotter the fire will burn. Do not over-
fire the stove.
ADDING FUEL
Add small amounts of fuel each hour or so
instead of piling large quantities of fuel at one
time. This will ensure a more complete combustion
process and less buildup of tars, soot, or creosote will
occur in the chimney.
1. Always open draft damper before opening the feed
door.
2. When adding fuel be careful not to smother the
fire.
3. Close the feed door and secure tightly.
4. Adjust the damper and slide draft control.
5. Empty ashes regularly. Do not allow ashes to pile
up higher than the top lip of the slide draft.
continued on next page

VGZ-003 / 2011613.0 BX22EL / Page 11
OPERATING INSTRUCTIONS continued …
6. Properly dispose of hot ashes (see Safety
Instructions, item #13 on page 2.)
7. Do not overfire the stove.
CAUTION: DO NOT OVERFIRE APPLIANCE.
TOO MUCH WOOD OR BURNING NON-
RECOMMENDED MATERIALS SUCH AS
TRASH OR FLAMMABLE LIQUIDS MAY CAUSE
OVERFIRING. YOU ARE OVERFIRING IF THE
CHIMNEY CONNECTORS OR STOVE GLOWS
RED. CLOSE THE DOOR, SLIDE DRAFT, AND
DAMPER IMMEDIATELY TO REDUCE THE AIR
SUPPLY TO THE FIRE.THIS WILL SLOW DOWN
THE FIRE.
CAUTION: SLOW BURNING FIRES AND EX-
TENDED USE MAY CAUSE EXCESSIVE CREO-
SOTE BUILDUP. IGNITION OF CREOSOTE
BUILDUP OR OVERFIRING MAY CAUSE A
CHIMNEY FIRE. CHIMNEY FIRES BURN EX-
TREMELY HOT AND MAY IGNITE SURROUND-
ING MATERIALS. IN CASE OF A CHIMNEY FIRE
IMMEDIATELY LEAVE THE BUILDING AND
CALL THE FIRE DEPARTMENT FROM A SAFE
LOCATION.

Page 12 / BX22EL VGZ-003 / 20110613.0
MAINTENANCE & SERVICE HINTS
ASH DISPOSAL – Do not allow ashes to
accumulate higher than the slide draft. Dispose of
properly. (See Safety Instructions #14, page 2.)
CHIMNEY DRAFT – Draft is a function of the chim-
ney, not the stove — do not expect the stove to draw.
Smoke spillage into the house or excessive buildup of
condensation or creosote in the chimney are warnings
that the chimney is NOT functioning properly. Correct
the problem before using the stove. Following are some
possible causes for improper draft.
1. The connector stovepipe may be pushed into
the chimney too far, stopping the draft.
2. If the chimney temperature is too cool,
water will condense in the chimney and run back into
the stove. Creosote formation will be rapid and may
block the chimney. Operate the stove at a fire level high
enough to keep the chimney warm to prevent conden-
sation from forming.
3. If the fire burns well but sometimes creates
excess smoke or burns slowly, it may be caused by the
chimney top being lower than another part of the house
or a nearby tree.The wind blowing over a house or tree,
falls on top of the chimney like water over a dam, beating
down the smoke. The top of the chimney should be at
least three (3) feet above the roof and be at least two
(2) feet higher than any point of the roof within ten (10)
feet.
CREOSOTE – Formation and Removal. Slow-
burning wood produces tar and other organic va-
pors which combine with expelled moisture to
form creosote. Creosote vapors condense in the
relatively cool chimney flue of a slow-burning fire.
As a result, creosote residue accumulates on
the flue lining. If ignited, this creosote creates an
extremely hot fire which may ignite surrounding materi-
als resulting in a building fire.
If creosote has accumulated, it should be
removed. Failure to remove creosote may result in igni-
tion and may cause a house/building fire. Creosote may
be removed using a chimney brush or other commonly
available materials from your local hardware retailer.
CHIMNEY INSPECTIONS – The chimney connec-
tor and chimney should be inspected at the beginning
of and at least twice a month during the heating sea-
son to determine if a creosote buildup has occurred.
Chimney fires burn very hot. If the chimney
connector should glow red, reduce the fire by
closing the damper and spin draft control and
immediately call the fire department.
CAUTION: A CHIMNEY FIRE MAY CAUSE IGNI-
TION OF WALL STUDS OR RAFTERS WHICH
WERE ASSUMED TO BE A SAFE DISTANCE
FROM THE CHIMNEY. IF A CHIMNEY FIRE
HAS OCCURRED, HAVE YOUR CHIMNEY IN-
SPECTED BY A QUALIFIED EXPERT BEFORE
USING AGAIN.
A fire in the stove may be smothered by
pouring a large quantity of coarse salt, baking soda, or
cool ashes on top of the fire.
STOVE JOINTS – Required Tune-up.
This stove is manufactured with cast iron
components. IT DOES NOT HAVE WELDED SEAMS.
Periodic “tune up” may be required by refilling and/or
replacing the cement/joint mortar along the seams
where the cast iron components meet.

