VUPplus FOLDABLE CYCLING BACKPACK User manual

NB-8233
Cycling Backpack with LED Signal Light
User Manual
www.vupplus.com
FOLDABLE CYCLING BACKPACK
www.vupplus.com [e-mail]
Miracle Intelligent Technology Co., Ltd.
4/F,Bldg 1,Launch Industrial Park, Wuhe Avenue,
Bantian Shenzhen,518129 China
Made in China

Preface: Thank you for using cycling backpack with led
warning signal light and sensor. In order to use and
maintain this product correctly, please fully read the user
manual before using. This product is specially designed for
the safety of people who often cycle at night. The warning
led signal light, realized by means of the operation of
remote controller, will indicate your next intention and alert
others behind/around you to achieve the goal of safety.
Special Instructions:
1. The led signal lights are just for the purpose of alerting
people behind/around you, can not be treated as traffic
signal lights.
2. This product also applies to other outdoor exercises such
as Hiking, Jogging, etc.
3. For any statements below, all rights are reserved by
VUP+
What this package contains:
1 One backpack
2 One LED displayer
3 One remote controller with plastic mount
4 One micro-USB cable
5 One cable with micro-USB connector on both ends
6 One user manual
Parts Illustration
1
3
4
7
8
5
6
On/off button
1
9
2
LED signal light
2
3Cycling signal
4Right-turning signal
5Left-turning signal
6Caution signal
7RC(remote controller) button
8Plastic RC mount
9Backpack
01 02

Transmitter
Battery: 250mAh rechargeable Lithium battery (directly
plug into USB power adapter to charge)
Working time: 20 hours
Shell material: PC+ABS+ Silicon
Specification
Wireless frequency: 2.4GHz
Transmission distance: 3-5meters (depending on the actual
surroundings)
Receiver
Battery: 3.7V, 1150mAh rechargeable Lithium battery
(directly plug into USB power adapter to charge)
Working time: continuously 8 hours
Charging: DC 5V 500MA
Backpack:
Material: Nylon
Product Size: 17” x 12” x 4.6”
Weight: 365g
Certificates
FCC, IC, CE, ROHS
User Instructions:
Receiver：
Power on: press the switch(Part ), four different LED
signal lights will be on one by one as below, and then into
stand-by mode. It won’t be activated until remote
controller is on.
Power off: press the button(Part ) while they’re working
normally, LED signal lights will go off immediately.
Power on: push the button(Part ) to the backward, three
different (forward/left/right) LED signal lights will be on in
about 5 seconds, lose it, and it’s okay to use. Meanwhile,
LED displayer’s power-on signal lights will be on once
again.
Transmitter:
1
1
7
03 04

Remote controlling mode: Left arrows will be on when
you slide RC to the left direction, and vice verse.
White cycling-shape LED signal lights will be on when you
push up RC. Red triangle LED signal lights with exclamation
mark inside will be on when you press down RC. The LED
signal lights on RC are totally in line with those on LED
displayer
A: Cycling Signal: White cycling-shape LED signal lights, means
you’re cycling
B: Left-turning Signal: Left arrows, means you’re going to turn left
C: Right-turning Signal: Right arrows, means you’re going to turn right
D: Caution Signal: Red triangle LED signal lights with exclamation
mark inside, means you want to stop or the road condition is not
good, people behinds you should pay more attention.
A
BC
D
Power off: push the button(Part ) to the backward while
they’re working normally, LED signal lights will go off in
about 5 seconds
How to make it work?
Step one: switch on the LED displayer
Step two: power on the remote controller
Step three: good to go with remote controlling mode &
auto-induction mode
7
06
05

How to install & remove remote controller
How to install:
Every transmitter and receiver is originally matched with a
special identity, and can be re-matched by learning mode
when it doesn’t work properly.
How to operate?
First, switch on the transmitter and receiver separately, and
then connect them with specially made cable with
micro-USB connector on both sides(as below), push RC to
any direction, if the signal on LED displayer keeps the
same pace, then the learning mode is done.
32
2
1
1
How to remove:
Learning Mode (Rematch mode):
Loose RC mount Fix RC mount on handle bar Clip on
Auto-induction mode: realized by the sensor built in the
transmitter, only available for two signals: cycling signal &
caution signal.
Additional statements:
Remote controlling mode has the priority over auto-induc-
tion mode. The operation system will change to
auto-induction mode 7 seconds after any working signals
except caution under remote controlling mode. If you push
down RC, it’ll remain caution signal all the time and won’t
change to other states until you push RC to other directions.
07 08

1.Q: No red signal lights are on when you push RC to the
backward?
A: Probably the device runs out of battery, you’d better
charge RC
2.Q: Still not working when RC finished charging
A: Try to re-match RC & LED displayer, if still don’t work,
then contact local service.
FAQ
The product is 1year warranted against defects in
materials and workmanship. If product found to be
defective, we will repair or replace at no charge. Damage
due to misuse, abuse or wear and tear is not covered by
warranty. Warranty time is 12 months after date of
shipment.
Warranty policy
How to charge
Micro-USB cable to Charge
Fully-charged indicator(Blue)
Power Capacity indicator,<30%(Red)
Charging indicator(Red)
Fully-charged indicator(Blue)
Power Capacity<30%/Power on(Red)
Charging indicator(Red)
09 10

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference
that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
English: "
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that
may cause undesired operation of the device."
French:"
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes :
(1) l'appareil nedoit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
11 12
FCC STATEMENT: