Water Furnace Envision NSW018 series Service manual

IM1006WN 08/13
Installation Information
Water Piping Connections
Electrical Data
Startup Procedures
Preventive Maintenance
NSW Installation Manual
Geothermal Hydronic Heat Pump
1.5 to 6 Tons

NSW INSTALLATION MANUAL
Table of Contents
Model Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Water Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Field Connected Water Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
Potable Water Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Hydronic Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Accessories and Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-15
Wiring Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16-19
External Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-21
Converting to a Dedicated Cooling Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Unit Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Standard Board - Control Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-25
Standard Control - Panel Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27
Reference Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Legend and Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
AHRI/ISO 13256-2 Performance Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Pressure Drop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Operating Limits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Physical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Flow Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Thermistor and Compressor Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Operating Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Antifreeze Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Troubleshooting Guideline for Refrigerant Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Heating and Cooling Cycle Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Troubleshooting Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-38
Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Revision Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

4
NSW INSTALLATION MANUAL
Model Nomenclature
All Envision Series product is safety listed under UL1995 thru ETL and performance
listed with AHRI in accordance with standard 13256-1. The Envision Series is also
ENERGY STAR
®
rated.
N S W 050 * 1 0 R C
3 4-6 7 8 9 10 11
Model
N – Envision Hydronic
Heat Pump
Compressor Type
S – Single Speed
Cabinet Configuration
W – Water-to-Water
Unit Capacity
018, 025, 040, 050, 060, 070
Vintage
* - Factory Use Only
Voltage
1 – 208-230/60/1
Hot Water Option1
0 – No Hot Water Generation
2 – Hot Water Generation
IntelliStart®
N – None
A – IntelliStart
Controls Option
S – Microprocessor
Future Option
0 – Standard
Future Option
S – Standard
Future Option
S – Standard
Water Coil Option2
C – Copper
N - CuproNickel
L – Source CuproNickel & Load Copper
S – Source Copper & Load CuproNickel
Reversible Option
H – Heating Only
R – Reversible
Rev.:
11 July 2013D
S
12
NOTES: 1 – Available on 040, 050, 060, and 075 only. Hot water generator requires field installed external pump kit.
2 – NSW018 and NSW025 heating only models are available only with copper double wall vented load coax for potable water.
21
S 0 S N
13 14 15 16

5
NSW INSTALLATION MANUAL
Safety Considerations
Installing and servicing air conditioning and heating
equipment can be hazardous due to system pressure and
electrical components. Only trained and qualified service
personnel should install, repair or service heating and air
conditioning equipment. When working on heating and
air conditioning equipment, observe precautions in the
literature, tags and labels attached to the unit and other
safety precautions that may apply.
Follow all safety codes. Wear safety glasses and work
gloves. Use quenching cloth for brazing operations. Have
fire extinguisher available for all brazing operations.
NOTE: Before installing, check voltage of unit(s) to ensure
proper voltage.
WARNING: Before performing service or
maintenance operations on the system, turn off
main power switches to the unit. Electrical shock
could cause serious personal injury.
Process Water Applications
For process water applications, it is recommended that
a secondary load heat exchanger be installed to prevent
corrosion to the unit’s primary coaxial coil. In situations
where scaling could be heavy or where biological growth
such as iron bacteria will be present, a closed loop system is
recommended. Over a period of time, ground water unit heat
exchanger coils may lose heat exchange capability due to a
buildup of mineral deposits. These can be cleaned only by
a qualified service mechanic as special pumping equipment
and solutions are required. Never use flexible hoses with a
smaller inside diameter than that of water connections.
Moving and Storage
Move units in the normal “Up” orientation as indicated by
the labels on the unit packaging. When the equipment
is received, all items should be carefully checked against
the bill of lading to ensure that all crates and cartons
have been received in good condition. Examine units for
shipping damage, removing unit packaging if necessary
to properly inspect unit. Units in question should also
be internally inspected. If any damage is observed, the
carrier should make the proper notation on delivery receipt
acknowledging the damage. Units are to be stored in a
location that provides adequate protection from dirt, debris
and moisture.
General Installation Information
WARNING: To avoid equipment damage, do not
leave the system filled in a building without heat
during cold weather, unless adequate freeze
protection levels of antifreeze are used. Heat
exchangers do not fully drain and will freeze
unless protected, causing permanent damage.
Unit Location
Provide sufficient room to make water and electrical
connections. If the unit is located in a confined space,
provisions must be made for unit servicing. Locate the
unit in an indoor area that allows easy removal of the
access panels and has enough space for service personnel
to perform maintenance or repair. These units are not
approved for outdoor installation and, therefore, must be
installed inside the structure being conditioned. Do not
locate units in areas subject to freezing conditions.
WARNING: Do not store or install units in
corrosive environments or in locations subject
to temperature or humidity extremes (e.g. attics,
garages, rooftops, etc.). Corrosive conditions and
high temperature or humidity can significantly
reduce performance, reliability, and service life.
Mounting Units
Prior to setting the unit in place, remove and discard the
compressor hold down shipping bolt located at the front of
the compressor mounting bracket.
Units should be mounted level on a vibration absorbing pad
slightly larger than the base to provide isolation between
the unit and the floor. It is not necessary to anchor the unit
to the floor. Allow access to the front, back, and side access
panels for servicing.
DWP`ObW]\>OR;]c\bW\U

