WamBam Nervous Nelly Vinyl Gate User manual

REALLY
Nervous Nelly
Vinyl Gate
Important stuff to know about
installing your WamBam gate.
CLEVER JOE
Your Installation Buddy
1-877-778-5733
www.wambamfence.com
02.2017

1
Reality Check
For installation videos and more information,
visit www.wambamfence.com
1 - Read Over Fence Instructions First
Your gate and fence will work better together as an integrated
solution if you rst take the time to read and understand your
fence instructions. Especially pay attention to the principles
of anchor installation.
2 - Do a Dry Run First on the Gate Frame
Only (not pickets or boards)
Please do not screw your gate frame together until you have
rst temporarily assembled the gate.
This will ensure four things:
a)
The assembled gate is the correct width as per
the product overview drawing.
b) That you have everything necessary to complete the gate.
c) That you will have assembled the gate in the correct order.
d) All the pieces t and function properly.
It is easier to trouble shoot when things are not screwed together.
3 - Ideally, Install Your Gate Anchors
Before Your Fence Anchors
Your fence panels will be more forgiving for a custom t than
your gate. Ideally, position and install your gate anchors
before you do anything else, or very early on in the
process of setting up your fence run.
Install Your Gate Anchors
Before Installing Your
Fence Anchors.
Conrm Opening Prior
to Final Assembly of
Gate w/Hardware.

2
4 - Ideally, Do Not Hang Your Gate System Off a Single
Non-Supported Post.
Your gate will perform better and last longer if your hinge post is connected to a panel of fence which is
connected to another post. The weight strain will be transferred unto two posts versus just one. Installing
fence panels on both sides of your gate is the ideal in all situations. If this is not possible because of space
restrictions, please see the last two pages of this instruction guide for optional solutions to overcome.
5 - Use Only Large Anchors for All Gate and Hinge Posts.
Regardless of your gate style choice, please use only large anchors for all gate hinge and latch posts .
Your gate will perform better and last longer.



LARGE ANCHOR

SMALL ANCHOR
Do Not Hang Gate on Lone Soldier Post.
For installation videos and more information, visit www.wambamfence.com
In some applications where the gate is going be used heavily, a supporting wheel for this gate
would be advised for strength and durability.
6 - Supporting Wheel?

.090in.wall
thickness
For installation videos and more information, visit www.wambamfence.com
3
Each Gate Box Includes:
• Top Rail (1)
• Vertical Stiles (2)
• Pickets (8)
• Arch Brackets (2)
•
Gate Latch (1)
• Middle Rail (1)
• Gate Brace (1)
• Stainless Steel Screws (24)
• Gate Bottom Brackets (2)
• Gate Hinges (2)
• Bottom Rail (1)
• Gate Jig (1)
• Metal Post Stabilizer (1)
• Tek Screws (4)
Sold Separately:
• Posts
• WamBam Anchors (Large Only)
• Post Caps (3 options)
Box Contents
Nervous Nelly Vinyl Gate
Cap'n Jack Cap'n AmericaCap'n Morgan
.050in.wall
thickness

Nervous Nelly
Vinyl Gate
PRODUCT OVERVIEW
For installation videos and more information, visit www.wambamfence.com
WamBam Anchor
(Large Only)
7.75in.
40.75in.
3.5in.
43.88in.
66.05in.
1.5in.
3.5in. 3.5in.
1.5in.
68in.
61.5in.
50in.
54.5in.
Gate InstallationGate Assembly
B
A B
CD
3.5in.
1.5in.
.090in. wall thickness
C
1.5in.
D
3.5in.
A
1.5in.3.56in.
1.5in.
48in.
46.75in.
7.75in.
Ground
48in.
4in.
42in.
2in.
4
Looking to Do
a Double Gate?
See page 18.

For installation videos and more information, visit www.wambamfence.com
5
B - Identify the location of the metal post stabilizer
and pound flush into the ground
F - Backfill excavated dirt over gate jig
E -
Pound your anchors into place
C - Place vinyl gate jig over the metal post stabilizer
Metal post stabilizer
to be used only
on hinge post
Pegs on the bottom of this anchor
positioner will insert into both
vinyl gate jig and post stabilizer.
See fence instructions if
necessary for more information
on how to install anchors, adjust
leveling donuts and install
vinyl posts.
Bottom of trench
should be level.
Excavate & Install Gate Jig,
Anchors, & Fence Posts
B
D
E
D - Place anchor positioners into gate jig
C
5 1/2in.
Detailed Installation
Instructions
Nervous Nelly Vinyl Gate
F G
STEP 1
A
G - IMPORTANT: Make sure to fasten the
fence panels BEFORE attaching the gate
Dig a Trench 60in.
long x 6in. wide
x 5.5in. deep
A - Identify location of your gate
Temporarily place the anchor positioner into
the metal post stabilizer and determine position.

For installation videos and more information, visit www.wambamfence.com 6
Completely assembled gate shown
Nervous Nelly Vinyl Gate
Assemble the Gate Frame Bottom & Sides
STEP 2
C - Insert vertical gate stiles. They will BOTTOM OUT
against bottom horizontal rail
B C
A
Note that the bottom rail
is Ribbed internally.
B - Insert the bottom rail ALL THE WAY until it
BOTTOMS OUT INSIDE GATE BRACKET
A - Insert the bottom rail ALL THE WAY until it BOTTOMS OUT inside gate bracket
IMPORTANT!
Insert fully to this point.
Insert fully to this point.
Fasten gate brackets to internal
members though inside
of frame using screws.

Insert pickets in the proper
order according to their height
as shown above.
For installation videos and more information, visit www.wambamfence.com 7
A - I nsert pickets through holes in the bottom rail and insert middle rail through pickets
C - Slide gate arch (with brackets) over the
pickets and vertical gate stiles
A
C
Nervous Nelly Vinyl Gate
Insert Pickets & Assemble the Gate Frame Top
STEP 3
B - Insert the top rail inside arch brackets
as illustrated
B
CORRECT 

Insert to this point.
WRONG

For installation videos and more information, visit www.wambamfence.com
8
A
Nervous Nelly Vinyl Gate
Screw Gate Frame/Brackets
STEP 4
A - ENSURE YOUR GATE IS SQUARE and screw brackets as illustrated. The corner-to-corner
measurement must be the same, and the width of the gate should be 48”.
48in.

For installation videos and more information, visit www.wambamfence.com 9
A
A - Fasten gate hinges and gate latch onto the gate brackets with screws
Nervous Nelly Vinyl Gate
Fasten Gate Hinges & Gate Latch
STEP 5
For swimming and other child safety gates, most safety standards specify:
a) Your fence height needs to be between 4’ and 6’ high minimum
b) Your gate needs to open outwards away from the pool
c) Latch releasing mechanism to be minimum 54” off the ground.
*Always confirm these and other requirements with the appropriate authorities
in your area. Code will change from one location to another across the country.
Latch and hinges must be
installed in these exact locations.