Vogelzang International PB65XL User manual

VGZ-003 / 20110524.0 PB65XL / Page 1
READ ALL INSTRUCTIONS CARE-
FULLY BEFORE STARTING THE
INSTALLATION OR OPERATING
THE STOVE. FAILURE TO FOLLOW
INSTRUCTIONS MAY RESULT IN
P R O PE R T Y DA M AG E , B O D I LY
INJURY, OR EVEN DEATH.
SAFETY INSTRUCTIONS
SAFETY NOTICE: IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE/BUILDING FIRE MAY
RESULT. FORYOUR SAFETY, CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT PERMITS,
RESTRICTIONS, AND INSTALLATION REQUIREMENTS FOR YOUR AREA.
READ ALL INSTRUCTIONS CAREFULLY.
1. The installation of this stove must comply
with your local building code rulings. Please
observe the clearances to combustibles (see
reference figures 2 – 4).
2. Do not install this stove in a mobile home,
manufactured home, trailer or tent
(NO EXCEPTIONS! per HUD Federal
Standard: 24 CFR Ch.XX).
3. Verify that the stove is properly installed
before firing the stove for the first time.
After reading these instructions, if you have
any doubt about your ability to complete
your installation properly, you must ob-
tain the services of a professional licensed
installer familiar with all aspects of safe
and correct installation. DO NOT use
temporary or makeshift compromises
during installation.
4. If any parts are missing or defective, please
notify the dealer or manufacturer immedi-
ately. DO NOT OPERATEA STOVE THAT
IS MISSING ANY PARTS!.
5. Do not tamper with combustion air control
beyond normal adjustment capacities.
6. Always connect this stove to a chimney and
vent to the outside. Never vent to another room
or inside a building. DO NOT CONNECT
THIS UNIT TO A CHIMNEY FLUE SERV-
ING ANOTHER APPLIANCE.
7. DO NOT CONNECT a wood burning stove
to an aluminum Type B gas vent. This is not
safe. Use approved masonry or a UL 103 HT
Listed Residential Type and Building Heat-
ing Appliance Chimney. Use a 6” diameter
chimney or larger, that is high enough to give
a good draft. (See specifics in installation
instructions).
8. Be sure that your chimney is safely con-
structed and in good repair. Have the chimney
inspected by the fire department or a qualified
inspector. Your insurance company should be
able to recommend a qualified inspector.
9. Creosote or soot may build up in the chimney
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
continued on next page
RailRoad Potbelly stove
Model PB65XL Owners Manual
(save this manual for future reference)
DO Not USE THIS STOVE IN A
MOBILE HOME, MANUFACTURED HOME,
TRAILER OR TENT — NO EXCEPTIONS!
NOTE: THIS STOVE IS
Not A UL LISTED STOVE.

Page 2 / PB65XL VGZ-003 / 20110524.0
Keep away from a hot stove to avoid burns or
clothing ignition.
17. If small children will be in the same room
as the stove during operation, provide a
sturdy barrier to keep them at a save distance
from the stove. NEVER LEAVE SMALL
CHILDREN UNSUPERVISED when they
are in the same room as the stove.
18. Keep stove area clear and free from all
combustible materials, gasoline, and other
flammable vapors and liquids.
19. To prevent burns, always wear protective
clothing, leather hearth gloves and eye
protection, while tending the fire.
20. While in operation, keep the feed and ash doors
closed and secured at all times except while
tending the fire.
21. Do not overfire the stove. Overfiring will
occur if the feed or ash doors are left open dur-
ing operation. Such actions can result in very
dangerous operating conditions.
22. All power cords and electrical appliances
must be kept outside of the clearance dimen-
sions shown in this manual for combustible
materials.
23. For further information on using your stove
safely, obtain a copy of the National Fire
Protection Association (NFPA) publication,
“Using Coal and Wood Stoves Safely” NFPA
No. HS-10-1978. The address of the NFPA is
Batterymarch Park, Quincy, MA 02269.
SAFETY INSTRUCTIONS continued…
NOTE: A PROFESSIONAL, LICENSED
HEATING AND COOLING CONTRAC-
TOR MUST BE CONSULTED IF YOU
HAVE QUESTIONS REGARDING THE
INSTALLATION OF THIS SOLID FUEL
BURNING APPLIANCE.
connector and chimney and cause a house/
building fire. Inspect the chimney connector
and chimney twice monthly during the heating
season and clean if necessary. (See Mainte-
nance, page 10).
