WallboxOK EV PORTABLE TYPE1 Manual

WALLBOX EV PORTABLE
USER MANUAL
INSTALLATION MANUAL
Online Manual
http://goo.gl/lL2jI1

2
WALLBOXOK bears the CE mark. The corresponding
Declarations of Conformity are located at
WallboxOK.
This product metes the requirements of the
ROHS Directive (2011/65/CE). The corresponding
Declarations of Conformity are located at
WallboxOK.
Disposal information
The above symbol indicates the selective collection of electrical and
electronic equipment (EEE) once its useful life has ended so that it enters
the recycling circuit, and does not end up in unauthorized garbage
containers. Therefore, the electrical and electronic equipment of the
electric charging station, as well as its accessories, must be disposed of
separately from household waste. The instructions can be found on the
product, in the instructions for use or on the packaging. The materials can
be reused in accordance with their marking. The reuse, the recycling of
materials and other forms of reuse of used equipment contribute
considerably to protect our planet.

3
1 INDEX
1 ÍNDEX....................................................................................................................................... 3
2 IMPORTANT INFORMATION.................................................................................................... 4
2.1 SAFETY INSTRUCTIONS.................................................................................................... 4
2.2 INTENDED USED ................................................................¡Error! Marcador no definido.
2.3 ABOUT THIS MANUAL ..................................................................................................... 5
3 OVERVIEW............................................................................................................................... 6
3.1 VERSION OVERVIEW..........................................................¡Error! Marcador no definido.
3.2 VERSIONS ........................................................................................................................ 6
VERSIONS .................................................................................................................................... 6
4 USING DE CHARGING STATION. .............................................................................................. 7
4.1 ELECTRICAL CHARGING STATION WITH CABLE ............................................................... 7
4.2 CHARGING SPEED SELECTION ...........................................¡Error! Marcador no definido.
4.3 ACCESS TO CHARGING MENU ............................................................................................... 9
ANOMALIES SOLUTION. ................................................................................................................ 10
5 INSTALLATION GUIDELINES................................................................................................... 11
5.1 GENERAL CRITERIA FOR THE SITE SELECTION FOR WHERE TO INSTALL DE CHARGING
CABLE............................................................................................................................. 11
5.2 SPECIFICATION FOR THE ELECTRICAL CONNECTION..................................................... 12
Dear Customer,,
The WallboxOk team, want to thank you for buying one of our Electric Vehicle Charging Box. Our
passion in design and innovation makes our charging points leaders in technology.
Do not hesitate to contact us at inf[email protected] if you have any suggestion.
Hope you enjoy your product
Kind regards,
WallboxOk team

4
2IMPORTANT INFORMATION.
2.1 SAFETY INSTRUCTIONS
WARNING!
Not observing the safety instructions can result in risk of death, injuries and damage to the
device! WALLBOXOK assumes no liability for claims resulting from this.
Electrical hazard / fire hazard! Never use damaged, worn or dirty charging plugs.
The owner must ensure that the charging station is only ever operated in perfect
condition:
-The charging station must be checked regularly for faulty sockets and connectors
and damage to the housing (visual inspection).
-A damaged charging station must be switched off immediately and replaced.
-Repair work to the charging station is not allowed and may only be performed by
the manufacturer (replacement of the charging station).
-Do not carry out any unauthorized conversion work or modifications to the
charging station!
-Do not remove any notices on the device, such as safety symbols, warning notices,
rating plates, nameplates or cable markings!
The charging station does not have its own power switch! The RCD circuit breaker and
the line circuit breaker of the building installation serve as mains disconnector.
No extension cables are permitted for connecting an electric vehicle to the power
supply device for electric vehicles.
Only electrical vehicles or their chargers may be connected. No connection of other
loads is permitted (electric tools etc.)!
chargeRead the information and instructions for your vehicle carefully before you the
vehicle using the charging station.
Ventilation:
A number of vehicles require an external ventilation system in the interior areas due to
the possible creation of toxic or explosive gases during the charging procedure.
Unplug the charging cable by pulling on the connector, never from the cable.