6
NSW INSTALLATION MANUAL
General
NSW water-to-water heat pumps may be successfully
applied in a wide range of residential and light commercial
applications. It is the responsibility of the system designer
and installing contractor to ensure that acceptable water
quality is present and that all applicable codes have been
met in these installations. Failure to adhere to the guidelines
in the water quality table could result in loss of warranty.
Water Treatment
Do not use untreated or improperly treated water.
Equipment damage may occur. The use of improperly
treated or untreated water in this equipment may result in
scaling, erosion, corrosion, algae or slime. The services of a
qualified water treatment specialist should be engaged to
determine what treatment, if any, is required. The product
warranty specifically excludes liability for corrosion,
erosion or deterioration of equipment.
The heat exchangers and water lines in the units are copper
or cupronickel tube. There may be other materials in the
Material Copper 90/10 Cupronickel 316 Stainless Steel
pH Acidity/Alkalinity 7 - 9 7 - 9 7 - 9
Scaling Calcium and
Magnesium Carbonate
(Total Hardness)
less than 350 ppm
(Total Hardness)
less than 350 ppm
(Total Hardness)
less than 350 ppm
Corrosion
Hydrogen Sulfide Less than 0.5 ppm (rotten egg
smell appears at 0.5 ppm) 10 - 50 ppm Less than 1 ppm
Sulfates Less than 125 ppm Less than 125 ppm Less than 200 ppm
Chlorine Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm
Chlorides Less than 20 ppm Less than 125 ppm Less than 300 ppm
Carbon Dioxide Less than 50 ppm 10 - 50 ppm 10 - 50 ppm
Ammonia Less than 2 ppm Less than 2 ppm Less than 20 ppm
Ammonia Chloride Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm
Ammonia Nitrate Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm
Ammonia Hydroxide Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm
Ammonia Sulfate Less than 0.5 ppm Less than 0.5 ppm Less than 0.5 ppm
Total Dissolved Solids (TDS) Less than 1000 ppm 1000 - 1500 ppm 1000 - 1500 ppm
LSI Index +0.5 to -0.5 +0.5 to -0.5 +0.5 to -0.5
Iron Fouling
(Biological Growth)
Iron, FE2+ (Ferrous)
Bacterial Iron Potential < 0.2 ppm < 0.2 ppm < 0.2 ppm
Iron Oxide Less than 1 ppm, above this
level deposition will occur
Less than 1 ppm, above this
level deposition will occur
Less than 1 ppm, above this
level deposition will occur
Erosion
Suspended Solids Less than 10 ppm and filtered
for max. of 600 micron size
Less than 10 ppm and filtered
for max. of 600 micron size
Less than 10 ppm and filtered
for max. of 600 micron size
Threshold Velocity
(Fresh Water) < 6 ft/sec < 6 ft/sec < 6 ft/sec
NOTES: Grains = ppm divided by 17
mg/L is equivalent to ppm
2/22/12
Water Quality
building’s piping system that the designer may need to take
into consideration when deciding the parameters of the
water quality.
If an antifreeze or water treatment solution is to be used,
the designer should confirm it does not have a detrimental
effect on the materials in the system.
Contaminated Water
In applications where the water quality cannot be held to
prescribed limits, the use of a secondary or intermediate
heat exchanger is recommended to separate the unit from
the contaminated water.
The following table outlines the water quality guidelines
for unit heat exchangers. If these conditions are exceeded,
a secondary heat exchanger is required. Failure to supply
a secondary heat exchanger where needed will result in a
warranty exclusion for primary heat exchanger corrosion
or failure.
Water Quality Guidelines