10. In the event of a chimney fire, turn the air
controls and flue damper to closed position,
leave the building and CALL THE FIRE DE-
PARTMENT IMMEDIATELY! Have a clearly
understood plan on how to handle a chimney
fire by contacting your local fire authority for
information on proper procedures in the event
of a chimney fire.
11. To prevent injury, do not allow anyone to use
this stove who is unfamiliar with the correct
operation of the stove.
12. Do not operate stove while under the
influence of drugs or alcohol.
13. The special paints used on your stove may
give off some smoke and an odor while
they are curing during the first 12 to 15 fires.
Additional smoke and odor may be emitted
from the light oils used in construction of the
fire box. This should disappear after a short
period of time and not occur again. Persons
with lung conditions or owners of susceptible
domestic pets (such as birds) should take
prudent precautions. Open windows and
doors as needed to clear smoke and/or odor.
Paint discoloration will occur if the stove is
over fired.
14. Ashes should not be allowed to accumulate
higher than the ash pan. Dispose of ashes in a
metal container with a tight fitting lid. Other
waste shall not be place in this container. Keep
the closed container on a noncombustible floor
or on the ground, well away from all combus-
tible materials. Keep the ashes in the closed
container until all cinders have thoroughly
cooled. The ashes may be buried in the ground
or picked up by a refuse collector.
15. This stove has a painted surface which
is durable but it will not stand rough handling
or abuse. When installing your stove, use care
in handling. Clean with soap and warm water
when stove is NOT hot. Do not use any acids
or scouring soap, as these solvents wear and
dull the finish.
16. While stove is in operation, all persons,
especially young children should be alerted to
the hazards from high surface temperatures.

VGZ-003 / 20110524.0 PB65XL / Page 3
t o o l s r e q u i r e d
CAUTION: STOVE IS HEAVY. MAKE SURE YOU
HAVE ADEQUATE HELP AND USE PROPER
LIFTING TECHNIQUES WHENEVER MOVING
STOVE.
Refer to diagram and parts lists at back of this
manual.
1. Uncrate the stove and remove all protective
packing materials and protective poly bag.
(Save cardboard carton for further assembly.)
2. Remove parts from inside of stove. Parts
include: one lid (#1), one lid lifter (#2), one
ash door (#16) with one slide draft (#17), one
ash drawer (#19), four legs (#15), hardware
pack (#21), draft damper (#20), and one Spring
Handle (#9) from inside the firebox.
3. Place flattened carton on floor and carefully
turn stove over onto carton.
4. Securely attach all four legs to base of stove
with stove bolts.
5. Carefully lift stove upright and place in
desired location (see following instructions
for properly locating stove from
combustible materials).
6. Place lid (#1) in position on top plate.
7. Place ash drawer (#19) into lower chamber
(#13). Position ash door (#16) with slide draft
(#17) on front of lower chamber (#13).
ASSEMBLY INSTRUCTIONS
m a t e r i a l s r e q u i r e d
(NOTE: The following items are NOT included with your stove)
8. Place shaker grate (#12) in lower chamber.
9. Install flue pipe draft damper (#20) into the
top end of the first straight section of stove
pipe (fig.1) exiting the stove before the stove
is used.
a. Drill two 1/4” holes centered on either side of
the pipe section 6” from the top end of the pipe
(figure 1).
b. Remove the handle from the damper then slide
the damper into the pipe.
c. Align the damper with the holes drilled in step
9a and insert the handle through the holes and
the damper.
NOTE:THIS DAMPER IS NECESSARY FOR THE
PROPER OPERATION OF THE STOVE AND
TO MEET EPA EMISSIONS REQUIREMENTS
FOR HEATING APPLIANCES. IT MUST BE IN-
STALLED BEFORE USE. (NO EXCEPTIONS)
10. Attach stove piping — see instructions on
page 5.
1/8” dia. Drill Bit
(sheet metal screws)
Phillips Style Screwdriver
14mm Nut Driver or Ratchet
with 14mm Socket (for 14mm
Hex Nuts & Stove Bolts)
Safety Glasses
Hearth Gloves
Pencil
6 foot Folding Rule or
Tape Measure
Tin Snips
Drill: Hand or Electric
Flooring Protection: 54” x 63”
min. as specified (see page 4)
Chimney Connection: 6” black
steel (24 ga. min.) straight or
elbow (as required)
1/2” Sheet Metal Screws
Chimney: Existing 6” Lined Ma-
sonry Chimney or 6”Inside Dia.
listed Type HT chimney.
