Waring WWB3G Series User manual

3-GALLON HOT WATER DISPENSER
DISPENSADOR DE AGUA CALIENTE
DE 3 GALONES (11.35 L)
DISTRIBUTEUR D’EAU CHAUDE
DE 3 GALLONS (11,35 L)
WWB3G SERIES
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea cuidadosamente las instrucciones antes de usarlo.
An que cet appareil vous procure en toute sécurité beaucoup
de satisfaction, lire attentivement le mode d’emploi avant de l’utiliser.

2
TABLE OF CONTENTS
Important Safeguards ........................................................................2
Introduction ........................................................................................3
Parts ....................................................................................................6
Digital Display & Controls ...................................................................7
Unpacking & Installation......................................................................7
Water Hookup, Electrical Hookup ......................................................8
Default Settings ..................................................................................9
Operating Instructions.........................................................................9
Setting the Temperature, Unit of Measure, Clock ..............................9
Water Source ....................................................................................10
Night Mode .......................................................................................10
Cleaning & Maintenance .................................................................. 11
Troubleshooting ................................................................................13
Warranty ...........................................................................................13
IMPORTANT SAFEGUARDS
When using electrical appliances, especially when children are present,
basic safety precautions should always be taken, including the following:
1. READ ALL INSTRUCTIONS.
2. Always unplug from outlet prior to handling or cleaning.
3. Do not touch hot surfaces. Use handles or knobs.
4. Do not move hot water dispenser when it contains hot
water. Completely drain and let the exterior surface cool
before moving.
5. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they are under
supervision or have been given instruction concerning use of
the appliance by a person responsible for their safety.
6. To protect against re, electrical hazards, and/or personal
injury, do not immerse cord, plugs or base in water or
other liquids.
7. Close supervision is necessary when any appliance is used by
or near children.
8. Do not operate any appliance with a damaged cord or plug
or after the appliance malfunctions or has been dropped or

3
damaged in any manner. Return appliance to the nearest
Waring Repair Center for examination, repair, and electrical
or mechanical adjustment.
9. The use of accessory attachments not recommended by
Waring may cause injuries.
10. The appliance is not intended for outdoor use.
11. Do not let cord hang over edge of table or counter or touch
hot surfaces.
12. Do not place on or near a hot gas or electric burner, or in a
heated oven.
13. Do not use appliance for other than its intended use.
14. Scalding may occur if the lid is removed during the lling and
heating process.
15. This hot water dispenser is equipped with a 3-prong grounding
plug and must be plugged into a correctly polarized 3-prong
grounding-type wall receptacle.
16. To reduce risk of electric shock, do not remove or open cover.
No user-serviceable parts inside. Repair should be done by
authorized service personnel only.
17. Do not clean with a water jet or use in an area where a water jet
may be used.
18. To reduce risk of explosion or re, do not use near
combustibles.
19. Do not use extension cords.
20. For safe and proper operation, the appliance must be placed in
a stable, vertical position.
21. To reduce risk of serious burns or scalding, do not place hand
or other body parts under dispenser or container while heating.
22. Always unplug unit from power supply before servicing.
23. Surfaces are hot and can cause burns.
SAVE THESE INSTRUCTIONS
FOR COMMERCIAL USE ONLY
INTRODUCTION
Thank you for purchasing this WaringTM Commercial Hot Water
Dispenser.