5
Make sure that the load cable is not damaged by mechanical damage (bending,
snagging or crushing) and that the contact area is not exposed to dirt, water or heat
sources.
WARNING!
Risk Damage!
Never clean the charging station using spray water (from a hose, high-pressure
cleaner etc.) to clean the charging station!
2.2 INTENDED USED
THE EV PORTABLE is a "charging station" for the indoor and outdoor area at which electrically
operated vehicles can be charged (e.g. electric automobiles). It can be used portable and allow
you to change the maximum Amps rate..
The respective national regulations must be observed with regard to the installation and
connection of the charging station.
The device was developed, manufactured, inspected and documented in compliance with the
relevant safety standards. Therefore, the products do not pose any danger to the health of
persons or a risk of damage to other property or equipment under normal circumstances,
provided that the instructions and safety precautions relating to the intended use are properly
observed.
The instructions contained in this manual must be followed precisely in all circumstances.
Failure to do so could result in the creation of potential sources of danger or the disabling of
safety devic-es. Apart from the safety instructions given in this manual, the safety precautions
and accident prevention measures appropriate to the situation in question must also be
observed.
2.3 ABOUT THIS MANUAL
This manual is valid for devices of the type: WALLBOX EV PORTABLE
UTILIZATION OF THIS MANUAL
This manual is aimed at the following groups of people:
Final customers (user of the charging point)

10
LCD DISPLAY
CHARGING
Cable IEC 62196 o
SAE J1772
3OVERVIEW.
3.1 VERSION OVERVIEW
WALLBOX EV PORTABLE
3.2 VERSIONS
VERSIONS
Model
Intensity
Power
Supply
Connector Input
Types of
Connector
Type1 16 Amp
6-
16Amp.
Max 3,7 kW
1F+N+TT
CEE 16 Amp
SAE J1772
Type1 32 Amp
6-32
Amp.
Max 7,7 kW
1F+N+TT
CEE 32 Amp
SAE J1772
Type 2 16 Amp
6-16
Amp.
Max 3,7 kW
1F+N+TT
CEE 16 Amp
IEC 62196
Type2 32 Amp
6-32
Amp
Max 22 kW
3F+N+TT
CEE 32 Amp 3 F
IEC 62196
AMPS RATE
BUTTONS
CEE PLUG

10
4USING DE CHARGING STATION.
4.1 CONCONNECT ELECTRICAL CHARGING POINT
1. Plug CEE industrial conector. If necessary you can use the adapters.
2. Wait a few seconds and select the Amp rate with the buttons. PLEASE READ BEFORE
SECTION 4.1 “AMPS RATE SELECTION”!
3. Plug the charging cable into Vehicle.
Starting the charging procedure
1. When the car allows the EVSE start charging, the recharge station will begin to charge.
In the LCD display will show the state of charge.
Ending the charging procedure
The charging procedure is ended by unplugging the charging cable at the vehicle. For
details, please refer to the instructions of the vehicle manufacturer.
Do not use force to pull out a mechanically locked plug.
1. Disconnect the charging cable from the vehicle ("Wait for unplugging").
2. Disconnect the CEE plug.
4.2 SELECTION OF CHARGING SPEED
The recharge selection must be chosen by the client, according to the recharging situation
in which he is and the adapter installed. The screen will guide you on the chosen adapter.
It is always about the maximum recharging speed, if the car does not allow it, this recharge
speed will be reduced.
The recharging intensity can be selected with the equipment at rest (by default) entering
the menu and modifying parameter 1 (See section 4.3) will also allow you to modify the
recharging intensity during charging, allowing you to vary the car's charging power in real
time (only for models that allow it).
ATENTION, BEFORE USING THE EVSE, PLEASE REVISE THIS SETION. THE WRONG USE OF
THE EQUIPMENT CAN DAMAGE THE ELECTRICAL INSTALLATION.

10
SELECT YOUR AMP RATE DEPENDING ON THE ADAPTOR CHOOSEN.
Amps range permited
Charging power (máximum)
CETAC 32 AMPERIOS 400V
6-32 Amp.
IEC 62196: 22 kW
SAE J1772: 7,6 kW
CETAC 32 AMPERIOS 230V
6-32 Amp.
IEC 62196: 7,6 kW
SAE J1772: 7,6 kW
CETAC 16 AMPERIOS 400V
6-16 Amp.
IEC 62196: 11 kW
SAE J1772: 3,7 kW
CETAC 16 AMPERIOS 230V
6-16 Amp.
IEC 62196: 3,7 kW
SAE J1772: 3,7 kW
SCHUKO
6-12 Amp.
IEC 62196: 2,7 kW
SAE J1772: 2,7 kW
All charging stations are supplied with power CETAC 32 Amp. (single or three phase
depending on the output connector). You can purchase as many adapters as needed.
Following the examples:

10
4.3 TROUBLESHOOTING.
A series of parameters can be modified in the equipment menu.
To access the menu we will follow the following procedure:
Without connecting the electric vehicle (idle mode), press the 2 buttons simultaneously. Press until
the menu is accessed. It is necessary between 3-4 seconds.
You can scroll through the menu with the right - left buttons. To exit the menu simply press the
button on the right until we automatically exit the menu. To access it again follow the procedure we
just explained above.
1st Parameter: By default the equipment does not allow to modify the load intensity when the
equipment is loading the vehicle. Modifying this parameter will allow you to modify the curve of the
load intensity while the vehicle is charging. (The vehicle must be compatible with this option so that
the load intensity varied while it is being charged.)
2nd Parameter: Allows you to select the language of the product screen between (Spanish- English
and Portuguese).
Press 3-4 seconds until the menu is
accessed
By default, the recharging intensity will be fixed. To
change to NO, press the button on the right for 3-4
seconds until you see a change in the chosen option
Pressing the right button for 3-4 seconds allows
you to change the language.