Furnace Cement (manufacturer
recommends Rutland Code 78
or equivalent)
6"/15.25 cm
Draft Damper
(must be installed
before use — NO
EXCEPTIONS!)
NOTICE: Vogelzang International Corp. grants no warranty, stated or implied, for the installation or maintenance of
your wood stove and assumes no responsibility of any incidental or consequential damages.
Fig. 1 – Draft
Damper Installation

Page 4 / PB65XL VGZ-003 / 20110524.0
36"
CORNER CLEARANCES
36"
LOCATING STOVE
Proper clearances must be maintained for adequate
air circulation. Adequate ventilation must be
provided while operating this stove.
1. The stove must be placed on solid con-
crete, solid masonry, or on an listed
floor protector, such as Hy-C or Impe-
rial Model UL 5463BK when installed on a
combustible floor. The base must extend at
least 18” beyond the front, rear and sides of the
stove, and must extend under the stove pipe if
it is elbowed towards a wall (see figure 5 and
consult local building codes and fire protection
ordinances.)
2. The stove must have its own flue. DO NOT
CONNECT THIS UNIT TO A CHIMNEY
FLUE SERVING OTHER APPLIANCES.
3. After observing the clearances to combustible
materials (figure 2 – 4), locate your floor
protector accordingly (figure 2) and care-
fully place the stove in your selected location.
Install stove pipe, stove pipe damper, elbows,
and thimble as required, utilizing either a
recently cleaned and inspected 6” masonry
chimney or a 6” i.d. listed chimney. Maximum
64 square inches.
FLOOR
PROTECTOR
DASHED LINE SHOWS
HORIZONTAL CHIMNEY
CONNECTOR AND
ADDITIONAL FLOOR
PROTECTION REQUIRED
BACKWA LL
54" (TOP VIEW)
36"
18"
18" 18"
36"
63"
18"
SIDEWALL
COMBUSTIBLE
CONSTRUCTION
ACCORDING TO
NFPA 211
COMBUSTIBLE
CONSTRUCTION
ACCORDING TO
NFPA 211
4. Use 6” round black stove pipe. DO NOT use
galvanized duct pipe. Secure pipe sections with
three (3) sheet metal screws in each stove pipe
and/or elbow joint to firmly hold the pipe sec-
tions together. DO NOT CONNECT THIS
STOVE TO ANY AIR DISTRIBUTION OR
DUCT SYSTEM.
5. Recheck clearances from the stove,
connector stove pipe, and corner clearances
using the illustrations (figure 2, 3 & 4) and
your local building codes or fire protection
ordinances.
NOTE: Drywall faced with brick or stone must
be considered a combustible surface.
6. DO NOT INSTALL THIS STOVE
IN A MOBILE HOME,TENT ORTRAILER.
(NO EXCEPTIONS)
7. The clearances provided are minimum
dimensions. Installation of this stove must
comply with your local building code rul-
ings.
8. This stove is NOT a UL listed stove.
Continued on next page
Fig. 2 Minimum Clearance Dimensions from Combustible Surfaces Fig. 3
MINIMUM CLEARANCES
TO COMBUSTIBLE SURFACES
Unit to Sidewall....................................36 inches
Unit to Backwall ...................................36 inches
Unit Corner to Wall................................36 inches
Pipe Connector to Backwall......................38 inches
Pipe Connector to Ceiling ........................18 inches
Fig. 4 – Top View
Minimum Corner Clearances from
Combustible Surfaces

VGZ-003 / 20110524.0 PB65XL / Page 5
CONNECTOR PIPE INSTALLATION
LOCATING STOVE continued…
1. The smooth end of the stovepipe fits over the cast
iron flue collar at top rear of stove (fig. 5).
a). Crimped end of pipe must be away from
stove.
b). Hand form lower end (fig. 6) of stove pipe to
oval shape (fig. 7) and slide over flue outlet collar
as shown in figure 5.
c). Secure stove pipe to flue collar with
at least three (3) sheet metal screws and seal with
stove cement.
