WASAGUN CWG001 User manual

If you need assistance or find missing or damaged parts
in the package, contact us by mail: [e-mail]
12
Screwdriver
Assembly Instructions - Please keep for future reference
Dog Cage
CWG001
Dimensions
Width - 27.17inch
Depth -20.87inch
Height - 23.62inch
Assembly Tool
Required
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
Brand:WASAGUN 123
45
2PCS1PCS
1PCS
1PCS1PCS
M6x25mm
AC
24PCS
1PCS
6
7
1PCS2PCS
9
2PCS
1PCS
10
1PCS
8
B
2PCS
ST4x10mm
11
1PCS
D
4PCS
M6x20mm
E
4PCS
If you need assistance or find missing or damaged parts
in the package, contact us by mail: [e-mail]
Components
Please check all parts below under a good condition before you install the dog cage.
*The number of screws refers to the screws actually needed, but we will add some more screws as reserve.

6
5
5
AX4
E
A
AX4 EX1
4
9
3
AX8 EX1
AX4
AX8
E
A
1
2
AX4
E
A
AX4 EX1
5
6
50%
100%
lock out
4
Assembly Instructions
Step 1
Assemble and secure No. 5 and No. 6 with screw A.
Step 2
Assemble No. 5/6 and No. 1/2 (lock out) with A screw (lock 50% first).
Assembly Instructions
Step 3
Step 4
Attach No.3 and No.9 to the assembled assembly using screw A.
Please note No.9 needs to distinguish the direction, the hole far
away from the edge is installed downward.
Assemble No. 1/2 and No. 4 with A screw. Finally ALL are fixed 100%.
E
A
lock out
AX4 EX1
Properly mounted,
the tip is parallel.
2
1

AX4 EX1
AX4
CX2 EX1
C
11
E
8
DX4
8
7
BX4 EX1
E
B
BX4
D
Assembly Instructions
Step 5
Assembly Instructions
Step 7
Step 6 Step 8
Assemble and secure No. 7 and No. 8 with screw B.
Assemble the No. 8 assembly on the assembled assembly using screw A. Assemble the adjusting feet on the four feet, the foot can be adjusted to the height of 15mm, the four
feet need to be adjusted to use, to prevent shaking!
Assemble No. 11 at the corresponding position in the socket slot with C screw.
The raised holes face outward
E
A
Socket holes are placed backward.

10
Assembly Instructions
Step 9
Place No.10 under the bottom frame card slot and the assembly is complete.
Assemble on a soft level surface to
avoid damaging the unit or your
floor.
Don't overload the dog cage.
Do not use a power
drill/screwdriver for
inserting screws, as it
can cause screws to
break or strip.
1 2
Do not allow your child to stand or
climb on the dog cage, this may
make it top-heavy and cause the
device to break or topple over.
Assemble the item as close to its
final position (in the same room) as
possible.
Do not place furniture directly infront
of radiators, fires or any other
source of heat.
Check that if you have all the
components and tools listed on the
front cover and pages 2.
Remove all fittings from the plastic
bags and separate them into
their groups.
Keep children and animals away
from the work area, small parts
could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Safety Notes and Care Avice
Important – Please read these instructions fully before starting assembly
Parts of the
assemble will be
easier with 2 people.
Dispose of all packaging carefully
and responsibly.
Safety Notes and Care Avice
Important – Please read these instructions fully before starting assembly
Clean with mild soap on a damp ,
soft rag. Rinse and dry
thoroughly. Do not use abrasive
chemicals for cleaning.
Please check if there any loose screws
on the unit from time to time.
This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
Regular dusting with a dry cloth will
keep your units
Clean marks with a damp cloth.
Do not allow spillages to stay on the
surface
To remove stubborn stains, wipe with a
damp cloth and washing up
Do not use abrasive cleaners.
Do not clean with products contaiing the
following: Acetone, (e. g nail varnish
remover). Ammonia (e. g. bleach).
orSodium hydroxide (e. g. Caustic soda,
drain and oven cleaners).
In the event of accidental contact with
aggresive cleaners, rinse thoroughly with
water.
To remove stains and small scratches
use a car polish or light cutting
compound.
Use place mats to protect the surface
from moisture and heat.
General care and maintenance
Cleaning and care of high gloss surfaces
WARRANTY
Thank you for choosing WASAGUN product. We sincerely hope that you are satisfied with it.
The manufacturer's warranty covers the product for a period of 24 months from the date of purchase
against manufacturing faults. All warranties are automatically kept track of in our system, so there is no
need to register your product.
Agent/Distributor is welcome to contact us. Email:[email protected].
Any help or questions during use, please contact us via website www.wasagun.com, send email to
[email protected], we will service you within 24 hours. We suggest to provide a warranty card, a
photo or a video if there’s broken spare part or not working machine so that we can be much more clear
about your problems and offer you the best solution.
Please fill in the table and email it within 10 days from the date of purchase.
Manufacturers:DongGuan HangXing Houseware co.,Ltd
Add.:Building 5, No. 6 Heshi Road, Qiaotou, Dongguan City, Guangdong
Contact：Carl Tel：[phone] E-Mail： [email protected].