W Box Technologies 0E-HDMIEXTDR User manual

1
Introduction
Congratulations and thank you for purchasing W Box Technologies
0E-HDMIEXTDR.
0E-HDMIEXTDR is an HDMI extender over a single Cat5e/6 cable.
It is capable of transmitting full 1080p HD video, HD audio and
bi-directional IR control together up to 130ft.
It features EDID DIP switch on transmitter and EQ DIP switch on
receiver in the event of installation difficulties. The extender
provides affordable, high quality HDMI signal transmission solutions
for your audio/video and IR control needs.
Please follow the instructions in this manual to assure proper
installation and to achieve the full performance and satisfaction you
would expect from W Box Technologies.
Features
Easy to use, one pair as a full functional module
HDMI and Bi-directional IR pass through
1080P@60Hz up to 130ft over a single Cat5e/6 cable
Built-in ESD and surge protection
HDMI 1.3a and 3D formats compliant
Supports HDMI or DVI inputs
Bi-directional IR control
Transfers IR control signal together with the HDMI signal

2
Package Contents
Before you start the installation, please check the package contents:
1 x0E-HDMIEXTDR
2 x 12V 0.5A DC Power Supply
1 x IR Emitter
1 x IR Receiver (30-50KHz)
2 x Mounting Brackets (Pair)
1 x User Manual
1 x Datasheet

3
Panel
Transmitter
Front Panel
12
ID.
Name
Description
1 Power On: Indicates that the transmitter is powered
on.
2 Status
Solid On: When both status LEDs in
transmitter and receiver turn solid on, it
indicates that the network is active and
video can be shown on the display.
Rear Panel
123 4 5 6
ID.
Name
Description
1
Power
12V 0.5A DC power supply input
2 VIDEO
OUT Connects this RJ45 port to the receiver via a single Cat5e/6 cable for video output.

4
ID.
Name
Description
3 IR OUT Connects to an IR emitter
4 IR IN Connects to an IR receiver (30-50KHz)
5 HDMI IN Connects to an HDMI source
6 EDID Adjusts the EDID for outputting the desired
video resolution.

5
Receiver
Front Panel
12
ID.
Name
Description
1 Power Solid On: Indicates that the receiver is
powered on.
2 Status
Solid On: When both status LEDs in
transmitter and receiver turn solid on, it
indicates that the network is active and
video can be shown on the display.
Rear Panel
1 2 3 4 5 6
ID.
Name
Description
1
Power
12V 0.5A DC power supply input
2 VIDEO IN Connects this RJ45 port to the transmitter
via a single Cat5e/6 cable for video input.
3
IR IN
Connects to an IR receiver (30-50KHz)
4 IR OUT Connects to an IR emitter
5
HDMI OUT
Connects to an HDMI display
6 EQ Adjusts the equalization (EQ) for the
Cat 5e/6 cable lengths.

6
Installation
1. Connect an HDMI source (such as a Blu-ray player) to the transmitter.
2. Connect transmitter and receiver with a Cat5e/6 cable.
3. Connect an HDMI display to the receiver.
4. Connect the IR emitters and IR receivers.
5. Power on all the devices. Now you can adjust the panel EDID and EQ DIP switches
to obtain the desired viewing experience.

7
DIP Switch Description
EDID Management
EDID Overview
The transmitter features EDID management, which provides multiple EDID options for
outputting various resolutions, ensuring that the HDMI source reliably delivers correct
content to the display.
To change EDID settings, use a small flat bladed screwdriver to turn the panel rotary
switch towards the desired EDID number. The switch has click positions to make sure the
arrow is pointing at a number, not in-between. There is need to repower the unit when
adjusting EDID settings. The unit will then automatically apply the new settings
immediately.
Position
Functions
0 (default)
1080p, Stereo
1
1080p, 5.1
2
EDID Copy Mode (Copy EDID from Display)
3
1080i, Stereo
4
(Reserved)