2. Horizontal pipe runs must slope upwards
towards the chimney at least 1/4” per foot of hori-
zontal run.
3. You must have at least 18 inches of clearance be-
tween any horizontal piping and the ceiling.
4. The pipe cannot extend into the chimney flue (figure
8).
5. Secure pipe/elbow sections with three (3) sheet
metal screws at each joint to make the piping
rigid.
6. It is recommended that no more than two (2) 90
degree bends be used in the stovepipe installation.
The use of more than two 90 degree bends may
decrease the amount of draw and possibly cause
smoke spillage. Where possible, use only cor-
rugated (nonadjustable) elbows. These provide a
better seal.
7. The connector pipe must not pass through an attic
or roof space, closet, or any concealed space, or
floor, ceiling, wall or combustible construction. A
UL 103 HT Listed chimney must be used from the
first penetration of ceiling or wall to the chimney
cap. Never use single wall connector pipe as a
chimney - a house fire could result.
CORRECT WRONG WRONG
NOTE: STOVE PIPE IS NOT INCLUDED.
TO PURCHASE PIPE, VISIT YOUR LOCAL
HARDWARE, HOME OR BUILDING CEN-
TER. SEE “LOCATING STOVE” PAGE 4 FOR
ADDITIONAL SPECIFICATIONS.
CAUTION: KEEP FURNISHINGS AND OTHER
COMBUSTIBLE MATERIALS AWAY FORM THE
STOVE.
Fig. 5 – Flue Outlet Collar
Fig. 6 – Hand-form pipe to oval shape – Fig. 7
Fig. 8 – Stovepipe/Flue Connections

Page 6 / PB65XL VGZ-003 / 20110524.0
CHIMNEY CONNECTIONS
The stove must be connected to either a masonry
or manufactured metal chimney built and tested to the
specifications listed on the previous pages.
Chimneys perform two functions:
1). As a means of exhausting smoke and flue gases
which are the result of fuel combustion.
2). The chimney provides “draft” which al-
lows oxygen to be continuously introduced into the
appliance, so that proper combustion is possible. This
stove relies on natural draft to operate.
NOTICE: Always provide a source of fresh air
into the room where the stove is located. Failure to do
so may result in air starvation of other fuel burning
appliances and the possible development of hazardous
conditions, fire or death.
Your stove itself does not create draft. Draft
is provided by the chimney. To achieve proper draft
your chimney must meet the three minimum height
requirements detailed in figures 10–13. A minimum of
0.05 w.c. (measured in water column) is required for
proper drafting to prevent back puffing, smoke spillage,
and to maximize performance. (Gauges to measure draft
are readily available at stove stores and are economical
to rent or purchase.)
Factors such as wind, barometric pressure, trees,
terrain and chimney temperature can have an adverse
effect on the draft. The manufacturer cannot be held
responsible for external factors leading to less than
optimal drafting.
Should you have a problem with inadequate draft,
you should contact a licensed heating and cooling con-
tractor for assistance in solving the problem.
IMPORTANT Installation Points
1. Size chimney flue to stove collar. This stove
requires a 6” diameter flue.
2. Never connect this unit to a chimney serving
another appliance.
3. The chimney must meet all minimum height
requirements.
4. Never use a chimney to ventilate a cellar or
basement.
5. Contact your local building authority
for approved methods of installation and any
necessary permits and/or inspections.
MASONRY CHIMNEY
Before using an existing masonry chimney,
clean the chimney, inspect the flue liner and make
any repairs needed to be sure it is safe to use. Make
repairs before attaching the stove. The connec-
tor stove pipe and fittings you will need to con-
nect directly to a masonry chimney are shown in
figure 9.
Fig. 10 - Chimney Construction Through Attic Space
If the connector stove pipe must go through a
combustible wall before entering the masonry chimney,
consult a qualified mason or chimney dealer. The instal-
lation must conform to local building and fire codes and
latest edition of NFPA 211.
If there is a cleanout opening in the base of the
chimney, close it tightly.
CHIMNEY
FLUE
5/8" TILE
CHIMNEY
LINER
MASONRY
CHIMNEY
THIMBLE
COLLAR
6˝ ROUND
24 ga. BLACK
CONNECTOR
STOVEPIPE
8˝ MIN.