4
Features & Benefits
• Hot water dispenser must be plumbed into a water connection.
• Night Mode feature conserves energy and ensures hot water
is ready when you need it.
• Fill rate: approximately 1 gallon per minute when unit is
plumbed-in.
• Initial heat-up time to full capacity: approximately 1.75 hours
(assuming water is at 50°F (10°C) to start)
• Temperature range from 150˚F–205˚F (65˚C–96˚C)
• Hot water dispenser will maintain set water temperature
within +/- 5°F
• Safety Features (Low and High level sensors)
• Tomlinson®No-Drip®tap operation*
• Excess water drain: Easily and safely removes excess water
from below spigot level.
• Low water level sensor: In case water level gets low, an
alarm will sound and the heater will automatically be shut off.
This protects your machine. Once the issue is corrected/more
water added, the alarm will stop
• High-level water sensor: If water level gets too high, an alarm
will sound and the heater will automatically be shut off
• Left and right cup-warming guards
• Removable drip tray for easy and convenient cleaning
GROUNDING INSTRUCTIONS
For your protection, the WaringTM Commercial Hot Water Dispenser
is equipped with a 3-conductor cord set that has a molded 3-prong
grounding-type plug, and should be used in combination with a
properly connected grounding-type outlet, as shown in Figure 1.
If a grounding-type outlet is not available, an adapter, shown in
Figure 2, may be obtained so that a 2-slot wall outlet can be used
with a 3-prong plug. Referring to Figure 3, the adapter must be
grounded by attaching its grounding lug under the screw of the
outlet cover plate.
CAUTION: Before using an adapter, it must be determined that the
outlet cover plate screw is properly grounded. If in doubt, consult a
* Tomlinson®, No-Drip®and the Faucet and Handle configurations are registered trademarks of The Meyer Company, Cleveland, Ohio.

5
licensed electrician. Never use an adapter unless you are sure it is
properly grounded.
NOTE:Use of an adapter is not permitted in Canada.
SHORT CORD INSTRUCTIONS
A short power-supply cord is provided to reduce the risk resulting
from becoming entangled in or tripping over a longer cord.
If a longer detachable power-supply cord or extension cord is used,
(1) the marked electrical rating of the extension cord should be at
least as great as the electrical rating of the appliance, and (2) the
longer cord should be arranged so that it will not drape over the
countertop or tabletop where it can be pulled on by children or
tripped over unintentionally.
The lightning ash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated, dangerous voltage within the
product’s enclosure that may be of sufcient magnitude
to constitute a risk of re or electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Model Electrical Plug Approval
WWB3G 120V, 1440W, 60Hz 5-15P cTUVus

2
4
3
5
9
1
8
6
6
PARTS
1. Housing
2. Guard rails for
warming surface
3. Control panel
4. Digital display
5. Spigot (removable)
6. Spout
7. Power cord (not shown)
8. Overow tray
9. Rubber anti slip feet

7
DIGITAL DISPLAY & CONTROLS
Standby –turns power on and
off to the controls.
Temp/Time –Press to set the
temperature. Press and hold to
set time.
Arrows –Use to adjust settings.
Start –Press to start the heater.
Night Mode –Press to activate
night mode.
Light Bulb –Press to illuminate
the display.
UNPACKING & INSTALLATION
CAUTION: This is a heavy piece of equipment. It is recommended
that moving or lifting the unit be done by two people to avoid injury.
Carefully unpack the machine and make sure there was no damage
during shipping. Contact customer service if you notice any issues.
NOTE: The person installing the appliance is responsible for
ensuring that electric and water connections meet the requirements
of the national electric code, national plumbing code, and any local
ordinances.
INSTALLATION
1. Find a location near a water connection.
2. Remove the hot water dispenser from the packing material.
Remove drip tray from packing material (bottom of package).
3. Carefully stand up the hot water dispenser and place it on a
at, sturdy surface where it will not be knocked into. Be sure to
leave at least 6" (15 cm) from the back of hot water dispenser for
proper venting. Position hot water dispenser so that the faucet
can be easily accessed.
4. Slide the drip tray into slots underneath.
NIGHT
MODE
HEATING
DIGITAL DISPLAY ICONS

