VS Sassoon Metro Cordless HairCut VS704A User manual

Model VS704A
METRO CORDLESS HAIRCUT

IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are
present, basic safety instructions should always be followed,
including the following:
Polythene bags over product or package may be dangerous. To
avoid danger of suffocation, keep this wrapper away from babies
and children. This bag is not a toy.
DANGER: When the unit is used in a bathroom, unplug it
after use since the proximity of water presents a hazard
even when the unit is switched off.
WARNING: Do not use this appliance in or near bathtubs, showers,
basins or other vessels containing water.
• Do not immerse in water or other liquids. .
• Do not reach for an appliance that has fallen into water. Unplug
immediately.
• Take care to avoid contact between the moving blades of the
unit and the skin, paying particular attention to the face, neck
and hands.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance

IMPORTANT: Always unplug the appliance when not in use or
before cleaning. Do not leave unattended when plugged in or
switched on. Do not place on any heat sensitive surface and always
allow to cool before storing away.
• Do not use any attachments other than those supplied by Conair
Australia Pty Ltd.
• Do not use the appliance with damaged or broken attachment
combs or with any teeth missing from the blades, as injury may
occur.
• Use this appliance only for its intended use as described in this
instruction booklet.
• This appliance is not intended for commercial use.
• Do not place appliance on any surface while it is operating.
• Do not use outdoors or operate where aerosol (spray) products
are being used or where oxygen is being administered.
• Never drop or insert any object into any opening
• Do not use the appliance if it is damaged. In the event of
damage, discontinue use immediately and contact your dealer for
instructions on returning it for examination or exchange.
• Always ensure that the voltage to be used corresponds to the
voltage marked on the unit.
• For additional protection, the installation of a residual current
device(RCD) with a rated operating current not exceeding 30mA
is advisable in the electircal circuit supplying the bathroom. Ask
your installer for advice.

METRO CORDLESS HAIRCUT
The VS For Men Metro Cordless Haircut is a rechargeable cordless
hair clipper with a high performance motor and sharp blades. With
10 comb cutting lengths from 3mm to 25mm including left and
right ear guides and a range of grooming accessories, the Metro
Cordless Haircut clipper is the most convenient way to keep you
looking good.
3
5
9
8
10
7
6
2
1
4
Features:
1. 8 cutting guides for hair
+ 2 ear contours guides
(left/ right)
2. Blades: large 39mm blades
3. OFF/ON/Turbo switch
4. Charging indicator light
5. Turbo function
6. Oil
7. Cleaning brush
8. Comb
9. Scissors
10. Storage pouch

INSTRUCTIONS FOR USE
CAUTION, THIS APPLIANCE DOES NOT OPERATE WHILE ON THE
MAINS AND SHOULD BE CHARGED BEFORE USE.
To guarantee battery autonomy and life, charge the batteries for
16 hours before using for the first time and then approximately
every three months.
Before any use, recharge the appliance for 16 hours, ensuring the
power switch is in the ‘OFF ’ position and that the charging indicator
light is lit.
A full charge will allow a minimum of 30 minutes of use of the
clippers.
Never charge the unit for periods longer than 24 consecutive hours
and only use the charger provided.
Before Use:
Always inspect the appliance to ensure the clipper head is free from
hair, etc. and is running smoothly. Failure to do this can result in
injury.

COMB GUIDE ATTACHMENTS
The appliance is supplied with 10 comb cutting lengths from 3mm
to 25mm including left and right ear guides. The comb guides are
marked with the following grade number:
Grade 1 = 3mm
Grade 2 = 6mm
Grade 3 = 9.5mm
Grade 4 = 13mm
Grade 5 = 16mm
Grade 6 = 19mm
Grade 7 = 22mm
Grade 8 = 25mm
Left Ear Guide = LEFT
Right Ear Guide = RIGHT
USING THE CUTTING GUIDES
To attach a comb guide and to remove it, ensure the appliance is
switched off.
• To attach it, position the comb guide over the front of the clipper
blade and slide over the head. Push and click the rear of the comb
guide into position (Fig. 1).
• To remove it, push the tab on the rear of the comb guide away
from the head and lift off (Fig. 2).
Fig. 1 Fig. 2

