W Box Technologies 0E-HDMIEXT4K Reference manual

Introduction
Congratulations and thank you for purchasing W Box Technologies
0E-HDMIEXT4K.
0E-HDMIEXT4K is a slim transmitter receiver pair which is
designed to extend HDMI 1080P@60Hz signals up to 70 m and
4K@60Hz (4:2:0) signals up to 40m via a single Cat 6a/7 cable.
The transmitter can supply the power for the receiver. You can
control the source from the display's location or control the display
from source's location via IR pass-through function. The transmitter
and receiver are easy to install. They are space saving and offer
solutions for home, office, digital entertainment centers, control
centers, conference rooms, school and corporate training
environments.
Please follow the instructions in this manual to assure proper
installation and to achieve the full performance and satisfaction you
would expect from W Box Technologies.
!1

Features
•Slim appearance and space saving
•Bi-directional PoE, only one power adapter is needed.
•Via Cat 6a/7 cables, 4Kx2K@60Hz (4:2:0) output up to 130
feet (40m), 1080P@60Hz up to 230feet (70m).
•Via Cat 5e/6 cable, 4Kx2K@60Hz (4:2:0) output up to 115 feet
(35m), 1080P@60Hz up to 198feet (60m).
•HDMI 1.4 with 4K and HDCP 2.2 compliant.
•Transfers bi-directional infrared control signal together with the
HDMI signal.
•Use the transmitter and receiver pair to extend HDMI signals
without additional settings.
•All connectors in one side for easy cabling.
!2

Package Contents
Before you start the installation, please check the package
contents:
•1 x 0E-HDMIEXT4K
•1 x Power Adapter (DC 18V 1A)
•2 x IR Emitter
•2 x IR Receiver (30-50KHz)
•4 x Mounting Brackets
•1 x User Manual
•1 x Datasheet
!3

Panel
Transmitter
Front Panel

ID.
Name
Description
1
POWER LED
Steady red: Transmitter is powered on.
2
LINK LED
Steady green: Link to receiver has
been established.
Blinking/Off: Connection exceptions
exist between the transmitter and the
receiver.
!4

Rear Panel

ID.
Name
Description
1
Power
Connects to DC 18V 1A power adapter.
Note: Only one power adapter is needed
at transmitter or receiver side.
2
HDBT OUT
Connects to the receiver via Cat5e/6/6a/7
cable.
3
IR IN
Connects to an IR receiver cable. Secure
the IR receiver with adhesive.
Note: The IR receiver enabled angle and
distance:
Enabled Angel0° 30°
(Horizontal) 15°
(Vertical)
Distance 8m(Max) 4.5m(Max) 3m(Max)
4
IR OUT
Connects to an IR emitter cable. Secure
the IR emitter on the IR receiving sensor of
display device with adhesive.
5
HDMI IN
Connects to a HDMI source device.
!5

Receiver
Front Panel
!
ID.
Name
Description
1
POWER
LED
Steady red: Receiver is powered on.
2
LINK LED
Steady green: Link to transmitter has
been established.
Blinking/Off: Connection exceptions exist
between the transmitter and the receiver.
!6

Rear Panel
!
ID.
Name
Description
1
Power
Connects to DC 18V 1A power adapter.
Note: Only one power adapter is needed
at transmitter or receiver side.
2
HDBT IN
Connects to the transmitter via Cat5e/
6/6a/7 cable.
3
IR IN
Connects to an IR receiver cable. Secure
the IR receiver with adhesive.
Note: The IR receiver enabled angle and
distance:
Enabled Angel0° 30°
(Horizontal) 15°
(Vertical)
Distance 8m(Max) 4.5m(Max) 3m(Max)
4
IR OUT
Connects to an IR emitter cable. Secure
the IR emitter on the IR receiving sensor
of display device with adhesive.
5
HDMI OUT
Connects to a HDMI display device.
!7

Installation
The product packaging includes two pairs of IR cables, please refer
to the following two applied installations with different remote
handsets.
Applied installation 1
Control the DVD at TV side by DVD remote:
!8

1. Connect an HDMI source (such as a DVD) to the transmitter.
As show number 1 in figure.
2. Connect transmitter and receiver with a Cat5e/6/6a/7 cable.
Note: make sure CatX cable is less than 230ft for 1080p. 130ft
for 4K resolution. As show number 2 in figure.
3. Connect an HDMI display (such as a TV) to the receiver. As
show number 3 in figure.
4. Connect the IR receiver cable to IR IN port of the receiver. As
show number 4 in figure.
5. Connect the IR emitter cable to the IR OUT port of the
transmitter, the IR emitter head should be secured over the
center of the DVD IR window. As show number 5,6 in figure.
6. Connect the power adapter to DC 18V port. As show number 7
in figure.
7. Power on all the devices. Now you can enjoy the audio and
video experience.
!9