LINER
BELOW
ENTRY
HOLE
Fig. 9 - Masonry Chimney Connection

VGZ-003 / 20110524.0 PB65XL / Page 7
Fig. 11 - Chimney Construction Through Roof
Fig. 12 - Chimney Connection to Firebox
Through Masonry Wall
CHIMNEY CONNECTIONS continued …
MANUFACTURED CHIMNEY
REFER TO CHIMNEY AND CHIMNEY
CONNECTOR MAKER’S INSTRUCTIONS
FOR INSTALLATION AND USE.
Use only 6” diameter listed chimney UL 103
HT. Chimney made to this listing is High Tempera-
ture rated to 2100 degrees Fahrenheit. Use chimney
from only one manufacturer. Never mix brands.
Carefully follow the chimney manufacturer’s stated
requirements and clearances. Use the chimney
manufacturer’s attic guards, roof supports, flashing
and fire stops when passing through a ceiling. Use a
listed thimble when passing through a combustible
wall. Do not use makeshift compromises during
installation. Never use a single-wall connection
pipe as a chimney!
When using a pre-existing chimney, have it’s
condition and installation inspected before using.
Make sure that the chimney meets all of the UL
rating requirements listed above. Be aware that
not all manufactured chimney is of the UL 103
HT type.
NOTE: It is recommended that you contact a li-
censed heating and cooling contractor (consult your
local yellow pages) for chimney installation.
Manufactured chimney with the proper required
UL listing is available from most home centers,
hardware stores, and HVAC supply stores.
If you have access to the internet, you may
wish to view chimney manufacturers’ informa-
tion on-line. See, www.duravent.com, www.
selkirkinc.com, or www.mtlfab.com.
VENTING TO EXISTING FIREPLACE
In some instances, people desire to convert an
existing fireplace for stove use. Usually, safe con-
nection to an existing masonry chimney requires
more work than using a prefabricated chimney.
The existing fireplace must be closed and sealed at
the damper with high-temperature caulk, ceramic
wool, or furnace cement. Prior to installation, clean
and inspect the existing flue and smoke shelf. In-
stallation should be designed so the system can be
dismantled for periodic cleaning and inspection.
Before conversion, make sure the existing chimney
is structurally sound, the chimney incorporates a
flue liner and make sure it is in good condition.
(A flue liner consists of clay tile that protects the
brickwork of a chimney. If a chimney does not have
a liner, or it is damaged, have it relined by a profes-
sional. DO NOT USE a chimney that is unlined
or damaged!) If you have any question regarding
the condition of the chimney, consult a qualified
licensed contractor, qualified engineer, competent
mason, certified Chimney Sweep, or a knowledg-
able inspector. Consult your insurance company if
you cannot find a qualified expert.
Continued on next page

Page 8 / PB65XL VGZ-003 / 20110524.0
CHIMNEY CONNECTIONS continued …
CAUTION: Not all fireplaces are suitable
for conversion to a wood stove. Check
with a qualified expert.
Many prefabricated fireplaces are of the “zero-
clearance fireplace” category. These consist of
multilayered metal construction. They are designed
with enough insulation and/or air cooling on the
base, back and sides so they can be safely installed
in direct contact with combustible floors and walls.
Although many prefabricated fireplaces carry
endorsements from nationally recognized
organizations for use as fireplaces, they have not
been tested for connection to wood stove heaters.
Connecting a stove to such a device will void the
manufacturer’s warranty.
Steel-lined fireplaces are constructed with
1/4” firebox liner, an air chamber in connection
with 8” of masonry. These can be safely used with
wood burning stoves. They contain all the essential
components of a fireplace, firebox, damper, throat,
smoke shelf, and smoke chamber. Many look iden-
tical to masonry fireplaces and should be checked
carefully before connecting a stove to them.
Venting a stove directly into a fireplace does
not meet code and should not be attempted. (This
constitutes connection to another appliance - the
fireplace.) Combustion products will be deposited
and build up in the firebox or fireplace. The stove
warranty will be void with such an installation. Do
not create a hazard in your home by connecting in
this manner.
FIREPLACE INSTALLATION
Fig. 13 - Fireplace Conversion
Directly connecting the stovepipe into the exist-
ing masonry chimney (figure 12 “Type A” fireplace
conversion) of the fireplace is the only approved
method of installation. This is a complicated and
involved process and to insure safety should only
by done by a qualified installer.
