Wall Bed Factory Mission User manual

Wall Bed Factory
Assembly Instructions
Camden
Murphy Bed
Farmhouse
Murphy Bed
Hudson
Murphy Bed
Mission Horizontal
Murphy Bed
Mission
Murphy Bed

WallbedFactory.com
Assembly Instructions
Page 2 of 19
1.800.975.8451
Tube Leg Murphy Beds
**Please make sure all hardware is included. If anything is missing call 1.800.975.8451.
A.
B.
Leg Installation Parts
A. Right-Facing Leg (1)
B. Left-Facing Leg (1)
C. Machine Screws (8)
(NOTE: Machine Screws are
pre-screwed into Bed Frame.)
B.
D.
C.
E.
A.
Items Not to Scale
INCLUDED HARDWARE:
Bed Installation Parts
A. Air Pistons (2)
B. 3” Sheet Rock Screws (4)
C. 1 5/8” Hexagonal Screws (4)
D. 1 1/2” Zinc Screws (4)
E. Allen Wrench
OPTIONAL: Hardware Kit for Metal
Stud/Masonary Walls
TOOLS NEEDED:
A. Stud Finder
B. Flathead Screwdriver
C. Power Drill w/ Phillips Head Screwdriver Bit & Drill Bits
A.
B.
Phillips Head
Screwdriver Bit
C.

WallbedFactory.com
Assembly Instructions
Page 3 of 19
1.800.975.8451
Tube Leg Murphy Beds
PART A: Assembling Wall Bed
Step 1:
Remove Wall Bed from packaging (package includes 5 bed pieces). Retrieve 2 blue-green Foam
Pieces from Side Panel packaging to use in a later step.
Determine where you want to position Wall Bed. Place Head of Bed 18” from wall. Lay out other
pieces as shown below.
Bed Frame
Crown
Headboard
Right Side Panel
Left Side Panel
Head of Bed
Foot of Bed
Foam Pieces
18” from wall

WallbedFactory.com
Assembly Instructions
Page 4 of 19
1.800.975.8451
Tube Leg Murphy Beds
Step 2:
PARTS NEEDED: STUD FINDER, PENCIL, MEASURING TAPE
Use Stud Finder to find and mark location of 2-4* studs along wall across width of Wall Bed.
Placement of marks will depend on bed size/type. Mark studs on wall at the following heights:
Vertical Beds Horizontal Beds
Twin 84” Twin 48”
Twin XL 88” Twin XL 48”
Full 84” Full 64”
Queen 88” Queen 68”
King 88” King 86”
Cal King 92” Cal King 82”
To locate studs:
1. Slide Stud Finder along wall behind Wall Bed until lights indicate a stud beneath.
2. Draw a line at this point.
3. Slide Stud Finder along wall in opposite direction, toward your line. When light indicates the
other side of same stud, make a second line.
4. Mark an “x” between the 2 lines. This is the middle of the stud.
5. Repeat steps 1-4 until you have identified and
marked 2-4* studs on wall behind Wall Bed.
18” from wall
See chart above to determine how
many inches from floor to mark studs.
*The number of studs in wall behind bed will
vary depending on size of bed: Twin, 2 studs;
Full/Queen, 3 studs; King, 4 studs.

WallbedFactory.com
Assembly Instructions
Page 5 of 19
1.800.975.8451
Tube Leg Murphy Beds
E-clip
Step 3:
PARTS NEEDED: FLATHEAD SCREWDRIVER
Remove E-clip from Right Side Panel (see A) by inserting Flathead Screwdriver between E-
clip and Pivot Bar and rotating screwdriver 90° (see B).
A.
B.

WallbedFactory.com
Assembly Instructions
Page 6 of 19
1.800.975.8451
Tube Leg Murphy Beds
Step 4:
Lift Right Side Panel onto its long edge (see A) and slide toward Bed Frame, inserting Pivot
Bar through metal plate on Bed Frame (see B).
Right Side Panel
A.
B.
Bed Frame
Bed Frame

WallbedFactory.com
Assembly Instructions
Page 7 of 19
1.800.975.8451
Tube Leg Murphy Beds
Step 5:
Put E-clip back on Pivot Bar by sliding E-clip into grooves on Pivot Bar until it snaps into place.
E-clip
Step 6:
Repeat steps 3-5 on left side of bed for Left Side Panel installation. Both Side Panels are now
attached to Bed Frame.
Right Side Panel
Left Side Panel
Bed Frame
Right Side Panel
Bed Frame

WallbedFactory.com
Assembly Instructions
Page 8 of 19
1.800.975.8451
Tube Leg Murphy Beds
Bed Frame
Pop Piston Head at narrow end of Air Piston onto Pivot Ball on Plate on Right Side of Bed Frame.
Step 8:
PARTS NEEDED:2 AIR PISTONS
Piston Head
narrow end
wide end
Piston Head
Foot of Bed
bumper
bumper
Step 7:
PARTS NEEDED:FOAM BLOCKS
At Foot of Bed, pivot both Side Panels slightly out and away from Bed Frame so bumpers on Side
Panels are out of way. Lift Foot of Bed 6” to 8” and slide Foam Blocks underneath to keep Bed
Frame elevated for the following steps.
Bed Frame

WallbedFactory.com
Assembly Instructions
Page 9 of 19
1.800.975.8451
Tube Leg Murphy Beds
Step 10:
Repeat Step 8-9 to install second Air Piston on left side of bed.
Step 9:
Have your helper stand at Foot of Bed and raise/lower Bed Frame (see A) to align Piston Head at
wide end of Air Piston with Pivot Ball on Side Panel Plate, while you Pop Piston Head onto Pivot Ball
(see B).
A.
B.