10
TROUBLESHOOTING..
PROBLEM
Possible cause
LCD Display does not light up
 No voltage supply.
Check RCD circuit breaker and line circuit breaker
and switch on if necessary..
 Defective –please contact your service partner
Charging procedure is not started
 The plug is not inserted correctly - Pull
out the plug and insert the plug again..
 The connector may be dirty or damaged in the
locking area: clean the connector or order
replacement.
 The vehicle does not need power or has a
problem: check the vehicle.
 The vehicle is scheduled to be charged at a later start
time.
Vehicle is not fully charged
Increased charging time
 - Reduction of the current due to an elevated
temperature due to the vehicle or the electric charging
station.
-Protect the vehicle and the charging station from direct
sunlight during the charging process (porch, parking,
garage ...)
-Visual control of dirt, wear or damage of the connection
device. If necessary, contact your technical assistance
service.
 Incorrect release by external controller (energy
supplier, PV system, ...)



 instalación fotovoltaica…)instalación
fotovoltaica…)
Standard plug cannot be
unplugged
 The loading process has not been completed by the
vehicle: finish the loading process according to the
vehicle manufacturer's manual.
 Eventually the plug can not be unlocked under traction:
press the plug inwards and plug it back into the vehicle.
Then, finish the download process again.

11
5INSTALLATION GUIDELINES.
5.1 GENERAL CRITERIA FOR THE SELECTION OF THE LOCATION WHERE TO INSTALL THE
CHARGER
The recharging point has been built for interiors and exteriors. So it is necessary to foresee the
build conditions and the protection of the build location.
Respect current local regulations for electrical installations, fire prevention and
accident prevention, as well as emergency exits at the location
The installation must only be carried out by qualified personnel.
The electric charging station can not be installed in areas with danger of explosion
(enviromentEX).
Build the charging station in such a way that it is not in the direct path of people,
that nobody can trip over the plugged-in charging cable and that no flow of
pedestrians can step on or cross the charging cable.
Do not build the charging station in a place where it is exposed to ammonia or
ammonia gases (eg in or near stables)).
Do not build the charging station in places where objects could fall and damage the
equipment (ex: ladders or hanging tires).
According to the product standard, the electric charging station must be between 0.4
m and 1.5 m high. It is recommended to mount the electric charging station (cavity or
high connection) at a height of 1.2 m. It should be borne in mind that some national
regulations may limit the height. It must be taken into account, that in case of
placement in parking, put it at a height, that in case of accidental collision, do not
damage the recharging point
Do not expose the device to direct water jets (ex: due to the proximity of manual car
wash stations, high-pressure cleaners, garden hoses)).
If possible, the equipment must be build protected from direct precipitation to avoid,
for example, frost and damage by hail or similar..
As far as possible, the equipment protected from direct sunlight should be build to
prevent the reduction of the load current or the interruption of the load due to high
temperatures in the components of the recharge station.
In case of outdoor installation (ex: in an open-air car park), if the temperature rises
to inadmissible values, please disconnect the recharging point..
Observe the installation regulations of international validity (ex: CEI 60364-1 and CEI 603645-
52) and comply with the installation regulations and current national regulations.

12
5.2 INDICATIONS FOR ELECTRICAL CONNECTION. GENERALITIES
The electric charging station is intended for connection to a cetac outlet.
You must select the recharge intensity according to the chosen adapter.
The plug where the PORTABLE EV is connected will have an existing power line with a fixed
cable and must comply with the current national legal provisions. This line must be protected
by the following protections:
Selection of the RCD circuit breaker (FI):
Each charging station must be connected to a separate RCD circuit breaker. No other
circuits may be connected to this RCD circuit breaker.
The nominal current IN must be selected to match the line circuit breaker and the fuse.
Dimensioning the Line circuit breaker:
For the dimensioning of the circuit breaker switch, the increase in ambient temperatures
in the switch cabinet must also be taken into consideration.
Determine the rated current according to the data on the rating plate, according to
the chosen load power and the power supply line.
Sizing of the power line:
When sizing the installation, do it according to current regulations at the state level. Take into
account the temperatures that the cable may suffer within the recharging point, if it will be
exposed to high temperatures.
Activation and disconnection device:
The electric charging station does not have a power switch. The differential switch and the
circuit breaker switch of the power line act as a network connection device. The recharging
point can always be turned on, turning off only in case of not frequent use.