WAGO I/O-SYSTEM 750 User manual

Manual
WAGO-I/O-SYSTEM 750
750-471
4AI U/I Diff Galv
4
-Channel Analog Input; for Voltage/Current
Version 1.0.0
All manuals and user guides at all-guides.com

2 WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
© 2018 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [e-mail]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [e-mail]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [e-mail]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Table of Contents 3
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
Table of Contents
1Notes about this Documentation .............................................................5
1.1 Validity of this Documentation.................................................................5
1.2 Copyrights ..............................................................................................5
1.3 Copyright................................................................................................7
1.4 Symbols .................................................................................................8
1.5 Number Notation ..................................................................................10
1.6 Font Conventions .................................................................................10
2Important Notes ......................................................................................11
2.1 Legal Bases..........................................................................................11
2.1.1 Subject to Changes..........................................................................11
2.1.2 Personnel Qualifications ..................................................................11
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying
Provisions ........................................................................................11
2.1.4 Technical Condition of Specified Devices.........................................12
2.1.4.1 Disposal ......................................................................................12
2.2 Safety Advice (Precautions) .................................................................13
3Device Description..................................................................................15
3.1 View .....................................................................................................18
3.2 Connectors...........................................................................................19
3.2.1 Data Contacts/Local Bus..................................................................19
3.2.2 Power Jumper Contacts/Field Supply ..............................................20
3.2.3 CAGE CLAMP®Connectors.............................................................22
3.3 Display Elements..................................................................................23
3.4 Schematic Diagram ..............................................................................25
3.5 Technical Data .....................................................................................26
3.5.1 Device Data .....................................................................................26
3.5.2 Supply..............................................................................................26
3.5.3 Isolation ...........................................................................................26
3.5.4 Communication................................................................................26
3.5.5 Inputs...............................................................................................27
3.5.6 Connection Type..............................................................................27
3.5.7 Climatic Environmental Conditions...................................................28
3.6 Approvals .............................................................................................29
3.7 Standards and Guidelines ....................................................................30
4Process Image.........................................................................................31
4.1 Overview ..............................................................................................31
4.2 Status bytes..........................................................................................33
4.3 Process Data........................................................................................34
4.3.1 Overview of Sensor Types ...............................................................34
4.3.1.1 Signal Types “0 … 10 V”, “0 … 20 mA” and “4 … 20 mA” (Default)35
4.3.1.2 Signal Types “± 10 V”, “± 200 mV” “± 20 mA”, Two’s complement
(Default) ......................................................................................37
4.3.1.3 Signal Type “Namur NE43”..........................................................40
5Mounting..................................................................................................44
All manuals and user guides at all-guides.com

