Watersports Innovations The Boost Box WS 1107 Installation instructions

AUTOMATIC VOLUME CONTROL
FOR BOAT STEREOS
WS 1107 Wired Controller for MB Quart Marine Stereos
Installation
& Operation
Instructions

Contents
i
Chapter 1 Installation Instructions............................................1
Control Unit .............................................................2
Power Cable ............................................................4
Stereo Control Cable...............................................5
Chapter 2 Using the Boost Box ................................................6
Chapter 3 Troubleshooting Guide............................................8
Chapter 4 Release of Liability...................................................9
Warranty ................................................................10

1
Installation Instructions
1
Read through all instructions before installing. The Boost
Box is designed to install easily on almost any boat with little
or no wiring modifications. Simply attach the Control Unit to
the boat with the enclosed Velcro tape, connect the Power
Cable to the boat’s 12-volt power, and route the Stereo
Control Cable to the back of the boat’s stereo.
To prevent electric shock hazard, disconnect the boat
battery prior to installation.

2Chapter 1 Installation Instructions
Step 1 – Control Unit Installation
The Control Unit must be mounted with the control knob
facing the driver, and the unit must be mounted within 10°
of level with respect to the boat’s waterline. The unit can
be mounted either horizontal or vertical (see figures below).
Attach the Control Unit to the boat with the enclosed Velcro
tape, in a convenient location near the driver.
3CORRECT horizontal mounting. Knob is facing the driver, unit is
parallel to the floor of the boat, and the centerline of the Control
Unit is parallel with the centerline of the boat (bow to stern).
3CORRECT verticle mounting. Knob is facing the driver, and the
centerline of the Control Unit is parallel with the boat’s waterline.
3
3

3
Chapter 1 Installation Instructions
NOTE: If the unit is not mounted properly, it will not
properly sense the boat’s acceleration. Below are some
examples of INCORRECT mounting of the Control Unit.
INCORRECT! Knob is facing up but should be facing the driver.
Centerline (front to back) of the Control Unit is perpendicular, but
should be parallel, to the boat’s waterline.
INCORRECT! Knob is facing the driver, but Control Unit is not
parallel with the boat’s waterline, and the Control Unit is not parallel
with the boat’s center axis (bow to stern).

4Chapter 1 Installation Instructions
Step 2 – Power Cable Installation
The Power Cable plugs into the back of the Control Unit, as
shown below, and the free end is wired into the boat’s 12-volt
power. Connect the red wire to power and the black wire to
ground. Connect the Power Cable to a circuit protected by
a fuse rated at 10 amps or less that is powered only when
the boat’s ignition switch is in the “ON” or “ACCESSORY”
position.
An alternate cigarette lighter adapter is available if wiring
directly to the boat is not desired. Unplug the cigarette
lighter for extended storage, as the Boost Box continues to
draw a very slight current even when turned off. To order
these adapters, visit the Watersport Innovations website at
www.watersportinnovations.com.
CAUTION: The Boost Box must be connected to a
circuit protected by a circuit breaker or fuse rated at 10
amps or less. Do not wire directly to the battery. The
Control Unit is protected by a self-healing fuse and will
restart after cooling down in the event of short-circuit.
The external power cable wiring is not protected by the
Control Unit fuse and may overheat or cause a fire in
the event of short-circuit, unless properly protected by
a fuse or circuit breaker.
REAR SIDE OF UNIT
Remote Transmitter Cable plug Power Cable plug

5
Chapter 1 Installation Instructions
Step 3 – Stereo Control Cable Installation
The Stereo Control Cable plugs into the back of the Control
Unit, and into the back of the MB Quart stereo head unit.
Both ends of the cable are male 3.5mm jacks and the ends of
the cable are labeled. The proper ends must be connected
to the Control Unit and the stereo. The Boost Box will not
function if the Control Cable is reversed.
If there are additional MB Quart remotes (not included) to
be connected to the 3.5mm jack on the rear of the stereo
head unit, then use the optional Y adapter. Plug the Boost
Box and the MB Quart remotes into the female ends of the
Y adapter, and plug the male end of the Y adapter into the
stereo head unit. (See figure on page 1)
IMPORTANT NOTE: The Stereo Control Cable end
labeled “Boost Box” MUST be plugged into the back
of the Boost Box Control Unit. If the optional Y adapter
is used, the end of the Stereo Control Cable labeled
“Stereo” must be plugged into the Y adapter.