8
WATER HOOKUP
NOTE: The hot water dispenser must be installed in compliance
with applicable federal, state and/or local plumbing codes having
jurisdiction. This product requires an approved backow prevention
water device, such as a double check valve, to be installed between
the machine and the water supply. Incoming pressure should be
greater than 30 psi and not more than 70 psi.
NOTE: Connecting the hot water dispenser to a warm water supply
will speed up heating and recovery times.
1. Hot water dispenser is equipped with a ¾" GHT (garden hose
thread) are water inlet tting, which is located on the back of
the unit.
2. Provide shutoff valve and union in supply line near hot water
dispenser.
3. Minimum inlet pressure at hot water dispenser should be 30 psi
and maximum inlet pressure recommended at 70 psi.
4. Turn on the water supply line and check for leaks.
NOTE: A ltering system is recommended to remove odors and
inhibit lime and scale buildup in the unit.
NOTE: In areas with extremely hard water, a water softener must
be installed in order to prevent mineral deposits that may cause
malfunctioning of the equipment.
ELECTRICAL HOOKUP
NOTE: This equipment must be installed in compliance with
applicable federal, state and/or local electrical codes having
jurisdiction. Do not use extension cords. Make sure that the outlet is
properly grounded.
1. Check rating marking on hot water dispenser nameplate to
be sure electric lines match voltage, phase, and amperage
requirements of hot water dispenser. Select the proper cord
and cord grip for electrical rating of the hot water dispenser.
2. For U.S., 120V hot water dispensers are provided with a
120V/15A grounding plug. For Canada, 120V/15A grounding
plug. Units must have a separate 120V/15A outlet. For U.S.,
208/240V hot water dispensers are provided with a 240V/15A
grounding plug.
TESTING THE CONNECTION/BEFORE FIRST USE
1. We recommend running at least one cycle before rst use.
2. Open water supply line valve to hot water dispenser.

9
3. Turn on or plug in the power supply to the hot water dispenser.
The unit lls at the approximate rate of 1 gallon (3.8 L)
per minute, depending on water line pressure.
4. Heat and discard at least one tank of water.
DEFAULT SETTINGS
• Temperature: 150°F/65°C
• Unit of measurement for temperature: Fahrenheit
• Water connection: Plumbed into water supply
• Night mode temperature: xed at 158°F (70°C)
OPERATING INSTRUCTIONS
SETTING THE TEMPERATURE
1. Press
button once.
2. Use the arrows to reach your desired temperature.
3. Once desired temperature is displayed, press the button
to set or wait 10 seconds to set new temperature.
4. Display will show set temperature and PRESS START blinking.
5. Press to begin lling and heating water.
CAUTION: Water is very hot. Use caution when pouring or
transporting hot water. Accidental spills may result in severe burns.
SETTING °F/°C
1. Press
button once.
2. Once in program mode, PRESS and HOLD the button
for 2 seconds.
3. Use the arrows to switch from F to C.
4. Once desired unit of measure is selected, press twice
to set.
5. If neither button is pressed for 15 seconds, then the F or C
displayed will be programmed.
SETTING THE CLOCK
1. To set the clock, press and hold the button for
2 seconds.
2. Use the arrows to scroll.
3. Once the desired time is displayed, wait 10 seconds, and the
time will be set. Display will show set time for 3 seconds.

10
WATER SOURCE
Autofill
1. When in autoll, the autoll icon ashes while unit is lling
with water.
2. The heater will start when water level reaches low-level sensor.
NOTE: If water does not reach the low-level sensor within
5 minutes, error code 6 ashes on screen. See Troubleshooting
section for details.
3. When water reaches temperature, unit will display READY along
with the set temperature.
NIGHT MODE
In Night Mode, unit will maintain water temperature at 158°F/70°C
during non-business hours to save energy and enable a quicker
heat-up time, so that hot water is ready when you need it. When
setting the time for Night Mode, you will be setting the time the unit
will be re-energized and will start heating the water to your pre-set
temperature (e.g., 5:00 am – unit will turn back on and start heating
to 205°F).
1. SETTING TIME for NIGHT MODE
a. PRESS and hold button for 2 seconds:
b. Use the arrows to scroll to the desired time.
c. Once desired time is displayed, wait 10 seconds, and the
time will be set. Display will show set time and for
3 seconds.
2. ENTERING/EXITING NIGHT MODE
a. Pressing button once will enter into Night Mode/Energy
Saving Mode. Display will show the time of day and the .
b. Unit will exit Night Mode and re-energize automatically
at the set time.
c. To exit out of manually, press the button or hold
button for 2 seconds.
a. If button is pressed to exit Night Mode, you must
press to re-energize the unit.
b. If button is pressed to exit Night Mode, unit
will automatically re-energize and start heating to set
temperature.

