WAGO WAGO-I/O-SYSTEM 750 XTR Series User manual

Manual
WAGO I/O System 750 XTR
750-471/040-000
4AI U/I Diff Galv XTR
4
-Channel Analog Input; for Voltage/Current;
Extreme
Version 1.0.2

2 WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
© 2022 WAGO GmbH & Co. KG
All rights reserved.
WAGO GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

WAGO I/O System 750 XTR Table of Contents 3
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
Table of Contents
1Notes about this Documentation .............................................................5
1.1 Validity of this Documentation.................................................................5
1.2 Copyrights ..............................................................................................5
1.3 Copyright................................................................................................7
1.4 Symbols .................................................................................................8
1.5 Number Notation ..................................................................................10
1.6 Font Conventions .................................................................................10
2Important Notes ......................................................................................11
2.1 Legal Bases..........................................................................................11
2.1.1 Subject to Changes..........................................................................11
2.1.2 Personnel Qualifications ..................................................................11
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions.....11
2.1.4 Technical Condition of Specified Devices.........................................12
2.1.4.1 Disposal ......................................................................................12
2.1.4.1.1 Electrical and Electronic Equipment........................................12
2.1.4.1.2 Packaging...............................................................................13
2.2 Safety Advice (Precautions) .................................................................14
3Device Description..................................................................................18
3.1 View .....................................................................................................21
3.2 Connectors...........................................................................................22
3.2.1 Data Contacts/Local Bus..................................................................22
3.2.2 Power Jumper Contacts/Field Supply ..............................................23
3.2.3 CAGE CLAMP®Connectors.............................................................24
3.3 Display Elements..................................................................................25
3.4 Schematic Diagram ..............................................................................27
3.5 Technical Data .....................................................................................28
3.5.1 Device Data .....................................................................................28
3.5.2 Supply..............................................................................................28
3.5.3 Isolation ...........................................................................................28
3.5.4 Inputs...............................................................................................29
3.5.5 Communication................................................................................29
3.5.6 Connection Type..............................................................................29
3.5.7 Mechanical Conditions .....................................................................30
3.5.8 Climatic Environmental Conditions...................................................30
3.6 Approvals .............................................................................................31
3.7 Standards and Guidelines ....................................................................33
4Process Image.........................................................................................40
4.1 Overview ..............................................................................................40
4.2 Status bytes..........................................................................................42
4.3 Process Data........................................................................................43
4.3.1 Overview of Sensor Types ...............................................................43
4.3.1.1 Signal Types “0 … 10 V”, “0 … 20 mA” and “4 … 20 mA”
(Default) ......................................................................................44
4.3.1.2 Signal Types “±10 V”, “±200 mV” “±20 mA”, Two’s complement
(Default) ......................................................................................46

4 Table of Contents WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
4.3.1.3 Signal Type “Namur NE43”..........................................................49
5Mounting..................................................................................................53
5.1 Mounting Sequence..............................................................................53
5.2 Inserting and Removing Devices ..........................................................54
5.2.1 Inserting the I/O Module...................................................................54
5.2.2 Removing the I/O Module ................................................................55
6Connect Devices .....................................................................................56
6.1 Connecting a Conductor to the CAGE CLAMP®...................................56
6.2 Connection Examples...........................................................................57
7Commissioning .......................................................................................58
7.1 Configuration and Parameterization with WAGO Software Tools.........58
7.1.1 Start via WAGO-I/O-CHECK ............................................................58
7.1.2 Parameterization Dialog...................................................................61
7.1.3 Toolbar on the Configuration Dialog.................................................61
7.1.4 Navigation area................................................................................62
7.1.4.1 Common......................................................................................63
7.1.4.2 Channel Settings .........................................................................65
7.1.4.3 Scaling ........................................................................................66
7.1.4.4 Calibration ...................................................................................68
7.2 Configuration and Parameterization via GSD File.................................71
7.2.1 4AI U/I Diff/Galv Configuration .........................................................71
7.2.1.1 PROFIBUS DP Fieldbus Couplers 750-333/040-000...................71
7.2.2 4AI U/I Diff/Galv Parameterization....................................................72
7.2.2.1 All PROFIBUS DP and PROFINET IO Fieldbus
Couplers/Controllers....................................................................73
7.2.2.2 PROFIBUS DP Fieldbus Couplers 750-333/040-000...................74
7.3 Scaling Measured Values .....................................................................75
8Diagnostics..............................................................................................76
8.1 I/O Module Behavior in the Event of an Error........................................76
8.2 Firmware Update..................................................................................79
9Use in Hazardous Environments ...........................................................80
9.1 Marking Configuration Examples ..........................................................81
9.1.1 Marking for Europe According to ATEX and IECEx..........................81
9.1.2 Marking for the United States of America (NEC) and Canada
(CEC)...............................................................................................85
9.2 Installation Regulations.........................................................................88
9.2.1 Special Notes including Explosion Protection...................................88
9.2.2 Special Notes Regarding UL Hazardous Location............................90
List of Figures ..................................................................................................91
List of Tables....................................................................................................92

