Volkswagen 5C6.035.160 User manual

Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
5C6.035.160
Reference
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 1 of 78

Contents
1. Anti-theft coding
2. Factory Mode (code bypass mode)
3. Radio ON/OFF
4. Radio Volume Adjustment
5. FM/AM Operation
6. CD Operation
7. MEDIA Operation
8. CD-MP3 / USB / SD Card Play Operation
9. AUX Operation
10. BT AUDIO Operation
11. iPod Operation
12. Phone Operation
13. Audio / Setup
14. MFL key function short description
15. MFA indications
16. Climate indications
17. OPS indications
18. Diagnostic Mode
19. Engineering Mode
20. Software Update
Definitions
1.
2.
3.
4.
5.
6.
7.
LSM: Last Status Mode
Short Press: Press button less than two seconds.
Long Press: Press button more than two seconds.
In FM Band, when displaying 87.7, the receiver is tuned to 87.75 MHz.
In all the soft key buttons, there is a small triangle empty, in case to appear this triangle filled, it means that this
button/function/frequency has been activated/selected.
In case of short /long press SK buttons, the small triangle must be filled all of the time that SK button be maintain
pressed.
Regarding to the buttons: HK means Hard key; SK means Soft key,
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 5 of 78

1. Anti-theft coding
Role of radio coding
Removing the unit from the vehicle (for example, if you take your vehicle to the dealership for service and requires
disconnecting the battery) will be necessary to recode the radio manually. If you install the radio in another vehicle,
the recode also must be restored manually.
If SAFE appears in the display after turning on the radio, you can operate again only by entering the correct code.
Note:Thiscodenumber(4digits)iswrittenbyhandsonthelabelattachedontheradiowriting"****OK"
Turn on the radio, radio’s sound is muted. The display shows SAFE. After two seconds 1000 appears in the
display.
Use the SK [1 to 4] buttons to enter the numeric code. Use the SK [1] button to enter the first digit numerical
code. Use the SK [2] button to enter the second digit and so on. The range of values for each of the 4 digits is 0
to 9. The digits are increased by 1 to 1 every time you short press the SK buttons. The value returns to 0 after 9.
After entering the entire code, short press SK 6 [OK] button, radio output’s beep sound.
If the code has been entered properly, radio’s audio is started immediately and then goes to FM 1 band.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 6 of 78

Incorrect numeric code
If you have accidentally entered a wrong number, “CODE 1 SAFE” will appear blinking in the display, then “CODE 1
1000”. You can repeat the process again. The number of attempts will be displayed.
If you accidentally re-enter a wrong number again, “CODE 2 SAFE” will appear fixed on screen.
The unit will be blocked per 1 hour. Leave the radio power ON and Kl.30 and Kl.15 ON during that period. After about
an hour, you can repeat the process again.
Remember, the cycle is: 2 wrong attempts -> A lockout time.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 7 of 78

2. Factory Mode (code bypass mode)
In order to make it possible to check the unit and the periphery during the mounting at the assembly line, the unit can
be unlocked by pressing the combination of keys. That sequence can be repeated up to 50 times. The unlock unit can
play for a timeout of 15 minutes, after this time the unit locks again.
The first entering of security code will deactivate this factory mode feature.
This feature is available during radio delivery default condition with K.30 ON, regardless of the condition of the Kl.15
Activation:
Initial state: Radio OFF/ON, Kl.30 ON,
1. Press and hold right knob and then
2. Short press left knob
3. Display will show the numbers of factory modes used, then the radio frequency will appear in the display.
It is possible to have the Factory Mode deactivation with one of the following actions:
a. Switch radio off by pushing left knob once
b. automatic shutting off after operating time of the radio in bypass mode t = 15 minutes, regardless of the condition
of S-contact.
c. remove the battery power
d. activate of diagnosis mode via CAN message, radio switches to DIAG mode and upon terminating DIAG mode,
radio returns to bypass mode if still within 15 minutes of code-bypass operating time requirement, else radio goes to
“1000” state. If radio has not been decoded before, code bypass mode is still allowed if the number of times code
bypass used is < 50 times allowable limit.
e. activate of transport mode via CAN message, radio switches to low standby current mode and upon canceling
Transport mode, radio remains at low standby current mode or OFF mode. Upon power on, radio goes to “1000”
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 8 of 78