1. An entry hole must be cut through the masonry
and tile liner with minimal damage to the liner.
At least 8” of liner must remain below the entry
position. When locating the stove and stove-
pipe, all minimum clearances must be observed
from combustible surfaces including mantels,
combustible trimwork, ceilings and walls.
Positioning the center of the stove pipe entry
into the chimney 24” below the ceiling should
insure proper clearance for a 6” stovepipe.
2. Install a metal or fire clay (5/8” minimum thick-
ness) thimble. Make sure the thimble is flush
with the inner surface of the chimney liner and
does not protrude into the flue (see figure 8 on
page 5).
3. Secure the thimble with refractory mortar. The
thimble should be surrounded by 8” of solid
unit masonry brickwork or 24” of stone.
4. Install the stovepipe into the thimble as far as
possible without extending past the flue lining
(see figures 10 on page 6).
5. A small airspace (about 1/2”) should remain
between the stovepipe and thimble to allow for
expansion of the pipe. Seal this airspace with
high-temperature caulking or ceramic wool.
6. Secure and seal the damper in the closed posi-
tion using high-temp caulking, ceramic wool,
or furnace cement. Also check to see if the
chimney has a cleanout. If it does, make sure it
is closed and sealed as well. A leaky cleanout
will greatly reduce draft efficiency.
If you have any questions regarding venting
your stove, contact the manufacturer or contact
the National Fire Protection Association (NFPA)
and request a copy of the latest editions of NFPA
Standard 211 and NFPA Standard 908. Their ad-
dress is:
Battery March Park, Quincy, MA 02269.

VGZ-003 / 20110524.0 PB65XL / Page 9
OPERATING INSTRUCTIONS
CAUTION: HOUSE FIRE HAZARDS
• DonotstorewooDorcoalonfloor
PROTECTOR, UNDERNEATH STOVEPIPE OR
ANYWHERE WITHIN MINIMUM CLEARANCES
FROM COMBUSTIBLE SURFACES SPECIFIED
FOR THIS STOVE. (36”)
• overfiring may cause a house fire.
YOU ARE OVERFIRING IF THE STOVE OR
CHIMNEY CONNECTOR GLOWS RED.
WARNING: EXPLOSION HAZARD
• neverusechemicals,gasoline,gas-
OLINE-TYPE LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID, OR SIMILAR
FLAMMABLE LIQUIDS TO START OR “FRESH-
EN-UP” A FIRE IN THE STOVE.
• Keep all flammable liquiDs, espe-
CIALLY GASOLINE, OUT OF THE VICINITY
OF THE STOVE — WHETHER IN USE OR IN
STORAGE.
OPERATING SAFETY PRECAUTIONS
1. STOVE IS HOT WHILE IN OPERATION. KEEP
CHILDREN, CLOTHING, AND FURNITURE AWAY
FROM HOT STOVE. CONTACT MAY CAUSE SKIN
BURNS. DO NOT TOUCH THE STOVE AFTER
FIRING UNTIL IT HAS COOLED.
2. NEVER OVERFIRE THIS STOVE BY BUILD-
ING EXCESSIVELY HOT FIRES AS A HOUSE/
BUILDING FIRE MAY RESULT.YOU ARE OVER-
FIRING THE STOVE IF STOVE OR STOVEPIPE
BEGINS TO GLOW OR TURN RED.
3. NEVER BUILD EXTREMELY LARGE FIRES
IN THIS TYPE OF STOVE AS DAMAGE TO THE
STOVE OR SMOKE LEAKAGE MAY RESULT.
4. PROVIDE AIR INTO THE ROOM FOR PROP-
ER COMBUSTION.
5. INSPECT STOVEPIPE EVERY 60 DAYS.
REPLACE IMMEDIATELY IF STOVEPIPE IS
RUSTING OR LEAKING SMOKE INTO THE
ROOM.
This stove is designed to burn
WOOD or COAL FUEL ONLY.
Hardwood, 16” to 10” should be split and air
dried (seasoned), for 6 months to obtain maximum
burning efficiency. Wood should be stored in a dry,
well ventilated area.
FOR BEST RESULTS WHEN BURNING COAL,
USE SOLID, BITUMINOUS COAL. NEVER USE
MANUFACTURED COAL “BRICKS” MADE OF
COAL DUST AND WAX-TYPE BINDER. DO NOT
BURN GARBAGE OR FLAMMABLE FLUIDS.