8
Position
Functions
5
(Reserved)
6
(Reserved)
7
(Reserved)
Note:
If EDID Copy failed, a fixed 1080P@60Hz Stereo EDID would be provided to
source device.
Managing the EDID Information
By default, the EDID DIP switch is in the "0" position, outputting 1080p, stereo to display.
Through this switch, you can copy EDID information from the display or directly use the
fixed EDID information.
Copying EDID from the Display
1. Ensure that the display is powered on and connected to the receiver.
2. Ensure that transmitter and receiver are properly connected to each other that their
status LEDs are both solid on.
3. Locate the EDID DIP switch (outlined in the figure above) in the transmitter panel.
4. Move the switch to the "2" position.
5. Repower the transmitter for the changes to take effect. When an active source is
available, it will output the best video to the display based on the display's EDID
information.
Note:
If no display device has been connected to the receiver, the transmitter outputs the
factory default resolution (1080p, stereo) to the display.
Using the Fixed EDID
1. Ensure that the display is powered on and connected to the receiver.
2. Ensure that transmitter and receiver are properly connected to each other that their
status LEDs are both solid on.
3. Locate the EDID DIP switch (outlined in the figure above) in the transmitter panel.
4. Ensure that the display supports the desired EDID resolution. Otherwise, the display
may show no picture.
5. Toggle the switch to the position "0", "1" or "3" (see the table above for detailed EDID
information).
6. Repower the transmitter for the changes to take effect. When an active source is

9
available, it will output the fixed resolution to the display.
Note:
The fixed EDID function works properly even if no display is connected to the
receiver.
EQ Management
EQ Overview
The receiver features equalization (EQ) management, which provides multiple EQ options
for adjusting the EQ for the Cat 5e/6 cable lengths until you have the best picture quality.
To change EQ settings, use a small flat bladed screwdriver to turn the panel rotary switch
towards the desired EQ number. The switch has click positions to make sure the arrow is
pointing at a number, not in-between. There's no need to repower the unit when adjusting
EQ settings. The unit will then automatically apply the new setting immediately.
Situations
Positions
When the Cat 5e/6 cable is in the
range of 0 to 10 meters.
Set positions 0 through 3
When the Cat 5e/6 cable is in the
range of 10 to 30 meters.
Set positions 2 through 6
(4 by default)

10
Situations
Positions
When the Cat 5e/6 cable is in the
range of 30 to 40 meters.
Set positions 4 through 7
Reserved
Positions 8 through F
Adjusting the EQ Value
By default, the EQ DIP switch is in the "4" position, allowing you to use a Cat 5e/6 cable in
the range of 10 meters to 30 meters. Through this switch, you can adjust the desired EQ
value based on the actual cable length, obtaining a better viewing experience. If your
Cat 5e/6 cable is 20 meters long, follow the instructions below to adjust the EQ value.
1. Ensure that the display is powered on and connected to the receiver.
2. Ensure that transmitter and receiver are properly connected to each other, and that
their status LEDs are both solid on.
3. Locate the EQ DIP switch (outlined in the figure above) in the receiver panel.
4. Move the switch to cycle through positions 2 to 6.

11
Troubleshooting
W Box Technologies products are designed to function trouble-free.
Most problems that occur are due to simple issues. If you have
trouble, please check the list of simple fixes below.
EXTENDER TROUBLESHOOTING
PROBLEM
SOLUTION
STATUS LED OFF Ensure that the devices are powered on.
Check that the cables are qualified and
connected properly.
Check that the source input is active.
Check that the display works properly.
NO IMAGE Verify that all the devices are powered on, and that all the cables are qualified and
connected properly.
Verify that a picture is achieved when
connecting the source to the display
directly.
Check the EDID and EQ values. For more
information, see "DIP Switch Description".