WAGO I/O System 750 XTR Notes about this Documentation 5
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
1 Notes about this Documentation
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
1.1 Validity of this Documentation
This documentation is only applicable to the I/O module 750-471/040-000
(4AI U/I Diff Galv XTR).
The I/O module 750-471/040-000 shall only be installed and operated according
to the instructions in this manual, in the system description for the WAGO I/O
System 750 XTR and in the manual for the used fieldbus coupler/controller.
Consider power layout of the WAGO I/O System 750 XTR!
In addition to these operating instructions, you will also need the system
description “Design Notes XTR – Guidelines and Recommendations for
Increasing Operational Safety” and the manual for the used fieldbus
coupler/controller, which can be downloaded at www.wago.com. There, you can
obtain important information including information on electrical isolation, system
power and supply specifications.
1.2 Copyrights
Copyright (c) 2009 - 2015 ARM LIMITED. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
- Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
- Neither the name of ARM nor the names of its contributors may be used to
endorse or promote products derived from this software without specific
prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

6 Notes about this Documentation WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL COPYRIGHT HOLDERS AND
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Copyright © 2015 STMicroelectronics International N.V.. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted, provided that the following conditions are met:
1. Redistribution of source code must retain the above copyright notice, this
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. Neither the name of STMicroelectronics nor the names of other contributors
to this software may be used to endorse or promote products derived from
this software without specific written permission.
4. This software, including modifications and/or derivative works of this
software, must execute solely and exclusively on microcontroller or
microprocessor devices manufactured by or for STMicroelectronics.
5. Redistribution and use of this software other than as permitted under this
license is void and will automatically terminate your rights under this
license.
THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND
CONTRIBUTORS "AS IS" AND ANY EXPRESS, IMPLIED OR STATUTORY
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT
PERMITTED BY LAW. IN NO EVENT SHALL STMICROELECTRONICS OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

WAGO I/O System 750 XTR Notes about this Documentation 7
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
1.3 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO GmbH & Co. KG, Minden, Germany. Non-observance
will involve the right to assert damage claims.

8 Notes about this Documentation WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
1.4 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.

WAGO I/O System 750 XTR Notes about this Documentation 9
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).

10 Notes about this Documentation WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
1.5 Number Notation
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
1.6 Font Conventions
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under
Start of measurement range
.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.: [F5]

WAGO I/O System 750 XTR Important Notes 11
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
2 Important Notes
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
2.1 Legal Bases
2.1.1 Subject to Changes
WAGO GmbH & Co. KG reserves the right to provide for any alterations or
modifications. WAGO GmbH & Co. KG owns all rights arising from the granting of
patents or from the legal protection of utility patents. Third-party products are
always mentioned without any reference to patent rights. Thus, the existence of
such rights cannot be excluded.
2.1.2 Personnel Qualifications
All sequences implemented on WAGO I/O System 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Fieldbus couplers, controllers and I/O modules found in the modular WAGO I/O
System 750 receive digital and analog signals from sensors and transmit them to
actuators or higher-level control systems. Using controllers, the signals can also
be (pre-) processed.
The devices fulfill the requirements of protection type IP20 and are designed for
use in dry interior spaces. There is protection against finger injury and solid
impurities ≥12.5 mm diameter is assured; protection against water damage is not
ensured.
The devices represent open-type devices. They may only be installed in
enclosures (tool-secured enclosures or operating rooms) which fulfil the listed
requirements specified in the safety instructions in chapter “Safety Advice
(Precautions)”. Use without additional protective measures in environments within
which dust, corrosive fumes, gases or ionized radiation can occur is considered
improper use.
Operating the WAGO I/O System 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in