11
Helpful Hints
Why use Night Mode?
When you need hot water at the start of business, but do not want
your machine on full power during non-business hours. Utilize
Night Mode, an energy-saving feature that will maintain a water
temperature of 158°F/70°C during non-business, and heat to full set
temperature at the time you set.
What time should I set Night Mode to?
Once Night Mode turns off and the machine is re-energized, it will
take approximately 1 hour to reach 205° (MAX), so set the time for
Night Mode for approximately 1 hour before you will need hot water.
Can I change the temperature in Night Mode?
158°F/70°C is the xed temperature and cannot be adjusted.
CLEANING & MAINTENANCE
ALWAYS DISCONNECT OR UNPLUG THE HOT WATER DISPENSER
BEFORE CLEANING. Allow the hot water dispenser to cool
completely before handling or before cleaning.
1. Dispense of any remaining water from the spigot.
2. Wipe exterior and control panel with a nonabrasive, damp cloth
and dry.
• DO NOT use any cleaning uids that can be harmful to you,
others around you, or to the environment.
• DO NOT hose down, immerse or pressure wash any part of
the hot water dispenser.
• NEVER use steel wool or abrasive materials to clean the hot
water dispenser.
• NEVER remove spigot when the hot water dispenser has
water in it. Switch OFF the power to the unit at the circuit
breaker. Turn OFF the water line running to the hot water
dispenser.
NOTE: All sanitizing agents in the food zone must comply with U.S.
Food & Drug Administration Code of Federal Regulations Title 21,
Section 178.1010. Sanitize all food-dispensing units periodically. All
parts to be sanitized must be cleaned rst. Cleaning and sanitizing
frequency must follow state and local health department regulations.
NOTE: Do not use cleansers, bleach liquids, powders, or any other
substance containing chlorine. These products promote corrosion

12
and will pit the stainless steel. USE OF THESE PRODUCTS WILL
VOID THE WARRANTY.
3. Wipe faucet nozzle to remove any mineral deposits. A bristle
brush may be used to remove stubborn mineral build-up.
4. A ltering system is recommended to remove odors and inhibit
lime and scale build up in the unit.
5. In areas with extremely hard water, a water softener must be
installed in order to prevent a malfunctioning of equipment and
in order not to void the warranty.
DAILY
Wipe the outside of the unit with a damp cloth, using soap solution
or a nonabrasive compound when required.
TROUBLESHOOTING CODES
During operation under certain conditions, your machine may display
one of the following error codes. Please follow the chart below to x.
Error
Code Cause Solution
Contact a Service Center if the following error codes appear
E-1
Internal temperature control
damage.
Call a service center for repair or adjustment.
E-2 Machine malfunction. Call a service center for repair or adjustment.
E-3 Heating element damage. Call a service center for repair or adjustment.
E-4 Issue with upper water level
sensor.
Call a service center for repair or adjustment.
E-5 Issue with lower water level
sensor.
Call a service center for repair or adjustment.
User Fixable
E-6
Hot water dispenser does
not have enough water to
begin heating.
Connect to a water source or switch to manual
mode and pour water into the hot water dispenser.
Once water is at proper ll level, alarm will stop and
the machine will begin heating.
Ensure hot water dispenser is on a level surface.
E-7
Water level is too low. Ensure the connection to the water supply is
open and water line pressure is running properly.
If the problem persists, consult customer service
or a local service center.

13
User Fixable (continued)
E-8
Power outage or issue with
power source.
Disconnect plug and reconnect to outlet. Ensure
plug is properly inserted into outlet. Check circuit
breaker and reset.
If the problem persists, consult customer service
or a local service center.
E-9
Water has exceeded MAX ll. Shut off the water supply, drain excess water.
Alarm should go off.
If problem persists, contact a service center.
If this error is seen in manual mode, dispense
some water from the spigot.
If problems persist and the assigned solution does not remedy the
issue, please call Waring Customer Service at 860-496-3100.
NOTE: Any other servicing should be performed by an
authorized service representative.
LIMITED ONE-YEAR WARRANTY
(U.S. AND CANADA ONLY)
Waring warrants every new WaringTM Commercial Hot Water
Dispenser to be free from defects in materials and workmanship
for a period of one year from the date of purchase when used
with foodstuffs, nonabrasive liquids (other than detergents) and
nonabrasive semiliquids, providing it has not been subject to loads in
excess of the indicated rating.
Under this warranty, Waring will repair or replace any part that, upon
our examination, is defective in materials or workmanship, provided
the product is delivered prepaid to the Waring Service Center at
314 Ella T. Grasso Ave., Torrington, CT 06790, or any Factory
Approved Service Center.
This warranty does not: a) apply to any product that has become
worn, defective, damaged or broken due to use or due to repairs
or servicing by other than the Waring Service Center or a Factory
Approved Service Center, or due to abuse, misuse, overloading or
tampering; or b) cover incidental or consequential damages of any
kind. This warranty is void if appliance is used on Direct Current (DC).
WARING COMMERCIAL
314 Ella T. Grasso Ave.
Torrington, CT 06790