mode. If radio has not been decoded before, code bypass mode is still allowed if the number of times code bypass
used is < 50 times allowable limit.
f. activate of Phone mode via analog mute input or CAN message, radio switches to Phone mode and upon
terminating Phone mode, radio returns to current code bypass mode if still within 15 minutes of code-bypass
operating time requirement, else radio goes to “1000” state. If radio has not been decoded before, code bypass mode
is still allowed if the number of times code bypass used is < 50 times allowable limit.
g. radio power off by s-contact key via CAN message, upon power on, radio shows “1000” and can still access by
code bypass if the number of times code bypass used is < 50 times allowable limit.
h. automatically disable of code bypass mode after 50 attempts
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 9 of 78

3. Radio ON/OFF
Push left knob to switch radio ON/OFF.
Without ignition key inserted (Kl.30: ON, Kl.15 & Contact S: OFF), push left encoder may switch on radio to work per
30 minutes, after 30 minutes, radio will power off automatically.
Each time radio turns on, radio’s audio is started immediately (in the LSM) and user can do any adjustment.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 10 of 78

4. Radio Volume Adjustment
Rotating left knob may adjust radio volume level; radio will display the volume level bar per 5 seconds.
Rotate clockwise, increase radio volume; Rotate anti-clockwise, decrease radio volume.
For FM/AM modes: rotate the volume 0 will pause the music, so none additional function is allowed.
For CD, SD card, USB, IPOD and Bluetooth Audio modes: rotate the volume 0 will pause the music (and the CD
mechanism), so none additional function is allowed, muted speaker icon appears to the right in the upper line of
display; resume music playback when increases the volume again (Play will resume at the site of activation of the
pause), radio will display the volume level bar per 5 seconds.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 11 of 78

5. FM/AM Operation
5.1 Band Select
Non FM mode, short press HK [FM] button may switch to FM mode, short press again switch in order:
FM 1 => FM 2 => FM AS => FM 1.
In FM mode, if current station is stereo station, radio will not display “ST” characters.
RBDS must be ON all of the time, in case of station has a PS name, the display will show the Program Service name
(PS) and the frequency.
Non AM mode, short press HK [AM] button may switch to AM mode, press again switch in order: AM => AM AS =>
AM
5.2 Auto Store
Long press HK [FM] or [AM] button, radio will output’s beep sound and will search in the FM or AM frequency band
and the 6 strongest radio stations will be respectively stored into FM AS or AM AS band. Display will show
“STORING” during the process. The stations will store in the soft key buttons 1 to 6 since lower to higher frequency.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 12 of 78