7
NSW INSTALLATION MANUAL
to-water heat exchanger (See Pressure Drop Table for water
flow and pressure drop information). Normally about 3 GPM
flow rate per ton of cooling capacity (2.25 GPM per ton
minimum) is needed. Both source as well as load fluid piping
must be at least as large as the unit connections on the heat
pump (larger on long runs).
Never use flexible hoses of a smaller inside diameter than
that of the water connection on the unit and limit hose length
to 10 ft. per connection. Check carefully for water leaks.
CAUTION: Water piping exposed to outside
temperature may be subject to freezing.
Open Loop Well Water Systems
Always maintain water pressure in the heat exchanger by
placing water control valves at the outlet of the unit. Use
a closed bladder type expansion tank to minimize mineral
deposits. Ensure proper water flow through the unit by
checking pressure drop across the heat exchanger and
comparing it to the figures in the pressure drop table.
Normally, about 2 GPM flow rate per ton of cooling capacity
is needed in open loop systems, (1.5 GPM per ton minimum if
entering source temperature is above 50°F [10°C].
Some water control valves draw their power directly from
the unit’s 24V transformer and can overload and possibly
burn out the transformer. Check total VA draw of the water
valve(s) and ensure it is under 40 VA.
Discharge water from a heat pump can be disposed of in
various ways depending on local building codes (i.e. recharge
well, storm sewer, drain field, adjacent stream or pond,
etc.). Most local codes restrict the use of sanitary sewer for
disposal. Consult your local building and zoning departments
to ensure compliance in your area.
General
Each unit is equipped with captive FPT water connections
to eliminate ‘egg-shaping’ from use of a backup wrench.
For making the water connections to the unit, a Teflon tape
thread sealant is recommended to minimize internal fouling
of the piping. Do not over tighten connections. All supply and
return water piping should be insulated to prevent excess
condensation from forming on the water lines.
NOTE: Units are factory run-tested using propylene
glycol. Prior to connecting piping to unit, thoroughly flush
heat exchangers.
The piping installation should provide service personnel with
the ability to measure water temperatures and pressures.
The water lines should be routed so as not to interfere with
access to the unit. The use of a short length of high pressure
hose with a swivel type fitting may simplify the connections
and prevent vibration. Optional stainless steel hose kits are
available as an accessory item.
Before final connection to the unit, the supply and return
hose kits must be connected, and the system flushed
to remove dirt, piping chips and other foreign material.
Normally, a combination balancing and close-off (ball) valve
is installed at the return, and a rated gate or ball valve is
installed at the supply. The return valve can be adjusted to
obtain the proper water flow. The valves allow the unit to be
removed for servicing.
The proper water flow must be delivered to each unit
whenever the unit heats or cools. To assure proper flow,
the use of pressure/temperature ports is recommended
to determine the flow rate. These ports should be located
adjacent to the supply and return connections on the unit.
The proper flow rate cannot be accurately set without
measuring the water pressure drop through the refrigerant-
Field Connected Water Piping
Line Voltage
Disconnect
Load Liquid
Connections
Water Out
Water In
Rubber Bladder
Expansion Tank
Solenoid
Valve
Flow Regulator Valve
Shut-off Valve
(to isolate solenoid
valve while acid
flushing)
Boiler Drains for
HX Flushing
Shut-off
Valve
Vibration Absorbing
Mesh or Air Pad
P/T Plugs
NOTE: Valves and boiler drains must be installed
so the heat exchanger can be acid flushed.
Typical Open Loop Installation

8
NSW INSTALLATION MANUAL
Field Connected Water Piping cont.
Earth Coupled Systems with Flow Center
Once piping is completed between the unit, flow center
and the earth loop, final purging and charging of the loop
is needed. A flush cart (at least a 1.5 HP or 1.12 kW pump)
is needed to achieve adequate flow velocity in the loop to
purge air and dirt particles from the loop itself. Antifreeze
solution is used in most areas to prevent freezing. Maintain
the pH in the 7.6-8.2 range for final charging.
Flush the system adequately to remove as much air as
possible. Then, pressurize the loop to a static pressure of
50-75 psi [345-517 kPa]. This is normally adequate for good
system operation. Ensure that the flow center provides
adequate flow through the unit by checking pressure drop
across the heat exchanger and by comparing it to the
figures shown in the Pressure Drop tables. Usually, 3 GPM/
ton [0.054 L/s/kW] L/s/kW or minimum 2.25 GPM/ton
[0.04 L/s/kW] of cooling capacity is needed in closed loop
earth-coupled applications
Typical Closed Loop Earth Coupled Installation
Line Voltage
Disconnect
Load Liquid
Connections
Vibration Absorbing
Mesh or Air Pad
P/T Plugs
Unit Connector Kits
with Insulation
Earth Coupled Loop
Piping with Insulation
Potable Water Systems
The NSW018 and NSW025 models can be equipped to
provide domestic hot water generation. An optional
factory-installed hot water generator coil may be provided
with the NSW040, NSW050, NSW060, and NSW075 to
assist with this process.
LOAD PUMP
HYDRONIC
LOAD
Source OUT
P/T PortsP/T Ports
Ball Valve
Dielectric
Unions
Dielectric
Unions
WaterFurnace
NSW Series
NOTES:
* A 30 psi pressure relief valve (Part No: SRV30) should be used in
hydronic applications.
** Vent valve or P/T port at highest point in return line prior to ball valve.
1-1/2 in.
FPT
Expansion
Tank
Air
Vent
Pressure
Gauge
30 psi
RELIEF VALVE
Air
Separator
FROM
HWG
TO
HWG
Back Flow Preventer /
Pressure Relief Valve
Source IN
GEO
STORAGE
TANK
PUMP
HOT
(Piped in
series to
an electric
water heater)
COLD
DOMESTIC
Dip Tube
Ball Valve
Vent Valve/
P/T Port**
Suggested Domestic Water Heater Hookup

