Wardrobes Online Chester Series User manual

INSTALLATION INSTRUCTIONS
CHESTER SERIES
1. Lay out one of the side panels and screw Cam ins at the 3 fixed shelf positions.
Repeat the same on the other panel, ensuring the shelf positions match.
Refer to Diagram A for shelf positions.
2. If your tower has drawers, install the receiving drawer runners (refer Diagram A) using the Euro Screws pictured
here. Wheels should face the front of the tower, and be screwed at both the front and back of the runner.
Repeat the same on the other panel, ensuring the drawer runner positions match.
Refer to Diagram A for drawer runner positions.
Screwdriver
Tacks
Adjustable
Shelf
Supports
Cams
Cam
ins
Econo
Brackets
Wall lugs
Screws

3. There are 3 fixed shelves. Insert Cams into the fixed shelves, arrow facing outwards.
4. On one of the side panels, slot the top shelf into the first fixed shelf position. Ensure the white edge of the shelf is
at the front of the tower, and that the cams are facing the ceiling at the top of the tower.
Once the shelf is in place, tighten the cams with screwdriver. Be careful not to overtighten.
Repeat with the middle and lowest fixed shelf, but ensure the cams are facing the floor.
5. Once drawer runners have been installed on both side panels, lower the second side panel into place where Cam
ins meet with fixed shelf Cams. Screw Cams to tighten.
6. Turn tower on to its front, and align the back board with the tower. The white side should be seen, and natural
side faces the wall. Use tacks to secure backboard to the tower. We recommend tacks in each corner and at
every shelf height.

7. Stand tower upright.
Insert Adjustable Shelves at your desired heights using the Adjustable Shelf Supports.
If your system has drawers, install your drawers by angling the drawer upwards (as shown) and lower and level
the drawer as you slide it in. See Drawer Assembly for more information.
For drawers to operate correctly, make sure the wardrobe tower is on a level surface and square to the back wall.
If the floor is not level then floor packers may be required (not included).
8. Now your tower is fully assembled, position the tower in place in your wardrobe and secure to the wall using the
Econo Brackets (supplied). Where possible, fix brackets into studs, or if studs are not available use the Wall lugs
provided. Use a 5mm drill bit. If your system has drawers – it is recommended to secure Econo Brackets under
the shelf above the top drawer, this will be hidden at the very back and will help your system stay square for
efficient drawer operation. Once in place, close the cap cover to conceal the screw.
9. Next you will need to cut and install your top shelf and hanging rails.
Refer to Top Shelf Installation and Hanging Rail Installation for information about installing these into your
wardrobe.
300

S
=
Fixed
Shelf
Position
–
Screw in
Cam Pin
A = Adjustable Shelf Position – insert Adjustable Shelf Support
D = Drawer Position – Screw in Drawer Runner Positions are counted down from the top (includin very top shelf position) For example: 5-S = 5
th
hole down from the top, insert cam pin for Fixed Shelf
1
-
S
A
A
30-S
36-D
2-D
8-D
5 -D
55-S
1
-
S
A
A
30-S
36-D
2-D
8-D
5 -D
55-S
1
-
S
A
A
30-S
36-D
2-D
8-D
5 -D
55-S
1
-
S
A
A
30-S
36-D
2-D
8-D
5 -D
55-S
1
-
S
A
A
30-S
36-D
2-D
A
55-S
1
-
S
A
A
30-S
36-D
2-D
8-D
55-S
1
-
S
A
A
30-S
A
A
55
-
S
1
-
S
A
A
30-S
A
A
55
-
S
1
-
S
A
A
30-S
A
A
55
-
S
1
-
S
A
A
30-S
A
A
55
-
S
Diagram A