If none station is found, radio will display “NO STATION" per 2 seconds and then returns to the frequency where the
searching started. In this case all memory presets remain as default defined.
If less than 6 stations are found via auto store, for example only 4 stations are found and stored to the soft keys 1~4
in the AS bands, the other soft keys 5 and 6 will be displayed as “- - -“ in the AS Bands.
If there are more than 6 stations active found, the radio must select the 6 best stations, they will be memorized from
frequency low to high, after all frequency in current wave band is covered once, auto store will be implemented and
play preset 1 in FM AS or AM AS band.
5.3 Initial Autostore
Long press more than 10 sec HK [FM] or [AM] button, radio will output’s beep sound and will scan FM band,
updates best FM station into all FM presets memories. Then scan AM band and updates strongest AM stations into
AM preset memories. Display will show “INITIAL AUTOSTORE” during the process. The stations will store in the soft
key buttons 1 to 6 since lower to higher frequency.
Function is repeatable for any number of times.
All presets have to be prepared with real stations.
Only as many memory locations as existing stations are filled starting with position 1.
If more than 6 FM and 6 AM stations are available, the 6 best/strongest stations have to be memorized in the FM AS
and AM AS bands respectively.
If the amount of existing stations is less then available presets, these stations would be copied in AM, FM1 and FM2.
In AM AS, FM AS band, these free stations are marked with “- - -“
Result 1 (example for an area with only 5 FM- and 3 AM-stations)
FM1: .................................. P1=f1, P2=f2, P3=f3, P4=f4, P5=f5, P6=f1.
FM2: .................................. P1=f1, P2=f2, P3=f3, P4=f4, P5=f5, P6=f1
FM AS: .............................. P1=f1, P2=f2, P3=f3, P4=f4, P5=f5, P6= - - -
AM:.................................... P1=f1, P2=f2, P3=f3, P4=f1, P2=f2, P6=f3
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 13 of 78

AM AS: .............................. P1=f1, P2=f2, P3=f3, P4= - - -, P5= - - -, P6= - - -
Result 2 (example for an area with only 2 FM- and 1 AM-stations)
FM1: .................................. P1=f1, P2=f2, P3 = f1, P4 = f2, P5 = f1, P6 = f2.
FM2: .................................. P1=f1, P2=f2, P3 = f1, P4 = f2, P5 = f1, P6 = f2.
FM AS: .............................. P1=f1, P2=f2, P3 to P6 = - - -
AM:.................................... P1=f1, P2 to P6 =f1
AM AS: .............................. P1=f1, P2 to P6= - - -
Result 3 (example for an area with only 8 (<12) FM- and 10 AM-stations)
FM1: .................................. P1=f1, P2=f2, P3=f3, P4=f4, P5=f5, P6=f6
FM2: .................................. P1=f7, P2=f8, P3=f1, P4=f2, P5=f3, P6=f4
FM AS: .............................. P1=f1, P2=f2, P3=f3, P4=f4, P5=f5, P6=f6 (the 6 best/strongest stations)
AM:.................................... P1=f1, P2=f2, P3=f3, P4=f4, P5=f5, P6=f6
AM AS: .............................. P1= f1, P2=f2, P3=f3, P4=f4, P5=f5, P6= f6 (the 6 best/strongest stations)
Result 4 (example for an area with only 17 FM- and 11 AM-stations)
FM1: .................................. P1=f1, P2=f2, P3=f3, P4=f4, P5=f5, P6=f6.
FM2: .................................. P1=f7, P2=f8, P3=f9, P4=f10, P5=f11, P6=f12
FM AS: .............................. P1=f1, P2=f2, P3=f3, P4=f4, P5=f5, P6=f6 (the 6 best/strongest stations)
AM:.................................... P1=f1, P2=f2, P3=f3, P4=f4, P2=f5, P6=f6
AM AS: .............................. P1= f1, P2=f2, P3=f3, P4=f4, P2=f5, P6=f6 (the 6 best/strongest stations)
By Initial Auto Store, for FM/AM AS level, the preset stations are completely same as by Auto Store.
For FM2, if the stations are =< 6, then FM1 is copied to FM2.
If the stations are > 6, then FM1 and FM2 are treated as one FM level.
If none station is found, radio will display “NO STATION" per 2 seconds and then returns to the frequency where the
searching started. In this case all memory presets remain as default defined.
If short press SK [- - -] button, radio will display “NO STORE” per 2 seconds and returns to LSM.
5.4 Frequency Store and Recall
Short press soft key button, may recall the preset station which stored in the button.
Long press soft key button, the current station will be stored into the button, radio will also output’s beep sound.
Default preset memory frequencies FM
Tuning
(MHz)
FM 1
FM 2
FM AS
Power
up
88.3
98.1
94.1
Soft
Key 1
88.3
87.9
88.3
Soft
Key 2
89.1
88.1
89.1
Soft
Key 3
94.1
98.1
94.1
Soft
Key 4
99.1
96.3
99.1
Soft
Key 5
106.1
107.9
106.1
Soft
Key 6
88.3
103.7
88.3
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 14 of 78