12
Specification
Technical
Input / Output
Transmitter:
1 x RJ45 port
1 x HDMI IN
1 x IR IN
1 x IR OUT
Receiver:
1 x RJ45 Port
1 x HDMI OUT
1 x IR IN
1 x IR OUT
Input/Output Signal Type HDMI: HDMI 1.3a
Input/Output Resolution
Supported
1920 x 1080@60/50/30/25/24Hz,
1280 x 720@60/50/30/25/24Hz,
720 x 576@50Hz,
720 x 480@60Hz
Input Video Signal 1.2 V p-p
Input DDC Signal 5 V p-p (TTL)
Data Rate 2.25 Gbps (Max.)
Output Audio DTS-HD, Dolby-HD
IR Wavelength 940 nm
IR Frequency 38 KHz
Maximum Distance 130 feet (40 meters)

13
General
Power Supply 12 VDC 0.5 A (for each unit)
Power Consumption 5 W (Max.)
Operating Temperature +32°F to +113°F (0°C to +45°C)
10% to 90%, non-condensing
Storage Temperature -4°F to +158°F (-20°C to +70°C)
10% to 90%, non-condensing
ESD Protection Human Body Model: ±8kV (air-gap discharge)/
±4kV (contact discharge)
Dimensions 5'' × 2.12'' × 0.67''
(127mm × 54mm × 17mm)
Weight 0.66lb / 0.3kg (Pairs)
Certification CE, FCC, RoHS

14
Limited Warranty
1. Limited Warranty
a. General
Subject to the terms and conditions of this Limited Warranty, from
the date of sale through the period of time for product categories
specified in Section 1(b), ADI warrants its W Box Technologies
products to be free from defects in materials and workmanship
under normal use and service, normal wear and tear excepted.
Except as required by law, this Limited Warranty is only made to
Buyer and may not be transferred to any third party.
ADI shall have no obligation under this Limited Warranty or
otherwise if:
(i) The product is improperly installed, applied or maintained;
(ii) The product is installed outside of stated operating parameters,
altered, or improperly services or repaired;
(iii) Damage is caused by outside natural occurrences, such as
lightning, power surges, fire, floods, acts of nature, or the like.
(iv) Defects resulting from unauthorized modification, misuse,
vandalism, or other causes
(v) Unrelated to defective materials or workmanship, or failures
related to batteries of any type used in connection with the
products sold hereunder.
ADI only warrants those products branded as W Box Technologies
products and sold by ADI. Any other products branded by third
parties are warranted by the third party manufacturer for a period as
defined by the third party manufacturer, and ADI assigns to Buyer
those warranties and only those warranties extended by such third
party manufacturers or vendors for non-ADI branded products. ADI

15
does not itself warrant any non-ADI branded product and sells only
on an as is basis in accordance with ADI’s terms and conditions of
sale.
b. Specific Warranties for product categories are as follows:
Product Categories
Warranty Period
Soundbars
12 months
Walk Through Metal Detectors
12 months
Intrusion Wireless Communication
Accessories
12 months
Analog Cameras
24 months
HD TVI Cameras and HD TVI DVR’s
24 months
Televisions
24 months
CCTV Power Supplies
24 months
In Ceiling Speakers
24 months
Amplifiers
24 months
Magnetic Locks
24 months
Request to Exit Devices
24 months
Surge Protection
24 months
UPS (uninterruptible power supplies)
24 months
Volume Controls
24 months
HDMI Distribution
24 months
Intrusion Audio Devices
30 months
Monitors
30 months
Power and Relays
30 months
Hold-up Buttons
30 months
Video Baluns
30 months
DVR's, NVR's
60 months
IP Cameras
60 months
Racks
60 months
TV Mounts
60 months

16
Product Categories
Warranty Period
PIR’s
60 months
Analog Cables
Limited Lifetime
B Connectors
Limited Lifetime
Bus Terminals
Limited Lifetime
Extension Cords
Limited Lifetime
HDMI Cables
Limited Lifetime
Jacks, Cords and Intrusion
Communication Accessories
Limited Lifetime
Patch Cables
Limited Lifetime
Patch Panels
Limited Lifetime
Raceway Conduit
Limited Lifetime
Wire Ties
Limited Lifetime
Magnetic Contacts
Limited Lifetime

