Voxx CA2LED5 User manual

1ca2LED5 / FLRS 4280849 Owners rev A.
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
PROFESSIONAL
SERIES
Owner’s Guide
For Model:
CA2LED5
Flashlogic FLRS
RF Upgrade Kit

22017 Voxx Electronics Corporation. All rights reserved.
Table of Contents
Using Your Remote Control .......................................................3
Remote Start Valet Mode............................................................4
 2WayTransmitterNotications ................................................5
Transmitter Programming..........................................................5
 ReplacingRemoteControlBatteries ........................................6

3ca2LED5 / FLRS 4280849 Owners rev A.
Using Your Remote Control
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the button one time will unlock
only the driver’s door. Press again within three seconds to unlock the remaining
doors.
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, pressing and holding the button for 3
seconds will open the vehicle’s trunk or hatch.
Door Lock
To lock the vehicle doors press and release the button.
Door Unlock
To unlock the vehicle doors press and release the button.
Remote Starting Your Vehicle
To activate the remote vehicle start function, press and release the button 2 times
within 2 seconds.
Using the Personal Protection Alarm (Panic) (Optional)
Press and hold the button for 3 seconds to activate the personal protection alarm.
To stop the alarm, press and hold the button on the transmitter again for 3
seconds.
Remote Start Shutdown
Press and hold the button for 3 seconds to turn the vehicle off. Pressing the
vehicle’s brake will also shutdown the remote start.

42017 Voxx Electronics Corporation. All rights reserved.
Remote Start Valet Mode
Enter / Exit Valet mode for systems using an Flashlogic FLRS kit.
1. Cycle ignition ON ve times [5x OFF/ON] rapidly. (complete this step
within 7 seconds)
2. Wait, LED 1 (on the FLRS kit) will turn solid RED for 2 seconds.
3. Turn ignition to OFF position.
4. Valet Mode Programming Procedure completed.
NOTE: In Valet Mode, the Remote starter is not functional. On units with Keyless
Entry, Lock and Unlock will remain functional. To exit valet mode: repeat steps 1 to 4.
Entering the Vehicle while it is Running via Remote Vehicle Start
1. Unlock the vehicle’s doors.
2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3. Insert the key into the ignition switch and turn to the ON or RUN
position.
4. Press the brake pedal. The remote vehicle starter will disengage and
the vehicle will operate normally.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and
operation. After the system starts the vehicle, the heater or air conditioner will
activate and heat or cool the vehicle’s interior to your setting.

5ca2LED5 / FLRS 4280849 Owners rev A.
2 Way Transmitter Notications
  FUNCTION   BEEPS/LEDFLASHES
Lock 2 Beeps / Flashes
Unlock 1 Beep / Flash
Trunk Release 1 Beep / Flash if vehicle is currently locked.
Remote Start Activation 1 Beep / Flash
Conrm Remote Start 4 Beeps / Flashes
Remote Start Running 1 Flash per 5 seconds for duration run time
Remote Start Shutdown 3 Long Beep / Long Flashes
Car Find / Panic 1 Beep / Flash
Low Battery 2 Flashes when button is pressed
Transmitter Programming
1. Turn the ignition ON.
2. Press and hold the valet/override button located on the antenna.
3. Within 10 seconds the LED’s will begin to ash.
4. Press 1 button of each transmitter you wish to program, the LED’s will
ash to conrm each transmitter.
5. Turn the ignition OFF
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.

62017 Voxx Electronics Corporation. All rights reserved.
 ReplacingRemoteControlBatteries
4 Button Remote Control - Model CAT4M
The battery inside each remote control should last approximately 1 year under normal
use. When the battery becomes weak you will notice the remote control range (the
distance from the vehicle the remote control will work) deteriorate and the small LED on
the remote control will dim. To replace the remote control batteries:
1. Remove 1 screw then disassemble the halves of the remote
control by unsnapping the back of the case.
2. Remove the old battery, observing the +/- symbols on the
batteries and replace with a new battery.
3. Reassemble the halves of the remote control and reinstall 1
screw.
4. Test operation of the remote control.
2 Way LED Remote Control - Model CATMLED
The battery inside the 2-way LED remote control should last approximately 6 months
under normal use. When the battery becomes weak you will notice the remote control
range (the distance from the vehicle the remote control will work) deteriorate and give an
additional ash upon button presses. To replace the remote control batteries:
1. Using a coin, disassemble the halves of the remote
control.
2. Remove the old battery, observing the +/- symbols on the
batteries and replace with a new battery.
3. Reassemble the halves of the remote control
4. Test operation of the remote control.

7ca2LED5 / FLRS 4280849 Owners rev A.

82017 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation.
Customer Service 1-800-421-3209
WWW.CODE-ALARM.COM
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.