VUEROID D10-FW Series User manual

D10-FW Series
Quick Start Guide
V1.0 English
The product is a dashboard camera.
Make sure to understand the contents of the manual to use the product correctly.
D10-F2W
D10-F2Wi
D10-FH3W

Precautions Before Using the Product
Key Features
Warning
Caution
Do not expose this product to rain, moisture or water under any circumstances,
doing so may result in the risk of electric shock or 󽗉re.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in this instruction unless you are quali󽗉ed to do so. Please make sure
to have the unit serviced by a quali󽗉ed service technician if you are facing with
some cases as follows;
1. The unit has been exposed to rain or water.
2. The unit does not seem to operate normally.
3. The unit shows a marked change in performance.
VUEROID does not warranty any defects that can be caused by owner’s fault
VUEROID is not responsible for any damaged that occur while driving.
FHD DUAL
Support up to
3CH
FOV 146°
CMOS
Image Sensor
Prevent
Discharge
ADAS Option
Time Lapse
External Wi-Fi
Option
Format Free
Night Vision
External GPS
Option

Package Contents
Dashcam Mount
Quick Manual
12V Power Cable
Rear View
Camera
Rear View
Camera
IR In-Cabin View
Camera
IR In-Cabin View
Camera
Hardwiring Cable
(3m/9.8ft)
Micro SD Card
Rear View Camera
Cable (6m/19.6ft)
Rear View Camera
Cable (6m/19.6ft)
SD Card Adaptor & Case
Wind Shield Tape
Y-Cable
Common Components
D10-FH3W Components
Option
D10-F2Wi ComponentsD10-F2W Components

Mark Description
❶EXT port Used to connect the external Wi-Fi
❷GPS Port Used to connect the external GPS
❸CAM1 Input Port Used to connect the 2CH camera or Y-Cable for 3CH
❹DC-IN Power Port Used to connect the power cable
❺Speaker Speaker for voice guidance
❻Mount Installation Mount
❼Camera Lens Front camera for video recording
❽Power Switch Power ON/ACC/OFF switch
❾MIC Microphone for voice recording
❿Memory Card Slot Insert a memory card
⓫Status LED Indicate the recording status
⓬LCD Touch screen LCD
❺
Product Overview
❾
⓫
⓬
❷ ❸❶
❻
❼
❹
❽
❿

Device Installation
Caution
1. Main Device Installation
- Make sure to install the device in a safe area and that the engine is OFF.
-
Please check if the Micro SD card is inserted correctly before connecting to power.
- Make sure the installation area is clean.
- Unplug the DC power if you are not using the device for a long period of time.
- Do not drop the product as it may not function properly.
- During extreme high temperatures or hot weathers, parking indoors is
suggested.
(1) Select and clean the area where the product will be installed.
(2) Remove the Wind Shield tape 󽗉lm.
(3) Attach the device.
(4) Connect the Rear Camera or In-Cabin Camera, and connect the power cable.
To avoid interrupted reception with other devices such as a navigation,
make sure the wiring is not overlapped with enough space in between.
[For D10-FH3W] Connect the Y Cable to CAM1 Port.
Connect Rear Camera to (L) port and In-Cabin Camera to (R) port.
1
3
2
4
⚠
⚠

2. Connecting Hardwiring Cable
3. Rear View Camera Installation
Caution When Inserting Micro SD Card
-
Do not apply excessive force on the Micro SD card or insert in the wrong direction.
Any actions which may cause an SD card error, will be the responsibility of the user.
- Please test the Micro SD card for errors frequently and because it is a consumable
item, it should be replaced periodically.
- Make sure the device is turned o󽗈 when you pull out the SD card.
- Any issues arisen by using a di󽗈erent Micro SD card besides VUEROID’s are the
responsibilities of the user.
- Store important recordings into other devices (ex, PC).
(1) Select and clean the area where the product will be installed.
(2) Remove the Wind Shield tape 󽗉lm.
(3) Connect the rear view camera and connect the power cable.
Before installation, make sure the engine is turned o󽗈.
Make sure the installation area is cleaned.
Make sure the installation area doesn’t interfere with the window’s
infrared rays.
Please visit a professional installer
to connect hardwire cable.
1 32
BLACK : GND
YELLOW : BAT (B+)
RED : ACC
⚠
⚠
⚠
⚠