9
NSW INSTALLATION MANUAL
NOTES:
1) Unions and valves must be installed so that acid flushing
of the heat exchanger is possible.
2) Route thermistor wires to NSW. Remove yellow
thermistor wires on TB 3 and 4 from control box and
connect thermistor wires from geothermal storage tank.
Set the pump sampling (PS) in the set up of the control
board to continuously (C) sampling (reference Note 5 in
the Wiring Schematic).
Hot Water Generator Connections
The heat reclaiming hot water generator coil is vented double-
wall copper construction and is suitable for potable water. To
maximize the benefits of the hot water generator a minimum
50-gallon water heater is recommended. For higher demand
applications, use an 80-gallon water heater as shown below or
two 50-gallon water heaters connected in a series. A geo storage
tank should not be used in this application unless it is plumbed
in a series with an electric water heater. The geo storage tank
is equipped with a single 4500 Watt element and will not be
able to provide adequate water heating if used as a standalone
water heater. Electric water heaters are recommended. Make
sure all local electrical and plumbing codes are met for installing
a hot water generator. The Envision NSW is not supplied with
an internal circulator. A DPK5 kit will need to be purchased to
connect to the hot water generator. The DPK5 kit is supplied with
installation instructions, circulator, tank adaptor and temperature
limit switch. Be sure to burp (vent) the pump. Open the screw
2 turns only in the end of the pump motor (if Grundfos®pumps
are used) to allow trapped air to be discharged and to ensure the
motor housing has been flooded.
Potable Water Systems cont.
Alternate Hot Water Installation with
Direct Coupling to a Double Wall Unit
>B>]`ba>B>]`ba
0OZZDOZdS
2WSZSQb`WQ
C\W]\a
2WSZSQb`WQ
C\W]\a
EObS`4c`\OQS
<AE&]`<AE #6SObW\U=\Zg
eWbV2]cPZSEOZZ:]OR1]Of
EObS`4c`\OQS
53=B/<9
 Þ
4>B
0OZZDOZdS
6=B 1=:2
:==>473:2
4:=E13<B3@
NOTES:
1) Unions and valves must be installed so that acid flushing
of the heat exchanger is possible.
2)
Make sure there is not a check valve in the diptube of
the tank.
3) Route thermistor wires to NSW. Remove yellow
thermistor wires on TB 3 and 4 from control box and
connect thermistor wires from geothermal storage tank.
Set the pump sampling (PS) in the set up of the control
board to continuously (C) sampling (reference Note 5 in
the Wiring Schematic).

10
NSW INSTALLATION MANUAL
Hydronic Section
General guidelines are shown below for component
selection and design/installation criteria for the piping
system. Local codes supersede any recommendations in
this manual.
Shut Off/Flow Regulation Valves
Use full port ball valves or gate valves for component
isolation. If valves are going to be used frequently, ball
valves are recommended. Globe valves are designed for flow
regulation. Always install globe valves in the correct direction
(fluid should enter through the lower body chamber).
Check valves
Swing check valves must be installed in the horizontal
position with the bonnet of the valve upright. Spring check
valves can be mounted in any position. A flow check valve
is required to prevent thermo-siphoning (or gravity flow)
when the circulator pump is off or when there are two
circulators on the same system.
Storage (Buffer) Tank
A buffer tank is required for all hydronic heating systems
using Envision NSW heat pumps. The tank should be sized
to provide 2 gallons of storage capacity for every one
thousand Btuh’s of nominal heat pump capacity.
Pressure Relief Valve
Most codes require the use of a pressure relief valve if a
closed loop heat source can be isolated by valves. Even
if local code does not require this device, WaterFurnace
recommends its installation. If the pressure relief valve in
the buffer tank is not already rated at 30 psi (207 kPa)
maximum pressure, one must be installed. The pressure
relief valve should be tested at start up for operation. Note
that the waste pipe must be at least the same diameter
as the valve outlet (never reduce), and valves may not be
added to this pipe. The bottom of the pipe must terminate
at least 6” (15 cm) above the floor. If the piping is connected
to a drain, there must be an air gap.
Backflow Prevention Check Valves
Most codes require backflow prevention check valves.
Note that a single check valve is not equal to a backflow
prevention check valve. Even if local code does not require
this device, WaterFurnace recommends its installation. This
is particularly important if the system will use antifreeze.
Pressure Reducing Valves or Feed Water Valves
This valve lowers the pressure from the make-up water line
to the system. Most are adjustable and directional. A “fast
fill” valve is required for initial filling of the system. Some
have screens, which must be cleaned after the initial filling.
If there is a restriction in the screen, the system could go to
0 psi (0 kPa), potentially causing pumps(s) failure. A valve
should be installed on each side of the pressure reducing
valve for servicing. Both valves should have tags reading
“Do not shut this valve under normal operation – service
valve only.”
Expansion Tanks
Expansion tanks are required on hydronic systems to help
absorb the pressure swings as the temperature in the
system fluctuates.
Elbows/Tees
Long radius elbows or two 45° elbows will lower pressure
drop. Standard tees have a greater restriction on the “T”
portion than tees designed with angled outlet ports.
Antifreeze
Antifreeze is required if any of the piping system is located
in areas subject to freezing.
Dielectric Unions
Dielectric unions are recommended whenever connecting
two dissimilar metals to one and other to prevent electro-
galvanic corrosion.
When using the various types of hydronic heat distribution
systems, the temperature limits of the geothermal system
must be a major consideration. In new construction, the
distribution system can easily be designed with the
temperature limits in mind. In retrofits, care must be
taken to address the operating temperature limits of the
existing distribution system. The maximum storage tank
temperature for the Envision NSW is 130°F (54.4°C). Typical
in floor radiant systems require much lower temperatures,
typically 100°-115°F, which is ideal for the Envision NSW.

