Voyager Dock Titan Bench User manual

PARTS LIST DESCRIPTIONPART NUMBERQTYITEM 4" CUP HOLDER (GREY)HD-0011621 ARMRESTVM-015-1322 ARMREST SUPPORTVM-015-1423 11/4CAPPLUGHD-0011224 3/8 X 1 SS CARHD-0005985 3/8 BRASS FLANGE NUT
HD-0005686 #10-3/4 OVAL HEAD SCREW SSHD-0015747 1/4 X 5/8 SS FLAT WASHERHD-000671685/16 X .688 SS FLAT WASHER
HD-0007849 1/4-20 X 1-3/4" HCS S/SHD-00094810 SS ACORN NUT 1/4HD-00095811 5/16-18 X 2.5" HCS BOLTS S/SHD-00063412 5/16-UNC NUT S/SHD-00080413
Titan Bench
DOCK RAIL
6
6
6
5
7
2
7
1
PAGE 1
1
3

3/8X1S/SCARRIDGEBOLT (8REQ'D) 3/8FLANGENUTBRASS(8REQ'D)
PAGE 2
1/4-20 X 1 3/4 HCS BOLTS S/S (8 REQ'D) 1/4" ACORN NUT S/S (8 REQ'D)
1/4X5/8FLATWASHERS/S(16REQ'D) 1.25 CAP PLUG (2 REQ'D)
56
10 11
4
8

#10.75" OVAL HEAD SCREW SS (4 REQ'D)
7
5/16 WASHERS (S/S) (4 REQ'D)
5/16 NUTS (4 REQ'D)
5/16-18 X 2.5" HCS BOLTS S/S (4 REQ'D)
ARMREST SUPPORT (2 REQ'D)
12 13
9
3
PAGE 3
ARMREST (2 REQ'D)
2

PAGE 4
1
4" CUP HOLDER (2 REQ'D)

To insure your safety while assembling your Voyager product:
Fully read and understand the assembly instructions
Do not assemble this product if items are missing or damaged
Wear protective gloves, clothing and eye wear when assembling this product
Installation procedure
The following tools will be needed : 2- 9/16” wrenches, 2- ½” wrenches, phillips screw
driver.
1. Install 1 ¼” caps into the top of bench leg frames. Per diagram B.
2. Attach titan tread assembly’s to bench leg frames (for bench seat and backrest) using ¼”
x 1 ¾” bolts. Per diagram C.
3. Tighten bolts for seat and backrest with 2 -7/16” wrenches.
4. Attach armrest support tube to bench with 2- 5/16” x 2 ½ ” bolts, washer and nut. Per
diagram D.
5. Tighten armrest bolts with 2 - 1/2” wrenches.
6. Using phillips screws and screw driver attach armrest to armrest support tube. Per
diagram E.
7. Repeat steps 4-6 for second armrest.
8. Insert head of 4- carriage bolts into raceway on the underside of the rail and slide to
desired location on dock. Per diagram A.
9. Hook bench into side of dock rail and slide carriage bolts into brackets. Finger tighten
nuts at this time. Per diagram F.
10. Put carriage bolt into raceway on the side of dock, slide into bench bracket and install
flange nut. Per diagram G.
PAGE 5

11. Repeat step 10 for remaining 3 carriage bolts.
12. Use 9/16” wrench to tighten all 8 mounting bolts (carriage bolts).
13. Insert cup holder into armrest.
PAGE 6

RACEWAY
Diagram A
PAGE 7
Diagram B
4
7
Diagram C
11
8
8
11
8
78
11
88
11
88

5
55
6
6
6
6
Diagram D
Diagram E
PAGE 8
13
9
12
Diagram G