Product Spec
Product Speci󽗉cations
General Speci󽗉cations
Item Description
Camera
CIS
Front : FHD 2M (1920 x 1080 @ 30fps)
Rear : FHD 2M (1920 x 1080 @ 30fps)
In-Cabin (D10-F2Wi) : FHD (1920 x 1080 @ 30fps)
In-Cabin (D10-FH3W) : HD (1280 x 720 @ 30fps)
View Angle
Front : (D)146° x (H)116° x (V)90°
Rear : (D)134° x (H)105° x (V)80°
In-Cabin : (D)125° x (H)98° x (V)62°
LCD 3.5” LCD / Resistive touch (480 x 320)
Memory Card Micro SD Card (16GB / 32GB / 64GB / 128GB / 256GB)
Wi-Fi / External Cable
with USB Dongle External antenna
LED Indicators Rear : Security LED
G-Sensor 3-Axis Acceleration Sensor, +2g / -2g
Speaker Built-in Speaker (Voice Guide)
Microphone Built-in Microphone
Video Codec H.264 High Pro󽗉le
Recording Mode Normal / Event / Manual / Parking (Motion & Time lapse)
Dimensions
Front : (W)97mm x (H)64.5mm x (D)31.6mm
Rear : (W)52mm x (H)29mm x (D)42mm
In-Cabin : (W)47.6mm x (H)27mm x (D)33.7mm
Weight Front : 114.5g / Rear : 28g / In-Cabin : 52g
Power Input DC 12V ~ 24V
Power consumption Max. 4.0W at 12V
Operating Temp. -20°C ~ 70°C (-4°F ~ 158°F)
High Temp. Cut-o󽗈 Approximate 70°C (158°F) / Battery Discharge Prevention
Item Description
Certi󽗉cations FCC, CE, ROHS, RCM
Software IOS & Android compatible mobile app
Window & Mac compatible PC viewer

Frequently Asked Questions
Q1. Is it possible to use the product regardless of types of cars such as a
passenger car or a commercial vehicle?
The product for both 12V and 24V can be used regardless of types of cars.
Q2. What is a low voltage prevention function (vehicle battery discharge)?
The product is embedded with a low voltage prevention function. It is available to
set voltage values through environment setting. If the voltage of a vehicle drops
below the set value, the power of the product is turned o󽗈 automatically.
Q3. No impact has occurred but a video 󽗉le is saved in an event folder.
The product detects impacts through a G sensor of the dashcam. An impact is
saved in an event folder when the product detects shaking of a vehicle going over
a speed bump or in other situations. It is possible to adjust the sensitivity of the G
sensor (an impact sensor) through environment setting.
Q4. I cannot not turn on the power.
Check if the power cord is connected properly. If it is connected properly, check
the status of the battery. The lifespan of a fuse may be expired. If a problem is not
solved even after the fuse is replaced, contact the customer service. ([e-mail])
Firmware update
Full Manual / Firmware, Download is available on the VUEROID website.
http://www.vueroid.com/support/downloads
Warrenty Information
All dashcams sold from VUEROID include a 1 year manufacturer warranty (6 months
for SD card).
The warranty does not apply to the following
1) Cosmetic damage, such as scratches, and dents
2) Damage caused by accident, abuse or natural disaster.
3) Damage caused by service performed by anyone who is not an authorized service
provider of VUEROID
4) Damage to a product by not using supplied power or accessories in the package.
http://www.vueroid.com

Note : Status Bar is always displayed and is located at the bottom of the
screen so that the driver can easily check it when mounted on a vehicle.
Screen Layout
1. Main Screen
2. STATUS BAR
❺ ❻ ❼❹❸❷
❶
❶
Manual
Recording
Press to start manual videos
recordings up 30 Sec (10 sec
prior, and 20 sec afterward)
❷ HDR
HDR On
HDR O󽗈
❸ GPS
GPS is Not Connected
GPS Signal is Lost
Receiving GPS Signal
❹
Camera
Channel
Front Camera Recording
Front + Rear Camera
Recording
❺ ADAS
ADAS is On
ADAS is O󽗈
❻ Audio
Audio Recording is On
Audio Recording is O󽗈
❼
Recording
Mode
Continuous Mode
Recording
Parking Mode Recording
Event Mode Recording
Manual Mode Recording

❶Audio Recording Audio recording turn On / O󽗈
❷Volume Control Speaker Volume Low / Mid / High / O󽗈
❸Play List Recording video list
❹Setting View the con󽗉gure the dashcam Settings
❶Menu Press the Menu button to enter the dashcam’s Menu system
3. Menu
4. Menu Screen
❶
❹❸
❷❶
< Normal Mode > < Secret Mode >

5. Play List
❶Drive
Drive recordings are saved.
Recorded videos are saved in
1 minute segment with an
auto-looping mechanism.
❷Parked
Park recordings are saved. Max
30 seconds of recording 󽗉les
including motion / impact event
recordings are saved.
❸Event
Event-triggered videos are saved
in 30 seconds, from 10 seconds
before detection to 10 seconds
after detection.
❹Manual
Manual recordings videos are
saved in 30 seconds, from
10 seconds before manual
recording button is pushed to
20 seconds after.
❶View Mode Switch between video
preview and list view
❷List Up Move to the beginning of
the list
❸Page up Move to the page up
❹Page Down Move to the page below
❺List Down Move to the end of the list
❶Play / Pause Play / Pause a video
❷Previous Play previous video
❸REW Rewind a video
❹FF Forward a video
❺Next Play next video
❺
❹
❸
❷
❶
❹
❸
❷
❶
❺❹❸❷
❶