11
NSW INSTALLATION MANUAL
Hydronic Section cont.
Synergy3D
Thermostat
Open the screw 2 turns only in the end of the pump motor
(if Grundfos
®
pumps are used) to allow trapped air to be
discharged and to ensure the motor housing has been flooded.
Route thermistor wires to NSW. Remove yellow thermistor
wires on TB 3 and 4 from control box and connect to red
thermistor wires from the top of the geothermal storage
tank. Set the pump sampling (PS) in the set up of the control
board to continuously (C) sampling (reference Note 5 in the
Wiring Schematic).
Adequate rate of flow (GPM) is very important to system
performance and long term reliability. Follow the guidelines
for recommended flow and pipe sizing in the NSW
recommendations table.
WaterFurnace Geothermal Storage Tank Thermostat
and Thermistor
Yellow Thermistor Wires Connected to TB (3 and 4) on
NSW Control Board
NSW
LOAD PUMP
HYDRONIC
LOAD
Source OUT
P/T PortsP/T Ports
Ball Valve
Dielectric
Unions
Dielectric
Unions
WaterFurnace
NSW Series
NOTES:
* A 30 psi pressure relief valve (Part No: SRV30) should be used in
hydronic applications.
** Vent valve or P/T port at highest point in return line prior to ball valve.
1-1/2 in.
FPT
Expansion
Tank
Air
Vent
Pressure
Gauge
30 psi
RELIEF VALVE
Air
Separator
FROM
HWG
TO
HWG
Back Flow Preventer /
Pressure Relief Valve
Source IN
GEO
STORAGE
TANK
PUMP
HOT
(Piped in
series to
an electric
water heater)
COLD
DOMESTIC
Dip Tube
Ball Valve
Vent Valve/
P/T Port**

12
NSW INSTALLATION MANUAL
Accessories and Options
Earth Loop Pump Kit (Field Installed)
A specially designed one or two-pump module provides all
liquid flow, fill and connection requirements for independent
single unit systems (230/60/1 only). The one-pump module
is capable of 20 feet of head at 16.0 GPM, while the two-
pump module is capable of 40 feet of head at 16.0 GPM.
Hot Water Generator (Factory Installed, NSW040,
NSW050, NSW060, and NSW075 Only)
An optional heat reclaiming hot water generator coil
constructed of vented double-wall copper construction
suitable for potable water is available. The coil is factory
mounted inside the unit. A DPK5 pump kit is required (field
installed), which includes a DHW tank connection and a
temperature limit pump shutoff.
Load-side Pump Kit (Field Installed)
Four (4) load pump kits are available to provide all liquid flow
requirements for independent single unit systems (230/60/1
only). WaterFurnace part number 24S516-10 (Grundfos
UPS15-42RU) is a composite body pump. EWPK2 (Grundfos
UP26-64BF) is a bronze body pump. Bronze or composite
body pumps should be used when water conditions exist that
are not compatible with cast iron or for applications such as
domestic water heating. WaterFurnace part number EWPK1
and EWPK3 come with a cast iron body pump (Grundfos
UP26-99F) that can be used for hydronic heating applications.
Calculate the system pressure drop then refer to the pump
curves to select the proper pump. All four of the WaterFurnace
pump kits can be used for hydronic heating applications as long
as they meet the flow requirements. If the flow requirements
are outside the pump curve, an alternate pump will need to be
obtained to maintain the necessary flow.
IntelliStart®
The optional IntelliStart single phase soft starter will reduce
the normal start current (LRA) by 60-70%. This allows the
heat pump to go off-grid. Using IntelliStart also provides a
substantial reduction in light flicker, reduces start-up noise,
and improves the compressor’s start behavior. IntelliStart is
available in a field retrofit kit (WaterFurnace part number
IS60RKL or IS60RKS) or as a factory installed option for all
Envision and Synergy3D units.
Water Connection Kits (Field Installed)
Water connection kits are available to facilitate loop side
and load side water connections.
• MA4FPT - Forged brass 1” MPT x 1” FPT square street
elbow with P/T plug for NSW018-NSW040 water
side connections
• MA5FPT - Forged brass 1.25” MPT x 1.25” FPT square
street elbow with P/T plug for NSW050-NSW075 water
side connections
• 2-HVAC-1x24 - 1 inch x 24 inch stainless steel braided
hose kit
• 2-HVAC-1 1/4x24 - 1 1⁄4 inch x 24 inch stainless steel
braided hose kit
NOTE: Never use piping smaller than 1 inch. Limit length of
pipe to 50 feet or less.
Type L Copper Tube
GPM 3/4 1 1-1/4 1-1/2 2
21.5
33.2
45.5 1.4
58.5 2.1
62.9 1.1
73.9 1.4
85.0 1.8
96.1 2.3 0.9
10 7.5 2.8 1.1
12 3.9 1.6
14 5.2 2.1
16 6.6 2.7
18 8.2 3.4
20 10.0 4.1 1.1
22 5.0 1.3
25 6.3 1.6
30 2.2
35 2.9
40 3.8
45 4.7
50 5.7
Type L Copper Pressure Loss
Ft of Hd per 100 ft
NOTE: Standard piping practice limits pressure drop to 4
feet of hd per 100 feet in 2 inch and larger pipe.
UP26-64BF and UP26-99F Single and Two Pump Curve
UPS15-42RU Three-Speed Pump Curve
0
10
20
30
40
50
60
70
0 5 10 15 20 25 30
Feet of Head
GPM
UP26-64BF & UP26-99F Single and Two Pump
UP26-99F (2 Pumps)
UP26-64BF (2 Pumps)
UP26-99F (1 Pump)
UP26-64BF (1 Pump)
0
2
4
6
8
10
12
14
16
0 2 4 6 8 10 12 14 16
Feet of Head
GPM
UPS15-42RU 3-Speed Pump
UPS15-42RU (High)
UPS15-42RU (Med)
UPS15-42RU (Low)

