Voltex AMP User manual

Power Supply
Operating
Temperature
Relative
Humidity
LED
Indication
230V AC,50 Hz, Approx 4VA
0°C To 55°C
Up to 95% RH Non Condensing
Kilo Ampere Reading
Model
Size (mm)
Display
Panel Cutout
Input Current
96(H) X 96 (W) X 45 (D) mm
3 Digit/Line 7 seg 0.56”,red LED Display
92 X 92 mm
AMP
0.5 to 5AMP AC, (PRIMARY) CAT III
Protection
Level
(As per request)
IP-65 (Front side) As per IS/IEC 60529 : 2001
www.voltexcontrols.com
Page - 1
AMP
Connection Diagram
CT RATIO SELECTION
OPERATING MANUAL
3 Phase Panel Meter
AMP
Technical Specification
AMP
.
.
.
1) Press & Hold the scroll key for 5 sec.
4) IF no key is press for 5 second CT Ratio Automatically SAVE & EXIT.
5) From 5 to 100 CT Ratio increased by step 5 AMP
From 100 to 1000 CT Ratio increased by step 25 AMP
From 1000 to 2000 CT Ratio increased by step 50 AMP
From 2000 to 6000 CT Ratio increased by step 500 AMP
3) Press scroll key to change the CT Ratio, up to  display B will
show the CT Ratio, from  to  amp Display Y & B thought
will show the primary CT Ratio.
2) Display R will show  (CT Ratio) and Display Y & B will show the
Primary CT Ratio (Y-most significant digit, B last three digits)
LN
S1
R
Y
B
S2 S2 S2
S1 S1
12347 8 9 10
56
230V AC
50Hz, 4VA
!
Accuracy Class:1.0
Current: 0.5 To 5A AC, CAT III
Range
CT Selection up to 6000/5 Amp AC CAT III

AMP
www.voltexcontrols.com
Page - 2
All safety related codifications, symbols and instructions that appear in this operating manual
or on the equipment must be strictly followed to ensure the safety of the operating personnel as
well as the instrument.
If all the equipment is not handled in a manner specified by the manufacturer, it might impair the
protection provided by the equipment .
Product improvement and upgrade is a constant procedure. So for more updated operating information and support,
contact our Helping : 70 46 319 319 or Email at [email protected]
=> Read complete instructions prior to installation and operation of the unit.
WARNING : Risk of electric shock.
3) Cable used for connection to power source, must have a cross section of 1mm or greater. These wires
should have insulations capacity made of at least 1.5kV.
2) To reduce electro magnetic interference, use wire with adequate rating and twists of the same of
equal size shall be made with shortest connection.
4) When extending the thermocouple lead wires, always use thermocouple compensation wires for wiring
for the RTD type, use a wiring material with a small lead resistance (5Ω max per line)and no resistance
differentials among three wires should be present.
1) To prevent the risk of electric shock power supply to the equipment must be kept OFF while doing the
wiring arrangement. Do not touch the terminals while power is being supplied.
5) A better anti-noise effect can be expected by using standard power supply cable for
the instrument.
Warning Guidelines
Mechanical Installation
Safety Precautions
1) Prepare the panel cutout with proper dimensions as show above.
2) Fit the unit into the panel with the help of clamp given.
3) The equipment in its installed state must not come in close proximity to any heating source,
caustic vapors, oils steam, or other unwanted process by products.
4) Use the specified size of crimp terminal (M3.5 screws) to wire the terminal block. Tightening the
screws on the terminal block using the tightening torque of the range of 1.2 N.m.
5) Do not connect anything to unused terminals.
2
A
B
C
D
EF
MODEL A
96mm 96mm 92mm 92mm 3mm 42mm
BC
D E F
DIMENSIONS
136mm - 5.35 inches
120mm - 4.72 inches
AMP
.
.
.