Applied installation 2
Control the TV at DVD side by TV remote:
!10

1. Connect an HDMI source (such as a DVD) to the transmitter.
As show number 1 in figure.
2. Connect transmitter and receiver with a Cat5e/6/6a/7 cable.
Note: make sure CatX cable is less than 230ft for 1080p. 130ft
for 4K resolution. As show number 2 in figure.
3. Connect an HDMI display (such as a TV) to the receiver. As
show number 3 in figure.
4. Connect the IR receiver cable to IR IN port of the transmitter.
As show number 4 in figure.
5. Connect the IR emitter cable to the IR OUT port of the receiver,
the IR emitter head should be secured over the center of the
TV IR window. As show number 5, 6 in figure.
6. Connect the power adapter to DC 18V port. As show number 7
in figure.
7. Power on all the devices. Now you can enjoy the audio and
video experience.
!11

Troubleshooting
W Box Technologies products are designed to function trouble-free.
Most problems that occur are due to simple issues. If you have
trouble, please check the list of simple fixes below.
Six Steps of Regular Troubleshooting Routine.
1. Power: Make sure all devices are powered on. (source,
extender, display device)
2. Indicator: Make sure LED indicators of extender are normal
according to user manual.
3. Devices: Please make sure picture can be shown normally
when connecting source to display devices directly.
4. Cable: Plug in and out HDMI/CatX cable or try another HDMI/
CatX cable.
•Cat 5e/6/6a/7 cable is recommended, do not use Cat 5
cable.
•Please make sure CatX cable is less than 230ft for 1080p,
130ft for 4K resolution.
•Please make sure the two connectors of one CatX cable
are same standard (EIA/TIA 568B).
5. Compatibility:
•Please test the source and display devices to determine
whether there is compatibility issues.
•HDMI extender supports 3G speed (4K@60Hz 4:2:0 8bit)
maximum, when both HDMI source and display devices
support 6G speed (4K@60Hz 4:4:4 8bit), display device
will not output signal. (Even though all the LEDs of
extender are normal.) Please set HDMI source resolution
to 4K@60Hz 4:2:0 8bit or ask help from Source Device
Supplier.
•For Vizio TV, when every device is well connected and all
the LEDs are normal. but Vizio TV can not display well,
please ask help from Vizio TV and update the TV setting.
Typical questions
!12

1. How to deal with video flash or cut off during the
installation?
•Power indicator should be solid on. If not, please check if
the power adapter is well connected.
•Link indicator should be solid on, if it is blinking or off, it is
likely a problem with your Ethernet cable, please change to
a qualified cable (Cat5e/6/6a/7, EIA/TIA 568B) and make
sure the cable length is within the maximum distance (230ft
for 1080p, 130ft for 4K).
2. How to deal with a weak or not working IR signal?
•Make sure the IR cables are correctly installed according to
the diagram above.
•Check if the IR emitter head is secured over the center of
the device IR receiver window. The best position may vary
depending on the device, please refer to the device user
manual. If the signal is weak, please try adjusting the
position.
•Pay attention to the control angle and distance as below:
The control signal will be better when your controller is
pointed at the IR receiver head directly.
3. How can I make the IR work with third party control
devices?
Please make sure the third party device follows our pin
definition as below:
Enabled Angle
0°
30°(Horizontal)
15°(Vertical)
Distance
8m(Max)
4.5m(Max)
3m(Max)
!13

Specification
!14

Technical
Input/Output Signal Type
HDMI 1.4 with HDCP 2.2
Audio Format
Stereo, PCM 2.1/5.1/7.1, DTS,
Dolby, pass through
Input/Output Resolution
Supported
SMPTE: !
1280x720P1,2,3,4,5,6,7,8,
1920x1080I6,8,
1920x1080P1,2,3,4,5,6,7,8,!
3840x21602,3,5, 4096x21602,3,5;!
!
VESA: !
800x6008, 1024x7688, 1280x7688,
1280x8008, 1280x9608,
1280x10248, 1360x7688,
1366x7688, 1400x10508,
1440x9008, 1600x9008,
1600x12008, 1680x10508,
1920x12008, !
!
1 = at 23.98 Hz, 2 = at 24 Hz, 3 =
at 25 Hz, 4 = at 29.97 Hz, 5 = at 30
Hz, 6 = at 50 Hz, 7 = at 59.94 Hz, 8
= at 60 Hz;
Maximum Data Rate
10.2 Gpbs
Maximum Pixel Clock
340 MHz
General
Operating Temperature
+32°F to +113°F (0°C to +45°C)
10% to 90%, non-condensing
Storage Temperature
-4°F to +158°F (-20°C to +70°C)
10% to 90%, non-condensing
!15