13
NSW INSTALLATION MANUAL
3
0
°
3
0
°
To Geo 59˝ Dip Tube
w/1˝ x 3˝ Nipple
Approx. 1˝
T & P
VALVE
From Geo
1˝ x 3˝ Nipple
PRIMARY ANODE
39˝ - 80 Gallon
42˝ - 119 Gallon
3/4˝ COLD INLET
52˝ DIP TUBE
3/4˝ HOT OUTLET
w/14˝ SECONDARY ANODE
HEIGHT
Optional “To Geo”
Connection Shipped with
1-1/2˝ Pipe Plug Installed
Element Location
Red Wire attached
to Thermistor or Thermostat
for Top Exit
Lower Sensor Thermistor (12P541-01)
to be used by Water to Water Units
Optional “From Geo” Connection
Shipped with 1-1/2˝ Pipe Plug Installed
DIAMETER
8˝
5-1/4˝
35-3/4˝
Lower Thermostat to be used
with Synergy units
DRAIN VALVE
MODEL
NUMBER
GALLON
CAPACITY
ELEMENT
WATTAGE
(240 VOLT)
NUMBER
OF
ELEMENTS
R
VALUE
DIMENSIONS IN INCHES APPROX.
SHIPPING
WEIGHT (lbs.)
HEIGHT DIAMETER
GEO-STORAGE-80 80 4500 1 16 63-1/4 24 204
GEO-STORAGE-120 119 4500 1 16 63-1/4 28 311
Accessories and Options cont.
Geo Storage Tank Dimensions

14
NSW INSTALLATION MANUAL
NSW Control Box
Load Pump Fuse Block
Transformer
Run Capacitor
(Single Phase Only)
Ground Lug
Load Pump Relay
Terminal Board
Power Block
Terminal Power Strip
Optional IntelliStart
Compressor Contactor
Power Block
IntelliStart Only
Source Pump Fuse Block
Source Pump Relay
Reversing Valve Relay
Electrical Data
NOTES: All fuses type “D” time delay (or HACR circuit breaker in USA).
Source pump amps shown are for up to a 1/2 HP pump.
Load pumps amps shown are for small circulators.
*LRA with optional IntelliStart installed (208-230/60/1).
Model Rated
Voltage
Voltage
Min/Max
Compressor Load
Pump
Source
Pump
Total Unit
FLA
Min Ckt
Amp
Maximum
Fuse/HACR
RLA LRA LRA*
018 208-230/60/1 187/253 9.0 48.0 17.0 1.8 5.4 16.2 18.5 30
025 208-230/60/1 187/253 13.5 61.0 21.4 1.8 5.4 20.7 24.1 35
040 208-230/60/1 187/253 20.0 115.0 40.3 1.8 5.4 27.2 32.2 50
050 208-230/60/1 187/253 26.4 134.0 46.9 1.8 5.4 33.6 40.2 60
060 208-230/60/1 187/253 30.1 145.0 50.8 1.8 5.4 37.3 44.8 70
075 208-230/60/1 187/253 26.9 145.0 50.8 1.8 5.4 34.1 40.8 60
7/26/13

15
NSW INSTALLATION MANUAL
Electrical Data cont.
208 Volt Operation
All 208-230 volt units are factory wired for 230 volt
operation. To convert the unit from a 230V unit to a 208V
unit follow these steps:
1. Remove the blue transformer wire from terminal L2 on
the compressor contactor and secure the wire taking
care to insulate the end with electrical tape.
2. Locate the red transformer wire and connect it to the L2
terminal of the compressor contactor.
Electrical
Be sure the available power is the same voltage and phase
as that shown on the unit serial plate. Line and low voltage
wiring must be done in accordance with local codes or the
National Electric Code, whichever is applicable. Refer to
the Electrical Data table for wire and fuse or circuit breaker
sizing information.
Flow Center Pump Connection (208-230/60/1)
Two fuse internal terminal block connections with 1/4-inch
spade connectors are provided; one for the load pump
and one for the source pump. The source pump directly
connects to the fuse terminal block for the source pump.
The load pump directly connects to the fuse terminal block
for the load pump.
NSW Control Box Relocation
The NSW control box can be installed on the rear of the unit.
To relocate the control box, follow the procedures below.
1. Remove all power sources to the unit.
2. Remove the unit’s top panel.
3. Cut all plastic wire ties to the following:
a) High pressure switch (black wires)
b) Low pressure switch (blue wires)
c) Freeze sensing (yellow wires)
d) Load temperature sensor (black wires)
e) Compressor wires
4. Remove the four screws from the control box.
5. Relocate the control box to opposite end of the unit.
6. Using the screws removed in step 4 above, reattach the
control box.
7. Secure all wires so they do not come in contact with
refrigerant lines.
8. Replace the top of the unit.
9. Replace both access panels.
10. Reapply power sources.
NOTE: If geothermal storage tank is used, connect yellow
thermistor wires from the bottom access panel of the tank
to spade connectors 3 and 4 on the terminal block.