VGZ-003 / 2011613.0 BX22EL / Page 13
ORDERING PARTS - BX22EL BOXWOOD STOVE
When ordering missing or replacement parts, always give the Model Number of the stove,
Part Number, and Part Description. Use the illustration and parts list provided to identify parts.
01 L22-01 Leg................................................. 3
01b L22-01b Leg (with mounting holes) ............. 1
02 L22-02 Bottom ........................................... 1
03 L22-03 Side ............................................... 2
04 L22-04 Back............................................... 1
05 L22-05 Slide Draft Damper ........................ 1
06 L22-06 Front .............................................. 1
07 L22-07 Feed Door...................................... 1
08 L22-08 Top................................................. 1
09 L22-09 Lid.................................................. 1
10 L22-10 Hearth.......................................... 11
11 L22-11 Door Pin......................................... 2
12 L22-12A Damper Collar Assembly............... 1
13 L-1 Lid Lifter ........................................ 1
14 L22 14A Heat Shield Assembly ................... 1
15 L22-15 Heat Shield Hanger ....................... 4
16 L22-16 Heat Shield Separator ................... 4
17 L22-17A Separable Handle Assembly ......... 1
18 L22-18 Handle Holder................................ 1
19 L22-HP Hardware Pack, Complete ............ 1
29 M6x1 Hex Nut..................................... 4
31 M6x1 x 8 Pan Hd. Mach. Srew ................. 2
32 M6 Lock Washer............................. 4
35 M6x1 x 45 Leg Bolt .................................... 4
36 L22-S S-hook ...................................... 1
Ref. Part
No. No. Description Qty.
Ref. Part
No. No. Description Qty.