BEST CUTTING PERFORMANCE
1. Ensure the clipper head is free from hair and other debris.
2. Use on clean, dry hair that has been combed until tangle-free.
3. The person whose hair is to be trimmed or cut should be seated
so that the top of their head is at your eye level.
4. Attach the appropriate comb guide attachment as required. If
using more than one grade, start with the longer first.
5. Switch the clipper on.
6. Hold the clipper against the hair, with the teeth of the clipper
pointing upwards, yet flat against the head.
7. Move the clipper upwards and outwards through the hair, a
little at a time clipping against the direction of the hair growth.
8. The clipper will work most efficiently when cutting through the
hair at its own speed. Never force the clipper.
9. Never switch the clipper off whilst in the hair.
SUGGESTED HAIR CUTS
FOR LONGER HAIR ON TOP OF THE HEAD
Use the barber comb to lift the hair on top of
the head and use the Clipper to cut across the
top of the comb. Alternatively, hold the hair
between the fingers and cut to desired length,
always working from the front, to the back
of the head. Gradually cut the hair shorter by
reducing the space between the comb or fingers
and the head (Fig. 3). Comb often to check for
uneven strands and to get rid of trimmed hair. Fig. 3

OUTLINING THE HAIR
Outlining requires no attachments.
Comb hair into the desired style.
Position the Clipper between the
sideburns and ear, making sure the
corner edge of the blade is against the
hairline. With the outline of the hair
as your guide, slowly move the Clipper
over, around and behind the ears
(Fig. 4). For the back of the neck and the sideburns, hold the Clipper
upside down, holding it against the skin at the length desired,
move theClipper downwards (Fig. 5).
CREW CUT
Always cut from the back of the neck to the crown,
using the longest comb setting. Hold the comb
attachment flat against the head and slowly move
the Clipper up through the hair (Fig. 6). Use the
same technique for the sides, cutting from the
bottom to the upper side of the head. For the front
crown, cut the hair against the direction in which it
grows. Then even it up with the sides.
FLAT TOP
Use the barber comb and simply cut the hair on
top of the head by running the Clipper over the
barber comb (Fig. 7). To taper the hair down to the
neckline, use the 3mm attachment comb. Comb
the hair to remove any loose cut hair and check
for uneven spots. Then outline the sideburns and
the neck area (see ‘Outlining’).
Fig. 6
Fig. 7
Fig. 4 Fig. 5

CLEANING AND MAINTENANCE
To ensure long lasting performance of your clipper, clean the
blades and unit regularly.
After each use, clean the clipper as follows:
1. Remove the comb guide after use. Rinse under running water
and dry thoroughly before storage or use.
2. To make cleaning easier, the clipper blades can be removed.
Make sure the clipper is turned off. Hold the clipper with the
blades pointing up and remove them by pressing the top of the
blade. (Fig. 8)
3. Using the cleaning brush, brush and blow away any remaining
hair.
4. After cleaning, switch the appliance on, and oil the blades by
adding a few drops of the oil supplied over the blades. Only
use the lubricating oil supplied with this appliance as this is
specifically formulated for high speed clippers and does not
evaporate or slow the blades.
5. To clean the clipper unit, wipe with a damp cloth and dry
immediately.
6. Do not use any liquid cleaners or harsh corrosives on the clipper
unit.
IMPORTANT – Never place the blades under running water, as this
can ruin the cutting performance of the blades. Always use the
cleaning brush to clean the clipper head and blades.
Fig. 8

BATTERY DISPOSAL
The appliance contains Nickel Metal-Hydrate batteries. To protect
the environment, the appliance must be disposed of safely at the
end of its useful life. Please take the appliance to a recycling centre,
where the internal rechargeable battery should be removed by a
professional and recycled separately.
For more information about the recycling of electrical and battery
operated appliances, please contact your local council office or
your household waste disposal service.
Ni-MH