VOLTRIUM Offroader Series User manual

Offroader Series
Suitable For:
Rogue Dual Motor
Rogue Dual Motor Max
Owner's Manual

Hi, it's Jeff & Daniel here, the founders of Voltrium. We'll be popping up throughout this
manual when we have a pro tip or valuable insider information to share about our scooters!
Congratulations on your brand new
Voltrium and thank you for supporting the
only brand in Australia that designs and
engineers their products locally.
It has been an absolute pleasure involving
Australian industry and clever minds locally
to bring the Rogue Dual Motor series to life
We hope everytime you hop on for a ride
you can feel the passion behind our team
Because to us at Voltrium, it's more than just
a scooter.
CONGRATULATIONS
AND THANK YOU!

Voltrium Offroader(Max)
Charger
Seatpost & Saddle
Accessories (If optioned)
Emergency Toolkit
INSIDE THE BOX
Pro Tip: Use this checklist and tick the boxes as you remove the packaging to ensure you have received everything.
Woohoo! You have received the scooter. Now let's unbox it and hit the paths.

Pro Tip: Remember to insert safety pin back into the folding mechanism. If the pin does not fit,
the scooter hasn't fully unfolded. Simply repeat unfolding process again with more force
Let's Unfold the scooter, it's as easy as 123
GETTING STARTED
Remove the Rogue Offroader scooter
from the box.
Remove the Safety Pin from the
folding mechanism
Push the folding lever downwards
towards the footboard, whilst pulling
the steering column in the opposite
direction to unfold the scooter.

Pro Tip: You may find that some switchgear or brake levers require tilting forwards / backwards to suit your
height. There are hex bolts on each handlebar component that can be loosened to allow adjustments
Now, we'll attach the handlebars
GETTING STARTED
Remove the 4 bolts holding the top
half cap of the handlebar clamp.
Once the half cap is removed, place
handlebars onto the clamp, ensuring
it is centred and oriented correctly.
Once the alignment and positioning
of the handlebars are correct, reinstall
the top half cap with the 4 bolts to
secure the bar.

Pro Tip: If the seat still moves or slides up and down with the quick release clamp engaged, it has not been
wound tight enough. It's a good idea to check the saddle too, to ensure the nuts are wound tight enough.
Attaching the Seat
GETTING STARTED
Offroader: Insert Seat pole into the
socket
Offroader Max: Insert the seat base
through the slits of the foot board.
Push forward until seat locks into the
two side tabs. Fasten the rear knob to
secure seat.
Attach Saddle to Seatpost. There are 2
nuts to tighten each side of the
saddle's clamp. Tighten evenly.
Release quick release clamp, lift seat
to desired height. Wind the clamp
until tight. Re - engage the quick
release clamp to set.

Pro Tip: The connectors only plug in if the orientation is correct. Look for the arrow on the
female and male connectors, once they line up the connector will go in.
Attaching the headlights
GETTING STARTED
Dual Motor: Attach Single headlight
to the headlight bracket
Dual Motor Max: Attach Dual
headlight Assembly to headlight
bracket
Connect the headlight(s) to the
scooter's wiring harness. There will be
vacant plugs coloured red that will
extend to the headlight(s) vicinity.
Take care to ensure the arrows on the
female & male connector line up
before plugging in.

Pro Tip: You will get most of your battery range within the first 2 hours of charging. For
maintenance, keep the battery topped up to maximise battery life.
GETTING STARTED
Locate the charge port on the side of
the scooter. Open the cap.
Locate the charger. Plug the 3 prong
end into the scooter charge port.
There will only be 1 orientation the
plug will engage.
When the RED and GREEN LED's are
illuminated, the scooter is charging.
You should hear the cooling fan spin
up.
Once the RED LED is turned off, the
scooter is fully charged.
Charging the scooter

Charge Scooter - Until the charger shuts off and illuminates green light
PRE-RIDE CHECKS
To ensure you get the most of your first ride, follow this checklist:
Check Tyre Pressure - Ensure front and rear are at 40psi
Ensure all nuts and bolts are tight on the scooter.
Adjust steering column and or seat to a comfortable height
Familiarise with the controls of the scooter.

Check with your local State or Territory regarding specific laws governing the use of personal mobility devices
(PMD). States and Territories have different laws in place that can prohibit the use of a Voltrium Scooter
LEGALITIES &
PRECAUTIONS
Have fun. Responsibly.
Do not ride in a manner that will endanger yourself and surroundings. High Performance riding should only be
performed on private property
Always ride whilst wearing safety gear. Failing to do may result in severe penalties with local authorities and or
serious injury / death.