16
NSW INSTALLATION MANUAL
Wiring Schematics
For all NSW 208/230 volt single-phase units, the circulator
wiring is as shown in the illustrations below. The internal
relay and fusing allow for external pumps no larger than .5
horsepower. The external loop pump connections mentioned
in this manual include a dedicated flow center for each unit
as well as an NSW unit connected to an Envision; “P” or an
“E” series unit containing a microprocessor.
CONTROL BOX
LOAD
CIRCULATOR
PUMP
TRANSFORMER
LOW VOLTAGE
TERMINAL STRIP
FUSE
BLOCKS
LOW VOLTAGE
THERMOSTAT
CONNECTIONS
COMPRESSOR
CONTACTOR
T1 T2
L1 L2
CAPACITOR
TRANSFORMER
LOW VOLTAGE
TERMINAL STRIP
FUSE
BLOCKS
LOW VOLTAGE
THERMOSTAT
CONNECTIONS
FLOW CENTER
CONTROL BOX
COMPRESSOR
CONTACTOR
T1 T2
L1 L2
CAPACITOR
Load Circulator Wiring
Dedicated Flow Center Wiring

17
NSW INSTALLATION MANUAL
Wiring Schematics cont.
TRANSFORMER
LOW VOLTAGE
TERMINAL STRIP
FUSE
BLOCKS
LOW VOLTAGE
THERMOSTAT
CONNECTIONS
P2
SHUT
DOWN
C
Not
Used
C
P1
G
W
O
R
C
Y1
Y2
LO
CONTROL
BOX
13P003B RELAY
(FIELD SUPPLIED)
SL1 IN
SL1OUT
CONTROL BOX
COMPRESSOR
CONTACTOR
T1 T2
L1 L2
CAPACITOR
Multiple Units on a Single Flow Center Wiring

18
NSW INSTALLATION MANUAL
Wiring Schematics - Residential
NSW Heating Only - 208-230/60/1
Transformer
NOTE1
Red
208V
Black
Com
Compressor
Unit
Power Supply
CC
T1
L1
T2
Tan
Brown
Blue
G
C
R
S
BlackRed
Blue
Factory low voltage wiring
Legend
Switch- High pressure
Switch- Low pressure
Relay coil
Field wire lug
Ground
Relay Contacts -
N.O., N.C.
Polarized connector
Notes:
Factory line voltage wiring
Field low voltage wiring
Field line voltage wiring
Optional block
Quick connect terminal
Screw terminal - field connection
CC -
-
HP -
LP -
LPR -
Compressor contactor
High pressure switch
Low pressure switch
Load Pump Relay
L1
1 3 2
PCapacitor
24V
Microprocessor Control
TEST
PIN
HP HP CC CG HI LO CLP LPR HP HP CC CG HI LO CLP LPR
CC
HP
LP
Black/
White
Blk/Wht
Violet
Black
Black
White/Blue
White/Blue
Red
LPR
T
T
RT
ELT
Orange
X1ELTELTRTRT
X2 X1
X1ELTELTRTRT
X2X1
RV Reversing Valve output
ELT -Entering Load Side Water Temperature
Green/Yellow
TThermistor
P1
P2
P3
X3
X3
X3
X3
LPR
Interface Panel
Black
Black
Yellow
Yellow
Violet
Violet
Orange
Orange
Gray
Gray
1
2
3
4
5
6
7
8
TB
1
1
G
Load
Pump
External
X2
X2
PS1
RV RVG
RT -Refrigerant Liquid line Temperature
SI
SI -Slave Input relay
RCY1 OX1
G
External
SI
RC -Reversing Valve Coil
Fuse
Cap
9
10
11
12
1. Taped and wire tied off
Not Used
Not Used
Not Used
Not Used
Not Used
Green/Yellow
Yellow
24V
BCD
L2 L2L1L1
T1T1 T2T2
LFB SFB
LFB -
SFB - Load Pump Fuse Block Source Pump Fuse Block
NOTE2
2. 3AG10 Amp fuse
Blue/Wht
Brown/Wht
Brown/Blk
Red
Black
Orange
Black/Gry
Violet
Black/Wht
L2
208-230/60/1
Source
Pump
MODE
3. For cycle load pump with a geo storage
tank. Remove the orange wire from the LPR
relay coil and install a jumper between the
LPR relay coil and the comp contactor coil
as shown in the schematic above.
Note 3
Blue
230V
04/02/09