Cable Specifications:
Note: We recommend the use of T568B straight-through Category
cables.
ESD Protection
Human Body Model:
±8kV (air-gap discharge)/
±4kV (contact discharge)
Power Consumption
8.8 W Max (Pair)
Dimensions
4.55'' ×2.55'' ×0.83''
(115mm ×64.5mm ×21mm)
Weight
Transmitter: 0.48lb/0.22kg
Receiver: 0.48lb/0.22kg
Certification
CE, FCC, RoHS
Cable Type
Range
Supported Video
CAT5e/CAT6
60m
1080p, 60Hz 36 bpp
35 m
1080p 60 Hz 48 bpp
1080p 60 Hz 3D
3840 x 2160@60Hz
4:2:0 8bit
CAT6a/CAT7
70 m
1080p, 60 Hz 36 bpp
40 m
1080p 60 Hz 48 bpp
1080p 60 Hz 3D
3840 x 2160@60Hz
4:2:0 8bit
!16

Limited Warranty
1. Limited Warranty
a. General
Subject to the terms and conditions of this Limited Warranty, from
the date of sale through the period of time for product categories
specified in Section 1(b), ADI warrants its W Box Technologies
products to be free from defects in materials and workmanship
under normal use and service, normal wear and tear excepted.
Except as required by law, this Limited Warranty is only made to
Buyer and may not be transferred to any third party.
ADI shall have no obligation under this Limited Warranty or
otherwise if:
(i) The product is improperly installed, applied or maintained;
(ii) The product is installed outside of stated operating parameters,
altered, or improperly services or repaired;
(iii) Damage is caused by outside natural occurrences, such as
lightning, power surges, fire, floods, acts of nature, or the like.
(iv) Defects resulting from unauthorized modification, misuse,
vandalism, or other causes
(v) Unrelated to defective materials or workmanship, or failures
related to batteries of any type used in connection with the
products sold hereunder.
ADI only warrants those products branded as W Box Technologies
products and sold by ADI. Any other products branded by third
parties are warranted by the third party manufacturer for a period
as defined by the third party manufacturer, and ADI assigns to
Buyer those warranties and only those warranties extended by
such third party manufacturers or vendors for non-ADI branded
products. ADI does not itself warrant any non-ADI branded product
and sells only on an as is basis in accordance with ADI’s terms and
conditions of sale.
b. Specific Warranties for product categories are as follows:
!17

Product Categories
Warranty Period
Soundbars
12 months
Walk Through Metal Detectors
12 months
Intrusion Wireless Communication
Accessories
12 months
Analog Cameras
24 months
HD TVI Cameras and HD TVI DVR’s
24 months
Televisions
24 months
CCTV Power Supplies
24 months
In Ceiling Speakers
24 months
Amplifiers
24 months
Magnetic Locks
24 months
Request to Exit Devices
24 months
Surge Protection
24 months
UPS (uninterruptible power supplies)
24 months
Volume Controls
24 months
HDMI Distribution
24 months
Intrusion Audio Devices
30 months
Monitors
30 months
Power and Relays
30 months
Hold-up Buttons
30 months
Video Baluns
30 months
DVR's, NVR's
60 months
!18

IP Cameras
60 months
Racks
60 months
TV Mounts
60 months
PIR’s
60 months
Analog Cables
Limited Lifetime
B Connectors
Limited Lifetime
Bus Terminals
Limited Lifetime
Extension Cords
Limited Lifetime
HDMI Cables
Limited Lifetime
J a c k s , C o r d s a n d I n t r u s i o n
Communication Accessories
Limited Lifetime
Patch Cables
Limited Lifetime
Patch Panels
Limited Lifetime
Raceway Conduit
Limited Lifetime
Wire Ties
Limited Lifetime
Magnetic Contacts
Limited Lifetime
Product Categories
Warranty Period
!19

2. EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY
THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A
PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND
BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE
FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL
ADI BE LIABLE TO ANYONE FOR ANY (I) CONSEQUENTIAL,
INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES
ARISING OUT OF OR RELATING IN ANY WAY TO THE
PRODUCT AND.OR FOR BREACH OF THIS OR ANY OTHER
WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR
UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN
IF THE LOSS OR DAMAGE IS CAUSED BY ADI’S OWN
NEGLIGENCE OR FAULT AND EVEN IF ADI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR
DAMAGES. Any product description (whether in writing or made
orally by ADI or ADI’s agents), specifications, samples, models,
bulletin, drawings, diagrams, engineering sheets, or similar
materials used in connection with the Buyer’s order are for the sole
purpose of identifying ADI’s products and shall not be construed as
an express warranty or condition. Any suggestions by ADI or ADI’s
agents regarding use, applications or suitability of the products
shall not be construed as an express warranty or condition unless
confirmed to be such in writing by ADI. ADI does not represent that
the products it sells may not be compromised or circumvented; that
the products will prevent any personal injury or property loss by
burglary, robbery, fire or otherwise, or that the products will in all
cases provide adequate warning or protection. Buyer understands
and will cause its customer to understand that a properly installed
and maintained product is not insurance or guarantee that such will
not cause or lead to personal injury or property loss.
CONSEQUENTLY ADI SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS
BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THAT THE
PRODUCT FAILED TO GIVE WARNING. However, if ADI is held
liable whether directly or indirectly for any loss or damage with
!20