STORE COAL IN DRY, WELL VENTILATED
AREA.
LIGHTING
1. Open stove pipe draft damper fully to provide
maximum draft.
2. Fully open spin draft on ash door and keep spin
draft on feed door closed.
3,
USE WOOD OR COAL ONLY. Wood should be
seasoned (air dried) at least six (6) months after
cutting. Build six (6) small fires upon initial
firing.
4. Open the feed door and light wood or coal us-
ing several wads of crushed paper or a pile of
twigs in the firebox.
5. Lay small stacks of kindling on the paper to
start the fire.
6. Light the paper and kindling, close the door
and secure tightly.
7. After the fire has been started and is burning
satisfactorily, close slide draft almost all the
way.
8. Adjust spin draft on feed door to control rate
of burn to the desired level.
9. NEVER build extremely large fires in this type
of stove as damage to the stove or smoking may
result.
10. If you have too much draft, then regulate the
draft with the 6” stove pipe damper.
11.
DO NOT TOUCH – SEVERE BURNS
MAY RESULT!
After firing DO NOT TOUCH
STOVE until it has cooled.
12. This is a cast iron stove. It does NOT have
welded seams. From time to time you may
need to “refill and/or replace the stove cement/
mortar along the seams.
13. Adjust the draft damper and spin draft
control. The more closed the spin draft is set,
the lower and slower the fire will burn. The
Continued on next page

Page 10 / PB65XL VGZ-003 / 20110524.0
OPERATING INSTRUCTIONS continued …
more open, the faster and hotter the fire will
burn. Do not over fire the stove.
ADDING FUEL
Add small amounts of fuel each hour or so
instead of piling large quantities of fuel at one
time. This will insure a more complete combustion
process and less buildup of tars, soot, or creosote
will occur in the chimney.
1. Always open draft damper before opening the
feed door.
2. When adding fuel be careful not to smother the
fire.
3. Close the feed door and secure tightly.
4. Adjust the damper and spin draft controls.
5. Empty ashes regularly. Do not allow ashes to
pile up higher than the top of the hearth (see
Safety Instructions #14 page 2). If ashes build
up to the grate, burnout will occur.
6. Properly dispose of hot ashes (see Safety
Instructions, item #14 on page 2.)
7. Do not over fire the stove.
CAUTION: DO NOT OVERFIRE APPLIANCE.
TOO MUCH WOOD MAY CAUSE OVER FIR-
ING.YOU ARE OVER FIRING IF THE CHIMNEY
CONNECTORS OR STOVE GLOWS RED.
CLOSE THE DOOR, SPIN DRAFTS AND
DAMPER IMMEDIATELY TO REDUCE THE AIR
SUPPLYTOTHE FIRE.THISWILL SLOW DOWN
THE FIRE.
CAUTION: SLOW BURNING FIRES AND
EXTENDED USE MAY CAUSE EXCES-
SIVE CREOSOTE BUILDUP. IGNITION OF
CREOSOTE BUILDUP OR OVER FIRING MAY
CAUSE A CHIMNEY FIRE. CHIMNEY FIRES
BURN EXTREMELY HOT AND MAY IGNITE
SURROUNDING MATERIALS. IN CASE OF A
CHIMNEY FIRE LEAVE THE BUILDING AND
CALL THE FIRE DEPARTMENT FROM A SAFE
LOCATION.
MAINTENANCE & SERVICE HINTS
ASH DISPOSAL – Do not allow ashes to
accumulate higher than the grate. Dispose of
properly. (See Safety Instructions #13, page 2.)
CHIMNEY DRAFT – Draft is a function of
the chimney, not the stove — do not expect the
stove to draw. Smoke spillage into the house or
excessive buildup of condensation or creosote in
the chimney are warnings that the chimney is NOT
functioning properly. Correct the problem before
using the stove. Following are some possible causes
for improper draft.
1. The connector stovepipe may be pushed
into the chimney too far, stopping the draft.
2. If the chimney temperature is too cool,
water will condense in the chimney and run back
into the stove. Creosote formation will be rapid
and may block the chimney. Operate the stove at a
fire level high enough to keep the chimney warm
to prevent condensation from forming.
