VTI 10200 User manual

Handle shelf section assembly parts
Upper pole
Lower pole Horizontal mount
Vertical mount
WARNING: Please keep
the TV mounting screws
M5, M6, M8, M10 and the
L key in a secure location
as they may be required
for use with the flat panel
TV at a later time.
Model: 10200

Top
Bottom
Leg"O"
Leg"X"
1.
Lay front legs (labeled "O" and "X") on the floor with the brackets
facing upward and inward as illustrated. Note: legs,when placed
on the floor should bend upward, off the floor at their top end and
the width of the unit should remain constant all the way to the top.
2.
Slide each shelf over the brackets of the legs. The largest shelf is
the bottom. The top shelf has the VTI decal on it.
3.
Slide the two remaining legs onto the shelves as illustrated. Make
sure that the brackets are inside the shelves.
4.
HAND TIGHTEN the top, middle and bottom shelves at the two
corners with square head bolt, washer and nut (see screw table I)
as illustrated. Please make sure washer and nut are together on
the inside of the leg bracket.
Page 2
Leg "X"
Leg "O"
Top Middle Bottom
Leg"O"
Leg"X"
Back of shelf
Front of shelf

Page 3
7.
Hand-tighten the upper
pole (with holes) to the
lower poles.
Upper pole
Lower pole
5.
In order to have the unit properly
aligned, stand unit upright on a
level surface. Gently rock unit
back and forth to realign and
level the unit.TIGHTEN ALL
NUTS AND BOLTS WITH
WRENCHES AT THIS TIME.
Unit should now be properly
aligned and level. If unit is not
level at this time, repeat the
above steps before proceeding
to step 6.
8.
Insert the two support
poles onto the top and
middle shelves as shown.
6.
Lay unit on the floor. Align the holes on the casters with
the holes on the corner of the bottom shelf. Use
the hex screws (see Screw
table F) and tighten
the caster. Repeat
the same for the
other three casters.
It is recommended
you place the locking
casters on either the
right side or left side of
the unit for safer and
easier movement of cart
through doorways, ect..

Page 4
10.
Tighten the two
supporting poles
onto the bottom
shelf with two
screws as shown
(see screw table M).
9.
Insert the two horizontal
mounts onto the support
poles. Note: The mount with
adjustable screw(see screw
table H) should go on the
bottom. Screw(see screw
table G) the top mount to
desired height from A to F.
Adjust the bottom mount
height according to the TV
screw position later.
Top horizontal mount
Bottom horizontal mount
12.
Unscrew the screws from
the legs (see screw table J).
Align the holes on the bracket
of the handle shelf with the
holes on the legs of the cart,
tighten the screws.
11.
Handle shelf assembly
Unscrew the screws from
handle bar, handle support
bar and handle rail (see
screw table K & L). Align
the holes on the handle
bar with the holes of the
handle rail, the holes on
the handle support bar with
the holes of handle rail, the
holes on the shelf with the
holes of the handle rail,
tighten the screws as
shown.
L-hand side HandleRail
Handle support bar
Handle bar
Shelf
R-hand side Handle Rail

Page 5
13.
Electrical bracket assembly instruction
A. Push power cord into cord
winder bracket.
B. Attach electrical bracket
to back side of top shelf
with two nuts and bolts
(see screw table E).
Tighten nuts and
bolts securely.
Wrap power cord
around wings of
the bracket.
Electrical
bracket
Bolts
16.
Congratulations!
Unless you have also
purchased the optional
laptop shelf or web.
cam. platform, you
have completed the
installation of
Model 10200.
14.
Use the appropriate screws needed (M5, M6, M8 or M10, see
screw table M5x12, M6x12, M8x16 or M10x16) to fasten the flat
panel TV onto the vertical mounts as shown.
15.
Hook the vertical mount onto the top
horizontal mount. Align the vertical mount
with the top horizontal mount, fasten the
vertical mount onto the horizontal
mount as shown. Align the bottom
horizontal mount with
the vertical mount,
fasten the horizontal
mount onto the poles.
Use the screw to
fasten the vertical
mount to the bottom
horizontal mount as
shown.