WamBam Jiminy Picket User manual

REALLY
Jiminy Picket
Vinyl Gate
Important stuff to know about
installing your WamBam gate.
CLEVER JOE
Your Installation Buddy
1-877-778-5733
www.wambamfence.com
November 2014

1
Reality Check
For installation videos and more information,
visit www.wambamfence.com
1 - Read Over Fence Instructions First
Your gate and fence will work better together as an integrated
solution if you rst take the time to read and understand your
fence instructions. Especially pay attention to the principles
of anchor installation.
2 - Do a Dry Run First on the Gate Frame
Only (not pickets or boards)
Please do not glue or screw your gate frame together until you
have rst temporarily assembled the gate. In other words,
do a dry run rst.
This will ensure three things:
a) That you have everything necessary to complete the gate.
b) That you will have assembled the gate in the correct order.
c) All the pieces t and function properly.
It’s easier to trouble shoot when things are not glued and screwed together.
After you assemble your gate correctly, please disassemble as necessary and
use glue and screws to permanently assemble the gate.
3 - Ideally, Install Your Gate Anchors
Before Your Fence Anchors
Your fence panels will be more forgiving for a custom t than
your gate. Ideally, position and install your gate anchors
before you do anything else, or very early on in the
process of setting up your fence run.
Install Your Gate Anchors
Before Installing Your
Fence Anchors.

2
4 - Ideally, Do Not Hang Your Gate System Off a Single
Non-Supported Post.
Your gate will perform better and last longer if your hinge post is connected to a panel of fence which is
connected to another post. The weight strain will be transferred unto two posts versus just one. Installing
fence panels on both sides of your gate is the ideal in all situations. If this is not possible because of space
restrictions, please contact us for alternative solutions to overcome.
For installation videos and more information, visit www.wambamfence.com



3 For installation videos and more information, visit www.wambamfence.com
103.75 in
2.0 in
2.0 in
1.125 in 1.75 in 1.125 in
Ground
5 - Double Gate Applications:
You can use two standard gates to create wider opening up to 100”. More details are included at the back
of this manual on how this can be accomplished.
120 in [10 ft]
1 5/8 in
WOOD JIG: Purchase separately 4x4 pressure-treated wood and drill holes as illustrated.
(Dispose vinyl jig included with gate kit)
Top View of Wood Jig
Metal Post Stabilizers
Wood Jig
100 in
103.75 in
8.25 in 8.25 in

.090in.wall
thickness
For installation videos and more information,visit www.wambamfence.com
4
Each Gate Box Includes:
• Gate Caps (2)
• T-Brackets (2)
• Gate Hinges (2)
• Picket Caps (7)
• Top Rail (1)
•
Gate Latch (1)
• Vertical Stiles (2)
• Pickets (7)
• Stainless Steel Screws (20)
• Gate Brace (1)
• Gate Bottom Brackets (2)
• Bottom Rail (1)
• Gate Jig (1)
Sold Separately:
• Posts
• WamBam Anchors
• Post Caps (3 options)
Box Contents
Jiminy Picket Vinyl Gate
Cap'n Jack Cap'n America Cap'n Morgan
.050in.wall
thickness
• Tubes of Glue (2)
• Metal Post Stabilizer (1)
• Tek Screws (4)

Jiminy Picket
Vinyl Gate
PRODUCT OVERVIEW
For installation videos and more information, visit www.wambamfence.com
Ground
WamBam Anchor
3.5in.
48in.
7.75in.
24.75in.
4in.
47.5in.
1.5in.
3.5in.
3.5in.
1.5in.
2in.
3in.
22in.
50in.
54.5in.
48in.
48in.
50.5
Gate InstallationGate Assembly
B
A B
C D
3.5in.
1.5in.
.090in. wall thickness
C
1.5in.
D
3.5in.
3.5in.
A
2.89in.
3in.
33in.
5

For installation videos and more information, visit www.wambamfence.com 6
Customize Your
Gate Design
Jiminy Picket Vinyl Gate
Use The Cutting Guide Below To Trim Pickets
to Create A Custom Gate Design
A
B
C
D
37 1/8in.
40 3/8in.
42 3/8in.
43 1/8in.
This Gate Can Also Be Trimmed
Down Both in Width and Height to
Accomodate Custom Applications.
B
A
CD
B
A
C
Please Note:
Cut down the vertical stiles by 6in.

B - Identify the location of the metal post stabilizer
and pound flush into the ground
E - Pound your anchors into place
C - Place vinyl gate jig over the metal post stabilizer
Metal post stabilizer
to be used only
on hinge post
Pegs on the bottom of this anchor
positioner will insert into both
vinyl gate jig and post stabilizer.
See fence instructions if
necessary for more information
on how to install anchors, adjust
leveling donuts and install
vinyl posts.
Bottom of trench
should be level.
Excavate & Install Gate Jig,
Anchors, & Fence Posts
B
D
E
D - Place anchor positioners into gate jig
C
5 1/2in.
A
Dig a Trench 60in.
long x 6in. wide
x 5.5in. deep
A - Identify location of your gate
Temporarily place the anchor positioner into
the metal post stabilizer and determine position.
For installation videos and more information, visit www.wambamfence.com
7
G - IMPORTANT: Make sure to fasten the
fence panels BEFORE attaching the gate
G
F - Backfill excavated dirt over gate jig
Detailed Installation
Instructions
Jiminy Picket Vinyl Gate
F
STEP 1

For installation videos and more information, visit www.wambamfence.com 8
Completely assembled gate shown A - Run bead of vinyl weld continously around
the inside of the gate bracket
C - Insert the bottom rail ALL the way until it
BOTTOMS OUT INSIDE GATE BRACKET
D - Insert vertical gate stiles. They will bottom-
out against bottom horizontal rail
C D
B - Insert the bottom rail ALL THE WAY until it BOTTOMS OUT inside gate bracket
B
Jiminy Picket Vinyl Gate
Assemble the Gate Frame Bottom & Sides
STEP 2
Note that the bottom rail
is ribbed internally.
GLUE
GLUE
Fasten gate brackets
to internal members
though inside of frame
using screws.
Did you do a dry run of assembly first?
Please read page 1 of instructions.
GLUE
Handle with care: vinyl weld
glue takes approximately
five minutes to cure.
A
IMPORTANT!

For installation videos and more information, visit www.wambamfence.com
9
A
A - Run bead of vinyl-weld continously around
the inside of the bracket B - Insert top rail ALL THE WAY until it
BOTTOMS OUT inside bracket
E - Slide brackets with toprail attached down over
the vertical gate stiles
E - Completely assembled gate frame shown
E
B
F
C - Insert rail ALL THE WAY until it BOTTOMS OUT
inside bracket (glue first)
C
Jiminy Picket Vinyl Gate
Assemble the Gate Frame Top & Attach to Sides
STEP 3
D
D - Run a bead of vinyl-weld continuously around
the inside of the brackets
GLUE
GLUE
GLUE
Did you do a dry run
of assembly first?
Please read page 1
of instructions.
IMPORTANT!
IMPORTANT!