12 Important Notes WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
the section “Device Description” > “Standards and Guidelines” in the manual for
the used device.
Appropriate housing (per 2014/34/EU) is required when operating the WAGO I/O
System 750 in hazardous environments. Please observe the installation
regulations! Please note that a prototype test certificate must be obtained that
confirms the correct installation of the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F I/O modules within the modular
WAGO I/O System 750. Only these safe F I/O modules ensure functional safety
in accordance with the latest international standards. WAGO's interference-free
output modules can be controlled by the safety function.
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO GmbH
& Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO GmbH & Co. KG.
2.1.4.1 Disposal
2.1.4.1.1 Electrical and Electronic Equipment
Electrical and electronic equipment may not be disposed of
with household waste. This also applies to products without
this symbol.
Electrical and electronic equipment contain materials and substances that can be
harmful to the environment and health. Electrical and electronic equipment must
be disposed of properly after use.
WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary
nationally.

WAGO I/O System 750 XTR Important Notes 13
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
Environmentally friendly disposal benefits health and protects
the environment from harmful substances in electrical and
electronic equipment.
• Observe national and local regulations for the disposal of electrical and
electronic equipment.
• Clear any data stored on the electrical and electronic equipment.
• Remove any added battery or memory card in the electrical and
electronic equipment.
• Have the electrical and electronic equipment sent to your local
collection point.
Improper disposal of electrical and electronic equipment can be harmful to the
environment and human health.
2.1.4.1.2 Packaging
Packaging contains materials that can be reused.
PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout
Europe. Directives and laws may vary nationally.
Environmentally friendly disposal of the packaging protects the environment and
allows sustainable and efficient use of resources.
• Observe national and local regulations for the disposal of packaging.
• Dispose of packaging of all types that allows a high level of recovery,
reuse and recycling.
Improper disposal of packaging can be harmful to the environment and wastes
valuable resources.

14 Important Notes WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
2.2 Safety Advice (Precautions)
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Install device in only one suitable enclosure!
The device is an open system. Install the device in a suitable enclosure. This
enclosure must:
• Guarantee that the max. permissible degree of pollution is not exceeded.
• Offer adequate protection against contact.
• Prevent fire from spreading outside of the enclosure.
• Offer adequate protection against UV irradiation.
• Guarantee mechanical stability
• Restrict access to authorized personnel and may only be opened with tools
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.

WAGO I/O System 750 XTR Important Notes 15
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-471/040-000) must be powered from SELV/PELV power supply(s)!
Inadequate wire cross sections can cause temperature increases!
To avoid increasing thermal risks, only use conductor cross-sections sufficient for
the required maximum load current. The conductor cross-sections specified in
the technical data refer exclusively to the mechanical connection capacity of the
clamping points.
Do not touch hot surfaces!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
System supply only with appropriate fuse protection!
Without overcurrent protection, the electronics can be damaged.
For 24 V system supply input voltage an external fuse, rated max. 2 A, slow
acting, min. 30 VDC shall be used.
Field supply only with appropriate fuse protection!
Without overcurrent protection, the electronics can be damaged.
For 24V field supply input voltage an external fuse, rated max. 10 A, slow acting,
min. 30 VDC shall be used.
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.

16 Important Notes WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
Do not exceed the maximum total current for I/O modules (5 VDC) via data
contacts!
The maximum permissible total current for internal system supply of the I/O
modules may not be exceeded. The permissible total current is specified in the
technical data of the head station and power supply. The data contacts for
internal system supply can be damaged and the permissible operating
temperature can be exceeded by higher values.
When configuring the system, do not exceed the permissible total current. If there
is a higher power requirement, you must use an additional supply to provide the
system voltage (5 VDC)!
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.