6. Settings
Setting Menu Tree:
See below for the settings to be found
under each submenu
ADAS
You can Enable or Disable a lane departure warning system (LDWS), a Front Vehicle
Start Alarm (FVSA), a Forward Collision Warning System (FCWS), a Rear Collision
Warning (RCW), and set their options.
Safety Camera Alert
When the vehicle approaches or passes the speed limit zone, the safety camera
alert system will Collect GPS signals and safety camera data. Refer to the following
instructions to enable or disable this feature.
Download will be available on the VUEROID website (http://www.vueroid.com/support/
downloads).
❶ Recording
1) Continuous recording
mode
2) Video Quality
3) HDR
❷Parking
Mode
1) Parking recording mode
2) Discharge cut-o󽗈 voltage
3) Discharge cut-o󽗈 time
❸
Event
Sensitivity
1) Impact sensitivity in
continuous mode
2) Impact sensitivity in
Parking mode
3) Front motion sensitivity
4) Rear motion sensitivity
❹ADAS
(*Available
with GPS)
1) LDWS
2) LDWS Sensitivity
3) FVSA
4) FCW
5) RCW
❺Memory 1) Memory allocation
2) Format
❻System
1) LCD operating time
2) LCD brightness
3) Rear view camera display
4) Security LED
5) Time setting
6) System information
7) Secret Mode
❺ ❻❹
❸❷❶

Using Wi-Fi Application
1. Wi-Fi Application Download and Installation
2. Wi-Fi Application Registration
Search “VUEROID Dashcam” on the App Store (iPhone), Play Store (Android) then
install.
Turn on the “Wi-Fi” button on the dashcam.
Then it shows a SSID (VUEROID_D10-FXX_XXXXXX) on the list of Wi-Fi network.
(1) Tap on “OK” once the pop-up screen is shown and it says “Connect to device”.
(2) You’ll be greeted by a SSID in the form of VUEROID_D10-FXX_XXXXXX in a given
Wi-Fi network listing.
Tap on that SSID and key in a default PW(12345678).
1 2
(*Available with Wi-Fi)

❺
❷
❶
❹❸
❻
❶Wi-Fi Status Display Wi-Fi status and the
name of the connected device.
❷Wi-Fi Connect Enable or Disable Wi-Fi
connection.
❸Live Viewer View the front / rear live stream.
❹File Viewer Find the recording 󽗉les in
di󽗈erent folders.
❺History
(*Available with GPS)
Find the trip data and travel
route by dates.
❻Setting Allows user to get unit’s settings
switched.
❶Left / Right
Reverse
Switch to Left / Right viewing
image.
❷Snapshot Capture the display image.
❸Full Screen Display the full screen.
❹
CH
(Front / Rear /
In-Cabin)
Switch to Front / Rear / In-Cabin
camera image.
❺ADAS
(*Available with GPS)
Initialize the ADAS calibration
setting. Enable or disable
following fuctions
1) LDWS
2) FVSA
3) FCW
4) RCW
5) Safety camera Alert
3. Wi-Fi Application Start-up Screen
4. Live View Mode
❺
❹❸
❷❶

❶Drive
Drive recordings videos are saved. Recorded
videos are saved in 1 minute segment with an
auto-looping mechanism.
❷Event
Event-triggered videos are saved in 30 seconds,
from 10 seconds before detection to 20 seconds
after detection.
❸Parked
Park recordings videos are saved. Max 30
seconds of recording 󽗉les including motion /
impact event recordings are saved.
❹Manual
Manual recordings videos are saved in 30
seconds, from 10 seconds before manual
recording button is pushed to 20 seconds after.
❺Phone Recordings videos saved in the smart phone are
saved.
5. View the Recordings (File Viewer)
The recording 󽗉les in the D10 unit can be viewed
through the File Viewer. Each folder support the
thumbnail view with front / rear options.
Yours Itineraries can be safely stored in the History
Menu so that you can access all your previous car
rids.
Plus, Travel-log drive will help drivers or 󽗊eet
managers to 󽗉nd a vehicle’s current Location using
the VUEROID Mobile app. Captured by the VUEROID
Built-in antenna, the vehicle’s location, speed, and
direction of travel is shown in the mobile app on a
Google maps display.
❺❹❸❷❶
6. GPS Mapping within the App

Using Desktop Software
1. Download PC Viewer
2. PC Viewer Compatibility
3. Start PC Viewer
Open the Internet browser then download the PC Viewer on the following link in
below.
http://vueroid.com/support/downloads
The PC viewer is compatible for Windows OS computers.
Open the installed VUEROID D10 Viewer on the desktop.
Before opening the viewer, make sure the Micro SD card is inserted.