Page 14 / BX22EL VGZ-003 / 20110613.0
FLOOR PROTECTOR MATERIAL CALCULATIONS
This stove has been tested for and must be installed on a floor protector with the proper Thermal Resistance or R-value
as stated in the installation instructions on page 3, “Locating Stove” step 1, of this manual. If the floor protector materials
listed in the instructions are not available, materials with an equivalent R-value may be substituted.
Alternate materials may be rated with C-factor (Thermal Conductance) or k-factor (Thermal Conductivity) ratings
which must be converted to R-value to determine if the alternate material meets the tested requirements. The following
instructions provide the proper information and formulas for conversion to R-value.
To determine if alternate materials are acceptable follow this sequence.
1. Convert material specifications to R-value:
a. R-value given — no conversion necessary
b. k-factor is given with a required thickness (T) in inches:
R = 1/k x T
c. C-factor is given: R = 1/C
2. Determine the R-value of proposed alternate floor protector:
a. Use formulas in step 1 above to calculate R-value of proposed material(s).
b. For multiple layers, add R-values of each layer to determine overall R-value.
3. If the overall R-value of the floor protector system is equal to or greater than the floor protector specifications given,
the alternate is acceptable.
Definitions:
Thermal conductance (C) = BTU =W
(hr)(ft2)(°F) (m2)(°K)
Thermal conductivity (k) = (Btu)(inch) =W =Btu
(hr)(ft2)(°F) (m)(°K) (hr)(ft)(°F)
Thermal resistance (R) = (ft2)(hr)(°F) =(m2)(°K)
Btu W
Example:
The specs of floor protector material should be 3/4-inch thick material with a k-factor of 0.84.
The proposed alternative material is 4” brick with a C-factor of 1.25 over 1/8-inch mineral board
with a k-factor of 0.29.
Step 1: Convert specs to R-value.
R = 1/k x T = 1/0.84 x 0.75 = 0.893 System must have a R-value of 0.893 = Rspecs
Step 2: Calculate R-value of individual components
4” Brick with C-factor = 1.25. R = 1/C = 1/1.25 = 0.80 = Rbrick
1/8-inch (0.125”) mineral board with k-factor = 0.29. R = 1/0.29 x 0.125 = 0.431 = Rmin.brd.
Step 3: Add R-values of components to get total R-value of system
Rbrick + Rmin.brd = 0.80 + 0.431 = 1.231 = Rsystem
Step 4: Compare Rsystem to Rspecs
Rsystem = 1.231 is larger than Rspecs of 0.893. System R-value exceeds the required
specifications and therefore is an acceptable alternative.

VGZ-003 / 2011613.0 BX22EL / Page 15
A. Brick Masonry
Minimum 3.5˝/ 89mm thick brick masonry all framed
into combustible wall with a minimum of 12˝/305mm
brick separation from clay liner to combustibles. The
fireclay liner shall run from outer surface of brick wall
to, but not beyond, the inner surface of chimney flue
liner and shall be firmly cemented in place.
B. Insulated Sleeve
Solid-insulated, listed factory-built chimney length of
the same inside diameter as the chimney connector and
having 1˝/25.4mm or more of insulation with a mini-
mum 9˝/229mm air space between the outer wall of the
chimney length and combustibles.
C. Ventilated Thimble
Sheet steel chimney connector, minimum 24 gauge in
thickness, with a ventilated thimble, minimum 24 gauge
in thickness, having two 1˝/25.4mm air channels, sepa-
rated from combustibles by a minimum of 6˝/152mm
of glass fiber insulation. Opening shall be covered, and
thimble supported with a sheet steel support, minimum
24 gauge in thickness.
D. Chimney Section Pass-through
Solid insulated, listed factory-built chimney length with
an inside diameter 2˝/51mm larger than the chimney
connector and having 1˝/25.4mm or more of insulation,
serving as a pass-through for a single wall sheet steel
chimney connector of minimum 24 gauge thickness, with
a minimum 2˝/51mm air space between the outer wall of
chimney section and combustibles. Minimum length of
chimney section shall be 12˝/305mm chimney section
spaced 1˝/25.4mm away from connector using sheet steel
support plates on both ends of chimney section. Open-
ing shall be covered, and chimney section supported on
both sides with sheet steel support securely fastened to
wall surfaces of minimum 24 gauge thickness. Fasten-
ers used to secure chimney section shall not penetrate
chimney flue liner.
CHIMNEY CONNECTOR SYSTEMS & CLEARANCES

Page 16 / BX22EL VGZ-003 / 20110613.0
This Vogelzang heating appliance is safe when installed properly and will provide you with years of service.
However, always exercise good judgement when you are using this stove. You are dealing with FIRE! Fire is
inherently dangerous and must be treated with respect. Stay warm and in good health!
Respectfully yours,
Proprietor
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
COMPANY TESTIMONY:
“FOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVER
BELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFE”
JOHN 3:16
DO NOT USE THIS STOVE IN A
MOBILE HOME, MANUFACTURED HOME,
TRAILER OR TENT — NO EXCEPTIONS!
MADE IN CHINA