14
ÍNDICE
Medidas de seguridad importantes............................................................. 14
Introducción ................................................................................................. 15
Piezas...........................................................................................................18
Pantalla digital y controles ........................................................................... 19
Desembalaje e instalación .......................................................................... 19
Conexión a la red de agua y conexión a la red eléctrica.............................20
Opciones por defecto ..................................................................................21
Instrucciones de operación .........................................................................21
Fijación de la temperatura, de la unidad de temperatura y de la hora........21
Llenado automático .....................................................................................22
Modo nocturno.............................................................................................22
Limpieza y mantenimiento .......................................................................... 23
Resolución de problemas ............................................................................25
Garantía........................................................................................................26
MEDIDAS DE SEGURIDAD
IMPORTANTES
Al usar aparatos eléctricos, especialmente en presencia de niños,
siempre debe tomar precauciones básicas de seguridad, entre ellas las
siguientes:
1. LEA TODAS LAS INSTRUCCIONES.
2. Siempre desenchufe el aparato antes de cualquier manipulación o
mantenimiento, y antes de la limpieza.
3. No toque las superficies calientes; utilice los mangos/asas y los
botones/perillas.
4. No mueva el aparato mientras contenga agua caliente; vacíelo
completamente y espere hasta que la superficie exterior se haya
enfriado antes de moverlo.
5. Los niños o las personas que carezcan de la experiencia o de los
conocimientos necesarios para manipular el aparato, o aquellas cuyas
capacidades físicas, sensoriales o mentales estén limitadas, no deben
utilizar el aparato sin la supervisión o la dirección de una persona
responsable por su seguridad.
6. Para reducir el riesgo de incendio, descarga eléctrica o lesiones, no
sumerja el cable, el enchufe, ni la base en agua ni en ningún otro
líquido.
7. Supervise el uso de este aparato cuidadosamente cuando sea usado
por o cerca de niños.

15
8. No utilice este aparato si el cable o el enchufe están dañados, después
de un mal funcionamiento, después de que se haya caído o si está
dañado; devuélvalo a un centro de servicio autorizado para su revisión,
reparación o ajuste.
9. El uso de accesorios no recomendados por Waring para uso con este
modelo puede causar heridas.
10. Esta unidad no está diseñada para uso en exteriores.
11. No permita que el cable cuelgue del borde de la encimera o de la
mesa, ni que tenga contacto con superficies calientes.
12. No coloque el aparato sobre o cerca de un quemador a gas o de una
hornilla eléctrica caliente, ni en un horno caliente.
13. No utilice el aparato para ningún fin que no sea el indicado.
14. No quite la tapa durante el llenado o el calentamiento; esto puede
causar quemaduras graves.
15. Este aparato cuenta con un cable de puesta a tierra, con enchufe
de tierra, el cual debe ser enchufado en una toma de corriente
debidamente puesta a tierra.
16. Para reducir el riesgo de descarga eléctrica, no abra/quita la carcasa.
Este aparato no contiene ninguna pieza que pueda ser reparada/
cambiada por el usuario. Las reparaciones deben ser efectuadas por
técnicos autorizados solamente.
17. No limpie el aparato a presión/con un chorro de agua, y no lo use en
un lugar donde se use un rociador/chorro de agua.
18. Para reducir el riesgo de explosión o incendio, no lo utilice cerca de
combustibles.
19. No utilice la unidad con un cable de extensión.
20. Coloque siempre la unidad en posición vertical, sobre una superficie
estable, para garantizar un funcionamiento adecuado y seguro.
21. Para reducir el riesgo de quemaduras o escaldaduras graves, no
coloque la mano ni ninguna otra parte del cuerpo debajo de la unidad
o del grifo mientras el agua se esté calentando.
22. Siempre desenchufe la unidad antes de realizar cualquier trabajo de
mantenimiento.
23. Las superficies de la unidad se ponen muy calientes y pueden causar
quemaduras.
GUARDE ESTAS INSTRUCCIONES
PARA USO COMERCIAL
SOLAMENTE