WAGO I/O System 750 XTR Important Notes 17
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Use only direct current (DC) for insulation testing!
Both the system voltage and field voltage side are capacitively coupled to the
DIN-rail. If an I/O module is mounted on the DIN-rail, application of an AC voltage
between the DIN-rail and at least one of these two potentials can lead to the
destruction of the module.
Use only direct current (DC) for insulation testing. To avoid destroying the I/O
module, you must discharge it completely before applying the test voltage again.

18 Device Description WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
3 Device Description
The I/O Module 750-471/040-000 (4AI U/I Diff Galv XTR) processes differential
current and voltage signals from the field:
• 0 … 10 V
• ±10 V
• ±200 mV
• 0 … 20 mA
• 3,6 … 21 mA NE43
• 4 … 20 mA
• ±20 mA
The I/O module has four electrically isolated input channels for differential
signals. The sensors are connected to the CAGE CLAMP®terminals +AI 1 and
−AI 1, +AI 2 and −AI 2, +AI 3 and −AI 3, +AI 4 and −AI 4.
The assignment of the connections is described in the “Connectors” section.
Connection examples are shown in section “Connect Devices” > … >
“Connection Example(s)”.
The input signal is electrically isolated and transmitted with a resolution of 16 bits.
The operational readiness and the trouble-free local bus communication of the
channels are indicated via a green function LED.
A red fault LED per channel indicates that the signal is outside the measuring
range and depending on the type of signal additionally an overload or a wire
break.
Details about the individual signal types are described in the “Process Image” >
“Process Data” section.
The meaning of the LEDs is described in the “Display Elements” section.
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node.
An arrangement in groups within the group of potentials is not necessary.
Power to the internal electronics is supplied via internal data bus.

WAGO I/O System 750 XTR Device Description 19
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
Mixed operation
Mixed operation (standard/XTR modules) within a node is possible when groups
of modules are electrically isolated on the field side (i.e., electrically isolated
power supply).
Increased interference!
For standard-compliant application in substation instrumentation and control,
telecontrol systems, railway technology or shipbuilding certified operation,
field-side power supply filter 750-624/040-001 or power supply filter
750-626/040-000 are generally to be used for XTR module groups.
The 750-471/040-000 module can be used with the fieldbus couplers and
controllers of the WAGO I/O System 750 of the specified version or higher listed
in the “Compatibility list” table.
Table 3: Compatibility List 750-471/040-000
Bus System
Fieldbus Couplers/
Controllers
Item No.
Revision Status
– Firmware
PROFINET Fieldbus coupler
750-375
1
750-377
1
PROFIBUS Fieldbus coupler
750-333
20
750-333/040-000
20
Controller
750-833
19
DeviceNet
ECO fieldbus coupler
750-306
4L
ECO-Feldbuskoppler
750-346
11
Controller
750-806
11
CANopen
Fieldbus coupler
750-337
21
750-338
21
ECO fieldbus coupler
750-347
12
750-348
12
Controller
750-837
17
750-838
17
Modbus®
Fieldbus coupler
750-315/300-000
1
750-316/300-000
1
Controller
750-815/300-000
1
750-816/300-000
1
EtherCat
Fieldbus coupler
750-354
3
CC-Link
Fieldbus coupler
750-325
1

20 Device Description WAGO I/O System 750 XTR
750-471/040-000 4AI U/I Diff Galv XTR
Manual
Version 1.0.2
Table 3: Compatibility List 750-471/040-000
Bus System
Fieldbus Couplers/
Controllers
Item No.
Revision Status
– Firmware
ETHERNET
Fieldbus coupler
750-341
9
750-342
18
750-352
10
750-352/040-000
10
750-362
2
750-363
3
750-363/040-000
3
750-364/040-010
3
750-365/040-010
3
Controller
750-823
3
750-841
21
750-842
19
750-843
3
750-852
10
750-871
9
750-872
5
750-873
5
750-880
10
750-880/040-000
10
750-881
10
750-882
10
750-885
10
750-890
2
750-890/040-000
5
750-891
2
750-893
3
Controller BA
750-884
10
Controller PFC100
750-810x
10
Controller PFC200
750-82xx
10
750-82xx/040-00x
10
Fieldbus
coupler
Fieldbus coupler
750-330
9
750-332
2
Controller
750-829
9
750-830
9
750-831
9
750-832
2
KNX Controller
750-849
9
750-889
10
Other fieldbus couplers/controllers on request!