4 Table of Contents WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
5.1 Mounting Sequence..............................................................................44
5.2 Inserting and Removing Devices ..........................................................45
5.2.1 Inserting the I/O Module...................................................................45
5.2.2 Removing the I/O Module ................................................................46
6Connect Devices .....................................................................................47
6.1 Connecting a Conductor to the CAGE CLAMP®...................................47
6.2 Connection Examples...........................................................................48
7Commissioning .......................................................................................49
7.1 Parameterization with WAGO-I/O-CHECK............................................49
7.1.1 Parameterization Dialog...................................................................51
7.1.2 Toolbar on the Configuration Dialog.................................................52
7.1.3 Navigation area................................................................................53
7.1.3.1 Common......................................................................................54
7.1.3.2 Channel Settings .........................................................................56
7.1.3.3 Scaling ........................................................................................58
7.1.3.4 Calibration ...................................................................................60
7.2 Scaling Measured Values .....................................................................64
8Diagnostics..............................................................................................65
8.1 I/O Module Behavior in the Event of an Error........................................65
8.2 Firmware Changes ...............................................................................68
9Use in Hazardous Environments ...........................................................69
9.1 Marking Configuration Examples ..........................................................70
9.1.1 Marking for Europe According to ATEX and IECEx..........................70
9.1.2 Marking for America (NEC) and Canada (CEC) ...............................73
9.2 Installation Regulations.........................................................................77
9.2.1 Special Notes Regarding Explosion Protection ................................77
9.2.2 Special Notes Regarding ANSI/ISA Ex ............................................79
10 Appendix .................................................................................................80
10.1 Configuration and Parameterization using a GSD File with PROFIBUS
DP and PROFINET IO..........................................................................80
10.1.1 4AI U/I Diff/Galv Configuration .........................................................80
10.1.1.1 PROFIBUS DP Fieldbus Couplers/Controllers 750-333(/0xx-000),
750-833(/0xx-000) .......................................................................80
10.1.1.2 PROFINET IO Fieldbus Couplers 750-375(/025-000), 750-
377(/025-000)..............................................................................80
10.1.2 4AI U/I Diff/Galv Parameterization....................................................81
10.1.2.1 All PROFIBUS DP and PROFINET IO Fieldbus
Couplers/Controllers....................................................................83
10.1.2.2 PROFIBUS DP Fieldbus Couplers/Controllers 750-333(/0xx-000),
750-833(/0xx-000) .......................................................................84
10.1.2.3 PROFINET IO Fieldbus Couplers 750-375(/025-000), 750-
377(/025-000)..............................................................................84
List of Figures ..................................................................................................87
List of Tables....................................................................................................88
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
1 Notes about this Documentation
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
1.1 Validity of this Documentation
This documentation is only applicable to the I/O module 750-471
(4AI U/I Diff Galv).
The I/O module 750-471 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
1.2 Copyrights
Copyright (c) 2009 - 2015 ARM LIMITED. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
- Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
- Neither the name of ARM nor the names of its contributors may be used to
endorse or promote products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND
All manuals and user guides at all-guides.com

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright © 2015 STMicroelectronics International N.V.. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted, provided that the following conditions are met:
1. Redistribution of source code must retain the above copyright notice, this
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. Neither the name of STMicroelectronics nor the names of other contributors
to this software may be used to endorse or promote products derived from
this software without specific written permission.
4. This software, including modifications and/or derivative works of this
software, must execute solely and exclusively on microcontroller or
microprocessor devices manufactured by or for STMicroelectronics.
5. Redistribution and use of this software other than as permitted under this
license is void and will automatically terminate your rights under this
license.
THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT
PERMITTED BY LAW. IN NO EVENT SHALL STMICROELECTRONICS OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
1.3 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
All manuals and user guides at all-guides.com

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
1.4 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Notes about this Documentation 9
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
All manuals and user guides at all-guides.com

10 Notes about this Documentation WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
1.5 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
1.6 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under
Start of measurement range
.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Important Notes 11
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
2 Important Notes
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
2.1 Legal Bases
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in
the section “Device Description” > “Standards and Guidelines” in the manual for
the used fieldbus coupler/controller.
Appropriate housing (per 2014/34/EU) is required when operating the
WAGO-I/O-SYSTEM 750 in hazardous environments. Please note that a
All manuals and user guides at all-guides.com

12 Important Notes WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
prototype test certificate must be obtained that confirms the correct installation of
the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F-I/O modules within the modular
WAGO-I/O-SYSTEM 750. Only these safe F-I/O modules ensure functional
safety in accordance with the latest international standards. WAGO's
interference-free output modules can be controlled by the safety function.
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
•Repairs,
•Changes to the hardware or software that are not described in the
operating instructions,
•Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
2.1.4.1 Disposal
Recycle metals, plastics and packaging materials.
Automation components used in the professional sector (B2B) must be properly
disposed of once no longer in use in accordance with the respective national
guidelines (e.g., European Community Directive WEEE 2012/19/EU).
Packaging of all types must be disposed of in such a way that a high level of
recovery, reuse and recycling is possible. PPWD 94/62/EU and 2004/12/EU
packaging guidelines apply throughout Europe.
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Important Notes 13
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
2.2 Safety Advice (Precautions)
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this I/O module (750-471) must
be powered from SELV/PELV power supply(s)!
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
All manuals and user guides at all-guides.com