16
INTRODUCCIÓN
Gracias por comprar el dispensador de agua caliente Waring™
Commercial.
Características técnicas
• Este dispensador de agua caliente debe conectarse al agua
corriente.
• El modo nocturno ahorra energía y asegura que el agua
caliente esté lista cuando la necesite.
• Velocidad de llenado: aproximadamente 1 galón (3.8 L)
por minuto.
• Tiempo de calentamiento inicial a plena capacidad: aprox.
• 1.75 horas (si el agua de llenado está a 50° F/10 °C).
• Temperatura variable desde 90 °F (32 °C) hasta 205 °F (96 °C)
• El dispensador de agua caliente mantiene la temperatura del
agua dentro de los 5 °F (3 °C).
• Características de seguridad:
• Grifo antigoteo Tomlinson®No-Drip®*
• Sistema de drenaje: permite vaciar el agua que se encuentra
por debajo del nivel del grifo de forma fácil y segura.
• Sensor de nivel de agua bajo: si el nivel del agua es
demasiado bajo, se activa una alarma y la resistencia se apaga
automáticamente para evitar daños a la unidad. Una vez que se
agrega agua, la alarma se detiene
• Sensor de nivel de agua alto: si el nivel del agua es
demasiado alto, se activa una alarma y la resistencia se apaga
automáticamente.
• Protecciones alrededor del calentador de tazas
• Bandeja de goteo removible para una limpieza fácil y práctica
INSTRUCCIONES DE PUESTA A TIERRA
Para su protección, su aparato está equipado con un cable de puesta
a tierra, con clavija de tierra, la cual debe ser conectada a una toma de
corriente debidamente puesta a tierra (Fig. 1). Si una toma de corriente con
toma de tierra no está disponible, se podrá usar un adaptador para conectar
el aparato a una toma de corriente sin toma de tierra (Fig. 2). El adaptador
debe ser puesto a tierra mediante un tornillo de metal que conecte la
lengüeta del adaptador a la placa de la toma de corriente (Fig. 3).
*Tomlinson®, No-Drip®y la configuración del grifo y de la manija son marcas registradas de The Meyer Company, Cleveland, Ohio

17
PRECAUCIÓN: antes de enchufar el adaptador, cerciórese de
que la toma de corriente está puesta a tierra. Si no está seguro/a,
comuníquese con un electricista. Nunca use un adaptador sin estar
seguro/a de que la toma de corriente esté puesta a tierra.
NOTA:está prohibido usar un adaptador en Canadá.
USO DE EXTENSIONES
El cable provisto con este aparato es corto, para reducir el riesgo de
que alguien se enganche o tropiece con un cable más largo.
Se podrá usar una extensión eléctrica o un cable removible más
largo, siempre que (1) la clasificación nominal de la extensión o
del cable sea por lo menos igual a la del aparato y que (2) el cable
más largo o la extensión sean acomodados de tal manera que no
cuelguen de la encimera/mesa, donde pueden ser jalados por niños
o causar tropiezos.
El símbolo de relámpago con punta de flecha dentro de un
triángulo equilátero tiene como fin alertar al usuario de la
presencia de voltajes peligrosos no aislados en el interior del
aparato, los cuales pueden ser de suficiente magnitud para
constituir un riesgo de incendio o descarga eléctrica.
El signo de exclamación dentro de un triángulo equilátero
tiene como fin alertar al usuario de la presencia de
instrucciones importantes de operación y mantenimiento
(servicio) en la documentación que acompaña al equipo.
Modelo Especificaciones Enchufe Certificación
WWB3G 120 V, 1440W, 60Hz 5-15P cTUVus

2
4
3
5
9
1
8
6
18
PIEZAS
1. Carcasa
2. Barras de protección
alrededor del calentador
de tazas
3. Panel de control
4. Pantalla digital
5. Grifo removible
6. Pico
7. Cable (no ilustrado)
8. Bandeja de goteo
9. Pies de goma antideslizantes

