WAC Lighting Line LN-LED06 User manual

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2014
INSTALLATION INSTRUCTION
Line™ LED Edge Lit Task Luminaire
LN-LED
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
• Read all instructions before installing.
• Always turn o the power at fuse box prior to installation to prevent electrical shock.
• To be installed by a qualied electrician.
• System is intended for installation in accordance with National Electric Code and local regulations.
• Consult with local inspector to assure compliance.
• Keep away from combustible materials such as plastic or paper products.
• Do not operate with missing or damaged parts.
PRODUCT INCLUDES
• Docking station
• LED light panel
• “I” Connector
• Mounting screws
INSTALLATION
1. Choose the proper mounting position for the xture, recommended either at the back or front of the cabinet.
2. Fasten the docking station to surface using the provided mounting screws.
3. Snap the LED light panel onto the docking station by aligning the circular handles on the panel to the magnets in
the circular holes on the docking station.

WAC Lighting
www.waclighting.com
Phone [phone] • Fax [phone]
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2014
INSTALLATION INSTRUCTION
Line™ LED Edge Lit Task Luminaire
LN-LED
WIRING
Insert plug end of cord from transformer into either end of the docking station.
TRANSFORMERS NEEDED SOLD SEPARATELY:
60W plug in (120V) EN-2460-P-AR-S
96W plug in (120V) EN-24100-P-AR-S
60W remote (120V) EN-2460-RB2-S
96W remote (120V) EN-24100-RB2-S
96W remote (277V) EN-24100-277-R (Requires a SL-EXT-144 extension cable. order separately)
CONNECTING MULTIPLE FIXTURES END TO END CONNECTION ICONNECTOR INCLUDED:
1. The “I” connector allows two xtures to connect end to end.
2. Insert one end of the “I” connector into the docking station.
3. Slide the next docking station into place.
INTERCONNECTING FIXTURES WITH JUMPER WIRES SOLD SEPARATELY:
A surface mount jumper wire allows multiple units to be linked through surface wiring.
Insert the end of the connectors into each xture.
If your jumper wire needs to be extended use our“IF”cable (SL-IF) to connect them together to lengthen.
AVAILABLE LENGTHS AND CONFIGURATIONS SOLD SEPARATELY
SL-IC-06 6 inch
SL-IC-12 12 inch
SL-IC-24 24 inch
SL-IC-36 36 inch
SL-Y Y connector
SL-X X connector
SL-IF IF cable connector
WIRING BOX WITH SWITCH SOLD SEPARATELY
For low voltage wiring use only 12V/24V 4A
12AWG to 20AWG
Model: TB-S
TERMINAL BLOCK SOLD SEPARATELY
Use terminal block to connect up to 8 xtures
Model: MTB-08 8 output
Please follow guidelines below for the number of units that can be wired in series
EN-2460-P-AR-S
(60W)
EN-24100-P-AR-S
(100W)
EN-2460-RB2-S
(60W)
EN-24100-RB2-S
(100W)
LN-LED06 8 14 8 14
LN-LED12 5858
LN-LED18 3535
LN-LED24 2424
LN-LED30 2323