14 Important Notes WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Device Description 15
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
3 Device Description
The 750-471 I/O Module 750-471 (4AI U/I Diff Galv) processes differential current
and voltage signals from the field:
•0 … 10 V
•± 10 V
•± 200 mV
•0 … 20 mA
•3,6 … 21 mA NE43
•4 … 20 mA
•± 20 mA
The I/O module has four electrically isolated input channels for differential
signals. The sensors are connected to the CAGE CLAMP® terminals +AI1 and
−AI1, +AI2 and −AI2, +AI3 and −AI3, +AI4 and −AI4.
The assignment of the connections is described in the “Connectors” section.
Connection examples are shown in section “Connect Devices” > … >
“Connection Example(s)”.
The input signal is electrically isolated and transmitted with a resolution of 16 bits.
The operational readiness and the trouble-free local bus communication of the
channels are indicated via a green function LED.
A red fault LED per channel indicates that the signal is outside the measuring
range and depending on the type of signal additionally an overload or a wire
break.
Details about the individual signal types are described in the “Process Image” >
“Process Data” section.
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node.
An arrangement in groups within the group of potentials is not necessary.
Power to the internal electronics is supplied via internal data bus.
The 750-471 module can be used with the fieldbus couplers and controllers of
the WAGO-I/O-SYSTEM 750 of the specified version or higher listed in the
“Compatibility list” table.
All manuals and user guides at all-guides.com

16 Device Description WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
Table 3: Compatibility List 750-471
Bus System
Fieldbus Couplers/
Controllers
Item No.
Revision Status
Firmware
PROFINET Fieldbus coupler
750-375
01
750-377
01
PROFIBUS
Fieldbus coupler
750-333
20
Controller
750-833
19
ETHERNET
Fieldbus coupler
750-341
09
750-342
18
750-352
10
Controller
750-841
21
750-842
19
750-843
03
750-852
10
750-871
09
750-872
05
750-873
05
750-880
10
750-881
10
750-882
10
750-885
10
Application controller BA
750-884
10
Controller PFC100
750-810x
10
Controller PFC200
750-82xx
10
DeviceNet
Fieldbus coupler
750-306
4L
ECO fieldbus coupler
750-346
11
Controller
750-806
11
CANopen
Fieldbus coupler
750-337
21
750-338
21
ECO-Fieldbus coupler
750-347
12
750-348
12
Controller
750-837
17
750-838
17
MODBUS
Fieldbus coupler
750-315/300-000
01
750-316/300-000
01
Controller
750-815/300-000
01
750-816/300-000
01
EtherCat
Fieldbus coupler
750-354
03
CC-Link
Fieldbus coupler
750-325
01
BACnet
Fieldbus coupler
750-330
09
Controller
750-829
09
750-830
09
750-831
09
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Device Description 17
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
Table 3: Compatibility List 750-471
Bus System
Fieldbus Couplers/
Controllers
Item No.
Revision Status
Firmware
KNX Controller
750-849
09
750-889
10
Various I/O IPC
758-870/000-11x
09
758-874/000-11x
09
758-875/000-11x
09
758-876/000-11x
09
Other fieldbus couplers/controllers on request!
All manuals and user guides at all-guides.com

18 Device Description WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
3.1 View
Figure 1: View
Table 4: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
CAGE CLAMP®connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
All manuals and user guides at all-guides.com

WAGO-I/O-SYSTEM 750 Device Description 19
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
3.2 Connectors
3.2.1 Data Contacts/Local Bus
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. It is
comprised of 6 data contacts, which are available as self-cleaning gold spring
contacts.
Figure 2: Data Contacts
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
All manuals and user guides at all-guides.com

20 Device Description WAGO-I/O-SYSTEM 750
750-471 4AI U/I Diff Galv
Manual
Version 1.0.0
3.2.2 Power Jumper Contacts/Field Supply
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
The I/O module 750-471 has 2 self-cleaning power jumper contacts that supply
and transmit power for the field side. The contacts on the left side of the I/O
module are designed as blade contacts and those on the right side as spring
contacts.
Figure 3: Power Jumper Contacts
Table 5: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded.
If exceeded, insert an additional supply module.
All manuals and user guides at all-guides.com