Default preset memory frequencies AM
Tuning Power Soft
Soft
Soft
Soft
Soft
Soft
(kHz)
AM
AM AS
5.5 Scan
Play
Up
530
1050
Key 1
530
530
Key 2
600
600
Key 3
1050
1050
Key 4
1400
1400
Key 5
1710
1710
Key 6
530
530
Enable scan play function with sort press HK button.
Radio will play the received station for 5 seconds then continue to seek for next available station.
After scan 1 cycle, radio will stop scan and revert to previous play mode.
Other mode to cancel the scanning is short press HK
station listening (playback remains in this received station).
button again during 5 seconds of received
Short press
last listened station.
or
buttons during seeking, radio will cancel the scanning and will tune the
Short press button during seeking, radio will cancel the scanning and will tune the next station.
SCAN indication is blinking each second in the display during the scanning.
5.6 Manual Tune
Rotating right knob may manually tune radio frequency.
Rotate clockwise, increase the frequency. Rotate anti-clockwise, decrease the frequency.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 15 of 78

5.7 Preset Stations List
Function not necessary.
5.8 Auto Seek
Short pressbutton, radio will search the previous or next available station, radio will
stop searching automatically and play the received station when it be found.
If none station is found, then returns to the frequency where the searching started.
5.9 Target Seek
button, the radio will decrease/increase fast the frequency, at momentKeep pressed
to release the button, radio will search the previous or next available station and play the received station.
Display will show the frequency upwards/downwards until the searching is stopped in a desired station.
If none station is found, then returns to the frequency where the searching started.
SEEK indication in the display is not necessary.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 16 of 78

6. CD Operation
6.1 CD insertion
At moment to insert CD, the display will show READING all of the time until radio is ready to play and then changes
to CD mode.
In case to insert a CD upside-down, CD damaged, dirty or with wrong type like CD Data, the display will show CD
ERROR per 2 seconds, the radio will eject this CD immediately and reverts to LSM
CD Mechanism pick up temperature > 85° degree, dis play OVER HEAT per 2 seconds, then revert to LSM.C
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 17 of 78

6.2 CD ejection
At moment to eject the CD, the display does not make any indication and radio goes to LSM.
The CD ejection must be possible without ignition key inserted (K15 and S-Contact signals OFF).
If nobody takes out the CD after 10 seconds, radio will insert the CD automatically without change to CD mode.
Radio is in FM mode and there is not a CD inserted, short press HK [
CD” per 2 seconds.
6.3 CD Mode Select
Non CD mode, short press HK [] button may switch to CD mode, the display will show READING all of
the time until CD mode is ready to play and then radio will resume playback of the CD inserted.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 18 of 78
] button, radio will display “NO

Radio is in FM mode and there is not a CD inserted, short press HK [CD] button, radio will display “NO CD” per 2
seconds, radio output’s beep sound then mode reverts to LSM.
6.4 Track Up/Down
Rotating right knob or short press left/right arrow button may select the previous or next track to play.
If current track play time <=3 sec, short press the left arrow button or rotate right knob anticlockwise by one step,
radio will play the previous track.
If current track play time >3 sec, short press left arrow button or rotate right knob anti-clockwise by one step, radio
will start to play from current track beginning.
6.5 Browse track list
Short press right knob to enter track list, radio will display all the available tracks (file names or titles).
The file, folder, title, or album name must be scrolled if name length is too large. Display will highlight the current
track playing (file name or title).
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 19 of 78

