Vossloh-Schwabe Blu2Light LiNA Connect User manual

1
Operating Manual
LiNA Connect / LiNA Touch
Programming the Blu2Light System
Using LiNA Connect
Operating the Blu2Light System
Using LiNA Touch

2
TABLE OF CONTENTS
1General Notes......................................................................................................................3
1.1 Legal notice...................................................................................................................3
1.2 Downloading the APP ....................................................................................................3
2Preperation ..........................................................................................................................4
3How to create a simple system ..............................................................................................5
4Using an automation ..........................................................................................................21
5setting up the tunable white function ....................................................................................23
6implementing a DigiLED (186839) + manual configuration .................................................26
7Daylight control Explained ..................................................................................................30
8How to use Motion detection ...............................................................................................32
9using Sequences.................................................................................................................35
10 add and use Timers.........................................................................................................38
11 using the Air Sensor ........................................................................................................42
12 using the Blu2Light Relais ................................................................................................46
13 using the B2L Connect PB4 ..............................................................................................48
14 Including an Blu2Light Repeater.......................................................................................50
15 Do’s and don’ts ..............................................................................................................51
15.1 Do’s ........................................................................................................................51
15.2 Don’ts .....................................................................................................................52
15.3 Informal...................................................................................................................53

3
1GENERAL NOTES
Thank you for choosing the Vossloh-Schwabe Blu2Light system. Prior to using the product, please
read this operating manual to familiarise yourself with the system's functions.
Any person tasked with system setup, commissioning, operation, maintenance and repair must be
•suitably qualified and
•closely observe the provisions of this operating manual.
1.1 Legal notice
Trademarks
•The Vossloh-Schwabe and the Blu2Light logos are trademarks of Vossloh-Schwabe
Deutschland GmbH.
•Other products and company names mentioned in this manual may be trademarks of other
companies.
Copyright
© Copyright 2022 by Vossloh-Schwabe. All rights reserved. Without the prior written consent of
Vossloh-Schwabe, no part of this document may be reproduced or transmitted in any form or using
any means, be they electronic or mechanical; nor may photocopies or any other kind of record be
made, nor may any system for information storage or restoration purposes be used.
1.2 DOWNLOADING THE APP
Both apps are available as iOS and Android versions in the respective app stores.
LINA Touch LINA Connect

4
2PREPERATION
Make sure that all your Blu2Light nodes are powered and that the QR codes of the nodes are ready,
for example stuck on your floor plan!
Figure 1

5
3HOW TO CREATE A SIMPLE SYSTEM
Open the LiNA Connect app and click on the (+) in the lower right corner to create a project, then
name your project and create a system with the same procedure. Now scan the desired QR code by
pressing the (+) again!
Green = everything is ok.
Figure 2

6
Figure 3
Orange = already used in another system

7
Figure 4
Except for a gateway, you have the options "Name", "Power On Behavior" and "Properties"
furthermore you can choose the color for every node which it should be displayed in, this helps with
the overview in big Projects and also looks fancy!

8
Figure 5
Select "Switch on with last state" in the "Power On Behavior" tab.
Figure 6
Now the node uses the last state as Power On behavior after power was cut off
(works only for 10.000 cycles).

9
Figure 7
Select a node and select "Express Setup" to start automatic setup.

10
Figure 8
A rotating circle at "DALI addressing" indicates an active DALI search.

11
Figure 9
If the DALI search is completed, all DALI devices should be displayed, and a functional group should
have been created.

12
Figure 10
Now you can create scenes according to your wishes, "50%", "Off" and "On" are the most common
ones.
Figure 11

13
Figure 12
The master dimmer must always contain a value since it is accessed during a scene action.

14
Figure 13
If all scenes are configured as desired, only thing left is to generate a user interface in the Touch
App, for that, switch to the tab "LiNA Touch".

15
Figure 14
Here you can select an interface via the (+), depending on the scope of the desired functions.
Unused touch panels will not be displayed in the LiNA Touch app, if more touch panels are needed,
fields can always be added.

16
Figure 15
Each control panel must now be assigned a function that can later be used in the Touch App.

17
Figure 16
Once this is achieved, your user interface should look something like this.
Figure 17
Now the control panels are assigned to the respective functional groups and (Figure 18) to the
respective scenes via the event configuration using drag & drop.

18
Figure 18
Figure 19
In the last step, press and hold the respective touch profile you want to export in the main window of
the Connect app and select "Export". Now you are free to scan the generated QR code with another
device using the LiNA Touch app or to export it in another way by pressing "Share".

19
To scan the QR code, press the QR code symbol in the upper right corner of the LiNA Touch App
and scan the respective QR code.
Figure 20

20
Figure 21
Congratulations!
Your basic system is now fully operational and can be operated via the Touch App!