Volt VFL-450X-ABZ User manual
VOLT®Low Voltage Landscape Lighting
VOLT® 12V RGBW Flood Lights
VFL-450X-ABZ
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2021, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
- 1 -
INSTALLATION INSTRUCTIONS
www.voltlighting.com
- 2 -
Important: Please Read Before Installation
Important Safety Instructions
!
!
This luminaire is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instructions may
result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more
from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (transformer)
rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6
inches (15.2 cm) from a building structure, a luminaire or tting.
6. The main low voltage cable is intended for shallow burial - less than 6 inches
(152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage
lamp.
6. Do not operate the luminaire tting with a missing or damage shield.
SAVE THESE INSTRUCTIONS
VOLT®12V RGBW Flood Light
VFL-450X-ABZ
Package Contents
- 3 -
Product Dimensions
A. (1) Fixture Body B. IR Remote
7.25”
9.25”
5”
5.75”
R0.25”
R0.25”
9”
11.25”
8.25”
10”
3”
5”
5”
6.75”
8”
30 Floodlight
15W Floodlight
Ø0.75”
Ø0.75”
INSTALLATION INSTRUCTIONS
- 4 -
Marking for Expansion Bolt Anchors
1
Install Expansion Bolt Anchors
2
VOLT®12V RGBW Flood Light
VFL-450X-ABZ
Mark two points on the mounting
surface using the holes on the yoke
mount as a guide. These marks will be
used for the expansion bolt anchors (not
included).
Mounting
Surface
Hole
Fixture
Body
Yoke
Mount
Expansion Bolt Anchors
(not included)
Drill the proper holes using the
marks on the mounting surface for
the expansion bolt anchors. Insert
the expansion bolt anchors into the
drilled holes. Tighten the hex nuts on
the expansion bolt anchors until they
are fastened to the surface.
Mark
Mounting
Surface
Install Fixture Body
3
Remove the hex nuts and washers
from the expansion bolts. Attach
the yoke mount with xture body
to the bolts and secure with the
previously removed washers and
hex nuts. Tighten until snug.
Fixture Body
Bolt
Hex Nut
Washer
Mounting
Surface
Yoke
Mount
- 5 -
Wire Connection
4
Strip both leads from the xture pigtail. Using two wire connectors(sold
separately), connect the leads from the xture bodies to the main
supply cable leads.
Pigtail
Supply Cables
from Fixture Body Wire Connectors
Main Supply Cable
Adjust Fixture Body
5
Fixture Body
Screw
Wrench
Using the wrench, loosen the
screws on the side of the xture to
adjust the xture to your desired
orientation. Always tighten the
screws after any adjustments.
- 6 -
INSTALLATION INSTRUCTIONS
VOLT®12V RGBW Flood Light
VFL-450X-ABZ
Install Stake
1
Stake Mount
Determine the desired location
for mounting the stake. Hammer
the stake into the ground until
ange of stake is ush to grade.
To avoid damage to the stake,
place a board on top of the stake
while hammering.
Note: If the ground is hard and
the stake is dicult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake
Install Fixture to Stake
2
Attach the coupler onto the
stake. Place the yoke mount
with the xture body onto the
coupler and secure with the hex
nut. Hand tighten until snug.
Fixture
Coupler
Yoke
Mount
Hex Nut
Ground
Soil
Stake
- 7 -
Wire Connection
3
Pigtail
Main Supply Cable
Wire Connectors
Main Supply Cable
Supply Cables
from Fixture Body
Strip both leads from the xture pigtail. Using two wire connectors(sold
separately), connect the leads from the xture bodies to the main
supply cable leads.
Adjust Fixture Body
4
Fixture Body
Screw
Wrench
Using the wrench, loosen the
screws on the side of the xture to
adjust the xture to your desired
orientation. Always tighten the
screws after any adjustments.
INSTALLATION INSTRUCTIONS
VOLT®12V RGBW Flood Light
VFL-450X-ABZ
An IR Remote is suitable for this xture. Please refer to the following
instructions for usage and battery replacement.
IR Remote
Remove Plastic Film
1
CR2025
RELEASE
OPEN
PUSH
Remove the plastic lm from
the IR remote before use.
Backing
Plastic Film
IR Remote
Remove
- 8 -
IR Remote Functions
2
OFF
FLASH
FADE
STROBE
SMOOTH
ON
R G B W
2 1
3
4
5
6
7
1. On/O
2. Brightness Control
3. 16 color selections
4. Flash
ZMode 1: Repeats Red, Green, Blue + color cycle for 1 second duration of
each of the seven colors within this mode.
ZMode 2: Hit ash a second time and this mode slowly blends the same
seven colors from mode one, mixing them together.
5. Strobe
ZMode 1: Pick any color on the remote, then press strobe and that color
will strobe every second alternating between on and o.
ZMode 2: Hit strobe a second time and this mode will strobe a blended
white color at the same speed as before.
6. Fade
ZMode 1: Pick any color on the remote, then press fade and that color
will slowly fade in and out every second.
ZMode 2: Hit fade a second time and it will fade a blended white color
in and out at the same speed as before.
7. Smooth
ZMode 1: Repeats a ash cycle of Red, Green, and Blue only.
ZMode 2: Hit smooth a second time and this mode slowly blends Red,
Green, and Blue only; in and out of each other at the same speed.
NOTE: When using the
remote make sure it is
pointed at the sensor in
the faceplate so it operates
properly.
- 9 -
INSTALLATION INSTRUCTIONS
VOLT®12V RGBW Flood Light
VFL-450X-ABZ
- 10 -
Replace Battery
3
CR2025
RELEASE
OPEN
PUSH
Push the side of the battery
bracket and carefully remove
it from the IR remote. Replace
the battery and then insert the
battery bracket back into the IR
remote.
Replacement Battery Style:
CR2025 Button Battery
PUSH Battery Bracket
Battery
REMOVE/
INSERT
Backing
IR Remote
- 11 -
INSTALLATION INSTRUCTIONS
Specications and product details subject to change without notice.
© Copyright 2021, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3700
IS-VFL-450X-ABZ-ver1
- 12 -
Table of contents
Other Volt Floodlight manuals