19
PANTALLA DIGITAL Y
CONTROLES
Botón STANBY –Enciende/apaga
los controles.
Botón TEMP/TIME –Permite
ingresar al modo de ajuste.
Mantenga el botón oprimido para
fijar la hora.
Flechas +/– –Permiten fijar y
cambiar la temperatura y la hora.
Botón START –Enciende la
resistencia.
Botón NIGHT MODE –Oprímalo
para activar el modo nocturno.
Botón “bombilla” –Oprímalo para
iluminar la pantalla.
DESEMBALAJE E INSTALACIÓN
PRECAUCIÓN: este aparato es pesado; es aconsejable moverlo
o levantarlo entre dos personas para evitar lesiones. Desembale la
unidad con cuidado y cerciórese de que no se ha dañado durante el
transporte. En caso de problemas, póngase en contacto con nuestro
servicio de atención al cliente.
NOTA: es responsabilidad del instalador del aparato asegurarse de
que las conexiones eléctricas y de agua cumplan con los requisitos
del código eléctrico nacional, el código nacional de plomería y
cualquier ordenanza local.
INSTALACIÓN
1. Coloque el aparato cerca de una conexión de agua.
2. Saque la unidad del material de embalaje.
Saque la bandeja de goteo del material de embalaje (en el fondo
de la caja).
3. Con cuidado, enderece la unidad y colóquela sobre una
superficie plana y sólida donde no haya riesgo de chocar
con ella. Asegúrese de dejar un espacio libre de al menos
6 pulgadas (15 cm) atrás de la unidad para asegurar una
ventilación adecuada. Coloque la unidad de manera que el grifo
sea fácilmente accesible.
NIGHT
MODE
HEATING
DIGITAL DISPLAY ICONS

20
4. Deslice la bandeja de goteo en las ranuras situadas debajo de la
unidad.
CONEXIÓN A LA RED DE AGUA
NOTA: este aparato debe ser instalado de acuerdo con los códigos
de plomería nacionales, regionales o locales aplicables. Requiere un
dispositivo antireflujo aprobado, tal como una válvula antirretorno doble,
entre la unidad y la conexión de agua. La presión de entrada debe estar
entre 30 psi y 70 psi.
NOTA: conectar el aparato a una fuente de agua caliente reduce el
tiempo de calentamiento y recuperación.
1. El dispensador de agua caliente cuenta con una conexión de
entrada ensanchada tipo NH (rosca de manguera de jardín) de ¾ in.
(19 mm), situada en la parte posterior de la unidad.
2. Proporcione una válvula de cierre y una conexión en la línea de
suministro de agua cerca de la unidad.
3. La presión de agua debe estar entre 30 psi y 70 psi.
4. Abra el suministro de agua y compruebe que no hay fugas.
NOTA: se recomienda utilizar un sistema de filtración para eliminar los
olores y evitar la acumulación de cal y sarro en el depósito de agua.
NOTA: en áreas donde el agua es extremadamente dura, se debe
instalar un ablandador de agua para evitar depósitos minerales que
puedan interferir con el buen funcionamiento de la unidad.
CONEXIÓN A LA RED ELÉCTRICA
NOTA: este aparato debe instalarse de acuerdo con los códigos
nacionales, regionales y locales aplicables. No utilice la unidad con
un cable de extensión. Cerciórese de que la toma de corriente está
correctamente conectada a tierra.
1. Chequee las especificaciones eléctricas del dispositivo, indicadas
en su placa de especificaciones técnicas, y asegúrese de que la
línea eléctrica utilizada corresponde a la tensión, fase y amperaje
requeridos. Asegúrese de utilizar el cable y el enchufe correctos.
2. Los modelos de 208/ 240V destinados al mercado norteamericano
cuentan con un enchufe de conexión a tierra de 240V/15 A. En
Canadá, cuentan con un enchufe de conexión a tierra de 120 V / 20
A. Siempre conecte el cable a una toma de corriente independiente.
Los modelos de 208/ 240V destinados al mercado norteamericano
cuentan con un enchufe de conexión a tierra de 240V/15 A.