3. If the fire burns well but sometimes creates
excess smoke or burns slowly, it may be caused
by the chimney top being lower than another part
of the house or a nearby tree. The wind blowing
over a house or tree, falls on top of the chimney
like water over a dam, beating down the smoke.
The top of the chimney should be at least three
(3) feet above the roof and be at least two (2) feet
higher than any point of the roof within ten (10)
feet.
CREOSOTE – Formation and Removal.
Slow-burning wood produces tar and other organic
vapors which combine with expelled moisture to
form creosote. Creosote vapors condense in the
relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on
the flue lining. If ignited, this creosote creates an
extremely hot fire which may ignite surrounding
Continued on next page

VGZ-003 / 20110524.0 PB65XL / Page 11
MAINTENANCE & SERVICE continued …
STOVE JOINTS – Required Tune-up.
This stove is manufactured with cast iron
components. IT DOES NOT HAVE WELDED
SEAMS. Periodic “tune up” may be required by
refilling and/or replacing the cement/joint mortar
along the seams where the cast iron components
meet.
materials resulting in a building fire.
If creosote has accumulated, it should be
removed. Failure to remove creosote may result
in ignition and may cause a house/building fire.
Creosote may be removed using a chimney brush
or other commonly available materials from your
local hardware retailer.
CHIMNEY INSPECTIONS – The chimney
connector and chimney should be inspected at
the beginning of and at least twice a month dur-
ing the heating season to determine if a creosote
buildup has occurred.
Chimney fires burn very hot. If the chimney
connector should glow red, reduce the fire by
closing the damper and spin draft control and
immediately call the fire department.
CAUTION: A CHIMNEY FIRE MAY CAUSE
IGNITION OF WALL STUDS OR RAFTERS
WHICH WERE ASSUMED TO BE A SAFE
DI STAN CE F ROM T HE CH IM NEY. I F A
CHIMNEY FIRE HAS OCCURRED, HAVE YOUR
CHIMNEY INSPECTED BY A QUALIFIED
EXPERT BEFORE USING AGAIN.
A fire in the stove may be smothered by
pouring a large quantity of coarse salt, baking soda,
or cool ashes on top of the fire.

Page 12 / PB65XL VGZ-003 / 20110524.0
PARTS LIST – PB65XL RAILROAD POTBELLY STOVE
When ordering missing or replacement parts, always give the Model Number of the stove, Part
Number, and Part Description. Use the illustration and parts list provided to identify parts.
Part No. Description Qty.
1 Cook Lid ...................................................... 1
2 Lid Lifter....................................................... 1
3 Collar Top..................................................... 1
4 Top Plate...................................................... 1
5 Upper Chamber ........................................... 1
6 Feed Chamber............................................. 1
7 Feed Door.................................................... 1
8 Spin Draft..................................................... 1
9 Spring Handle.............................................. 1
10 Burn Chamber ............................................ 1
11 Shaker Door................................................. 1
Part No. Description Qty.
12 Shaker Grate ............................................... 1
13 Lower Chamber ........................................... 1
14 Base ............................................................ 1
15 Leg............................................................... 4
16 Ash Door...................................................... 1
17 Slide Draft.................................................... 1
18 Slide Draft Knob .......................................... 1
19 Ash Drawer .................................................. 1
20 Draft Damper (for pipe installation).............. 1
21 Hardware Pack (not shown)......................... 1

VGZ-003 / 20110524.0 PB65XL / Page 13

Page 14 / PB65XL VGZ-003 / 20110524.0
This Vogelzang heating appliance is safe when installed properly and will provide you with years of
service. However, always exercise good judgement when you are using this stove.You are dealing with
FIRE! Fire is inherently dangerous and must be treated with respect. Stay warm and in good health!
Respectfully yours,
Proprietor
Vogelzang International Corporation
400 West 17th Street
Holland, Michigan 49423
www.vogelzang.com
Phone: [phone]
Fax: [phone]
COMPANY TESTIMONY:
“FOR GOD SO LOVED THE WORLD THAT HE GAVE HIS ONLY BEGOTTEN SON, THAT WHOEVER
BELIEVES IN HIM SHALL NOT PERISH BUT HAVE ETERNAL LIFE”
JOHN 3:16
MADE IN CHINA
DO Not USE THIS STOVE IN A
MOBILE HOME, MANUFACTURED HOME,
TRAILER OR TENT — NO EXCEPTIONS!