19
NSW INSTALLATION MANUAL
Wiring Schematics - Residential cont.
NSW Reversible with IntelliStart - 208-230/60/1
Transformer
NOTE1
Red
208V
Compressor
Unit
Power Supply
CC
T1
L1
T2
Brown
G
C
R
S
Blue
24V
Microprocessor Control
TEST
PIN
HP HP CC CG HI LO CLP LPR
CC CG HI LO CLP LPR
HP
LP
Black/
White
Blk/Wht
Violet
White/Blue
White/Blue
LPR
T
RT
Orange
X1 EL
TELTRTRT
X2X1
X1 ELTELTRTRT
X2 X1
Green/Yellow
P1
P2
P3
X3
X3
X3
X3
LPR
Interface Panel
Black
Black
Yellow
Violet
Violet
Orange
Orange
Gray
Gray
1
2
3
4
5
6
7
8
TB
1
1
G
Load
Pump
External
X2
X2
PS1
RV RVG
SIR
RCY1 OX1
G
External
SI
Cap
9
10
11
12
Not Used
Not Used
Not Used
Green/Yellow
Yellow
24V
BCD
L2 L2L1L1
T1T1 T2T2
LFB SFB
NOTE2
Brown/Wht
Brown/Blk
Red
Black
Orange
Black/Gry
Black/Wht
L2
208-230/60/1
Source
Pump
MODE
RVR
RVR
T
RT
Yellow
RC
NOTE 3
RVR
T
ELT
Org/Wht Org/Blk
Blue Blue
Black Black
Yellow
Yellow
Violet
Black/Org
Org/Gry
Org/Brn
HP HP
Black
Black
Red
Org/Grn Orange
NOTE 4
Note 5
CC
Black
Com
Blue/Wht
Blue
Blue
230V
Black
Tan
Black
Run Winding
Active
Start
Common
IntelliStart
Pink
Black
2
1
PB
RedRed
Blue
Factory low voltage wiring
Legend
Switch- High pressure
Switch- Low pressure
Relay coil
Field wire lug
Ground
Relay Contacts-
N.O., N.C.
Polarized connector
Notes:
Factory line voltage wiring
Field low voltage wiring
Field line voltage wiring
Optional block
Quick connect terminal
Screw terminal - field connection
Compressor Contactor
High Pressure Switch
Low Pressure Switch
Load Pump Relay Contacts
L1
1 3 2
PCapacitor
Reversing Valve Output
Entering Load Side Water Temperature
TThermistor
Refrigerant Liquid Line Temperature
Slave Input Relay
Reversing Valve Coil
Fuse
1. Taped and wire tied off
Load Pump Fuse Block
Source Pump Fuse Block
2. 3AG 10Amp fuse
3. Move jumper wire to 5 and 6 for reversible
secondary unit.
4. Black Thermistor - Source Coax Blue
Thermistor - Load Coax
5. For cycle load pump with a geo storage tank.
Remove the orange wire from the LPR relay coil
and install a jumper between the LPR relay coil
and the comp contactor coil as shown in the
schematic above.
CC -
-
HP -
LP -
LPR -
RV
ELT -
RT -
SIR -
RC -
LFB -
SFB -
RVR -Reversing Valve Relay
04/02/09

20
NSW INSTALLATION MANUAL
Y1 = Compressor call
R = 24VAC
C
G
W1
L
X1
Y2
O
Y1
W2
S
X2
R
Control Box
Typical Aquastat
Secondary Unit
(SL=1)
Aquastat Wiring for Dedicated Heating or Cooling Unit
Y1 = Compressor call
O = Reversing valve call
R = 24VAC
Note: Jumper wire must be
moved to terminals 5 & 6.
Secondary Unit
(SL=1)
C
G
W1
L
X1
Y2
O
Y1
W2
S
X2
R
Typical Aquastat
1
2
3
4
5
6
7
8
9
10
11
12
Jumper
Wire
Control Box
Aquastat Wiring for Reversible Unit
External Control
Primary Mode
In dedicated heating or cooling units, the unit is controlled
by the internal controller. Compressor output is determined
by the entering load-side water temperature.
The secondary output will be energized if two
conditions occur:
1. The initial temperature is greater than IC away from the
set point.
2. The change in temperature in a given period of time Pis
less than d.
In a reversible unit, the unit is controlled by the internal
controller. Compressor output is determined by the
entering load-side water temperature. For reversible units,
the jumper wire must be positioned across terminals 6 and
7, (factory default set to this position). Reversible units do
not have a secondary output.
NOTES: SL in the configuration menu must be set to 0,
(factory default). All parameters should be checked for each
application on primary unit, (refer to the parameter table).
Secondary Mode
In dedicated heating or cooling units, secondary mode
allows the unit to be controlled by an external source.
Compressor output is determined by the Y1 input only.
The secondary output will be energized after the following
condition occurs:
1. The change in temperature in a given period of time Pis
less than d.
In reversible units, secondary mode allows the unit to
be controlled by an external source. Compressor output
is determined by the Y1 input and the reversing valve
is determined by the O input. In reversible units, the
jumper wire must be positioned across terminals 5 and 6.
Reversible units do not have a secondary input.
NOTES: SL in the configuration menu must be set to 1. P
and dmust be setup for each secondary unit.
Wiring an Aquastat - Reversible Unit
• To create a secondary unit, set SL to 1 in the
configuration menu.
• Position the jumper wire in the control box across
terminals 5 and 6.
WARNING: Reversible units cannot be
staged.