Rotate right knob may browse the tracks, short press right arrow button or right knob may play the track focused on
by the cursor (small filled triangle) and then radio resumes CD normal operation. Radio will display a slide bar if there
are more than 4 tracks in the CD.
Rotate the left knob may decrease/increase radio volume level, radio display remains without change (browse track
list), display will not show the volume bar.
60 seconds no action, short press left arrow button or long press right knob will exit the browse list.
6.6 Fast Forward/Rewind
Long press left/right arrow button may fast rewind or fast forward play the track, release button will cancel fast play
action.
Fast rewind operation in the first track of the CD must stop at the beginning of this track and resume CD normal
operation, otherwise fast rewind operation will continue in all the other tracks of CD.
Fast forward operation in the last track of the CD must stop at the end of this track and resume CD normal operation,
otherwise fast forward operation will continue in all the tracks of CD.
The sound must be continuous all of the time (no intermittent) and display will show fast the time during fast rewind
or fast forward playing.
6.7 MIX Play
Short press SK 3 [MIX] button, display will show the triangle filled next to MIX, it means MIX function has been
activated.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 20 of 78

Radio must play randomly all of the tracks in the CD, once all the tracks have been played, a new random track list
must be generated.
Short press HKbutton during MIX play, radio will advance the tracks randomly, the sequence is as
follows: random track => next random track => next random track => and so on, per example track 20 => 6 => 2 => 9
=> 13 => etc.
Short pressbutton during MIX play, radio will return only the previous track random and then the
sequence must be downward successively, the sequence is as follows: random track => previous random track =>
previous track => previous track => and so on, per example track 13 => 9 => 8 => 7 => etc.
Short press SK 3 [MIX] button again in order to deactivate this function, display will show the empty rectangle next to
MIX, it means MIX function has been deactivated.
6.8 Scan Play
Enable scan play function with HK button.
Radio will scan all of the tracks, each track will be played per 10 seconds, and radio will stop scan function after all of
the tracks have been played, in total one cycle. Per example, if scanning started in track 5 and CD has 20 tracks, the
sequence is as follows: track 5, short press SCAN button => track 6 plays 10 sec => track 7 plays 10 sec => … =>
track 20 plays 10 sec => track 1 plays 10 sec => …. => track 5 plays 10 sec => SCAN mode finished => track 6
normal play.
Other mode to cancel the scanning is short press
(playback remains in this track).
If current track play time 3 sec, short press
and will play the previous track.
If current track play time > 3 sec, short press
current track.
button during the 10 seconds of track playing
button during scanning, radio will cancel the scanning
button, radio will cancel the scanning and will play the
Short press
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
button, radio will cancel the scanning and will play the next track.
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 21 of 78

SCAN indication is blinking each second in the display during the scanning.
6.9 Repeat Play
Short press SK 6 [RPT] button, display will show the triangle filled next to RPT, it means REPEAT function has been
activated.
Radio will repeat the current track; it means if reach the track end, radio will play this same track from its beginning.
Short press [RPT] button again in order to deactivate this function, display will show the empty triangle next to RPT, it
means REPEAT function has been deactivated.
6.10 CD TEXT Information
In case to insert a CD TEXT, the display will show “INFO” additionally.
Short press SK 1 [
The default is title indication.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
] button to enter CD TEXT indication.
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 22 of 78

The radio will display the information in order: Title => Artist => Album => Title...
If the CD TEXT has not information, radio will not display any indication.
Each time short press INFO button will change according to the information showed, the title, artist or album name
must be scrolled if name length is too large, radio will display “TITLE, ARTIST or ALBUM” and show the triangle filled,
it means INFO function has been activated, after 15 seconds the information will revert to title indication and empty
triangle.
Prepared by Hector Gomez
HMI/ VWM DTEE / 52-222-2307414
DOC_HMI RADIO 2 DIN MIB-G LAM X1.8 revisada / 13/05/2011
Page 23 of 78