17
2. EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE
FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL
ADI BE LIABLE TO ANYONE FOR ANY (I) CONSEQUENTIAL,
INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES
ARISING OUT OF OR RELATING IN ANY WAY TO THE
PRODUCT AND.OR FOR BREACH OF THIS OR ANY OTHER
WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR UPON
ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE
LOSS OR DAMAGE IS CAUSED BY ADI’S OWN NEGLIGENCE
OR FAULT AND EVEN IF ADI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product
description (whether in writing or made orally by ADI or ADI’s
agents), specifications, samples, models, bulletin, drawings,
diagrams, engineering sheets, or similar materials used in
connection with the Buyer’s order are for the sole purpose of
identifying ADI’s products and shall not be construed as an express
warranty or condition. Any suggestions by ADI or ADI’s agents
regarding use, applications or suitability of the products shall not be
construed as an express warranty or condition unless confirmed to
be such in writing by ADI. ADI does not represent that the products
it sells may not be compromised or circumvented; that the products
will prevent any personal injury or property loss by burglary, robbery,
fire or otherwise, or that the products will in all cases provide
adequate warning or protection. Buyer understands and will cause
its customer to understand that a properly installed and maintained
product is not insurance or guarantee that such will not cause or
lead to personal injury or property loss. CONSEQUENTLY ADI
SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY,

18
PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM
AT ALL INCLUDING A CLAIM THAT THE PRODUCT FAILED TO
GIVE WARNING. However, if ADI is held liable whether directly or
indirectly for any loss or damage with respect to the products it sells,
regardless of cause or origin, its maximum liability shall not in any
case exceed the purchase price of the product, which shall be fixed
as liquidated damages and not as a penalty and shall be the
complete and exclusive remedy against ADI.
3. Limitation on Liability to Buyer’s Customers.
Buyer agrees to limit liability to its customers to the fullest extent
permitted by law. Buyer acknowledges that ADI shall only be
deemed to give consumers of its products such statutory warranties
as may be required by law and at no time shall Buyer represent to
its customers and/or users of ADI products that ADI provides any
additional warranties. By accepting the products, to the fullest
extent permitted by law, Buyer assumes all liability for, and agrees
to indemnity and hold ADI harmless against and defend ADI from,
any and all suits, claims, demands, causes of action and judgments
relating to damages, whether for personal injury or to personal
property, suffered by any person, firm, corporation or business
association, including but not limited to, Buyer’s customers and/or
users of the products because of any failure of the products to
detect and/or warn of the danger for which the goods were
designed or any other failure of the products whether or not such
damages are caused or contributed to by the sold or joint concurring
negligence or fault of ADI.
4. Returns
Subject to the terms and conditions listed below, during the
applicable warranty period, ADI will replace Product or provide a

19
credit at purchase at its sole option free of charge any defective
products returned prepaid. Any obligations of ADI to replace Limited
Lifetime warranty products pursuant to this warranty which result
from defect are limited to the availability of replacement product.
ADI reserves the right to replace any such products with the then
currently available products, or provide a credit in its sole discretion.
In the event Buyer has a problem with any ADI product, please call
your local ADI branch for return instructions:
For US call 1-800-233-6261
For Canada call 877-234-7378
For Puerto Rico call 787-793-8830
Be sure to have the model number and the nature of the problem
available. In the event of replacement, the return product will be
credited to Buyer’s account and a new invoice issued for the
replacement item. ADI reserves the right to issue a credit only in lieu
of replacement.
If any W Box Technologies product is found to be in good working
order or such product’s inability to function properly is a result of
user damage or abuse, the product will be returned to Buyer in the
same condition as received and Buyer shall be responsible for any
return freight changes.
5. Governing Law
The laws of State of New York apply to this Limited Warranty.

20
6. Miscellaneous
Where any term of this Limited Warranty is prohibited by such laws,
it shall be null and void, but the remainder of the Limited Warranty
shall remain in full force and effect.