2
Using The Boost Box
6
The Boost Box is designed to adjust the stereo volume when
pulling riders. When installed properly, the device sends
remote control commands to the boat’s stereo. The Boost
Box automatically increases stereo volume when it senses
six seconds of continuous acceleration, and automatically
decreases volume when the boat slows to pick up a fallen
rider.
NORMAL OPERATION: The driver can select the amount of
the rise in volume by adjusting the selector knob on the front
of the Control Unit. To increase the amount of volume boost,
turn the knob clockwise. To decrease the amount of volume
boost, turn the knob counter-clockwise. Maximum volume
boost is indicated on the control face (Max Boost).
CAUTION: The Boost Box can produce major changes
in stereo volume. Do not set the control unit selector
knob to a position past the mid-point until the unit
has been tested in conjunction with the boat’s stereo.
Undesirable or damaging volume levels may occur!
Some stereo brands may require operation at higher
levels.
The red LED on the front of the Control Unit will illuminate
when the unit is on and functioning. The LED will flicker when
the Boost Box is changing the stereo volume (increasing or
decreasing).
To turn the unit off, simply turn the volume control knob to
the off position. The LED will turn off and the unit will enter
a power-saving mode. The boat’s stereo will continue to
function normally.
CONTROL UNIT
PROOF FOR APPROVAL
GF020 REV 003
PAGE 1 OF 1
Proof # 3
Date: 11-10-08
Customer Part #: The Boost Box label
LASI Item #: SS3578-001 art rev 001
Part Size: 4.27˝ x 1.16˝
Ink Color: Black, White
SYSTEMS, INC.
P.O. Box 550 104 Celtic Circle Madison, Alabama 35758
I have thoroughly reviewed the proof for accuracy in copy, color layout, and size. I understand that I am responsible for the accuracy
of all information contained in this proof.
Signature Date
The proof meets my approval. Please proceed with my order. Make the changes indicated on the proof and re-proof.
Material: 10 mil Velvet Lexan w/PermanentAdhesive
left side
of copy
dispenses
first
4.
top of
copy
dispenses
first
1.
bottom of
copy
dispenses
first
2.
right side
of copy
dispenses
first
3.
top of
copy
dispenses
first
5.
bottom of
copy
dispenses
first
6.
left side
of copy
dispenses
first
8.
right side
of copy
dispenses
first
7.
Automatic Volume Control
Off Max Boost

7
Chapter 2 Using The Boost Box
CALIBRATION: The Control Unit automatically calibrates
(resets) its internal sensors every time it is turned on. This
precisely calibrates the sensors to the boat’s level position
in the water.
To calibrate the Boost Box:
1. Ensure the boat is in flat water with no rolling waves.
2. Turn the unit on and ensure the LED is steadily
illuminated for 2 seconds.
3. Rotate the selector knob all the way to the off position
(LED should go out) and then rotate clockwise until
the LED begins to flash.
4. The LED will flash slowly, then more quickly. When
the LED is steadily illuminated, the Control Unit is
successfully calibrated.
The Control Unit has an internal memory circuit and will
remain calibrated when the boat power is switched off or if
the unit is unplugged. The unit will re-calibrate only when
the selector knob is rotated off and then turned back on.
IMPORTANT NOTE: For best performance, re-calibrate
the unit after adding or removing significant amounts of
ballast from the boat, as this may change the way the
boat sits in the water.
Do not turn the Boost Box on when the boat is moving or
is in rough water. The Control Unit will improperly reset its
calibration, and the system will not function properly.

3
Troubleshooting Guide
8
Below are some possible conditions and solutions.
CONDITION SOLUTION
Unit will not turn on.
Unit turns on, but
boat volume does not
change when boat
pulls a rider and LED
does not flash.
LED flashes when
boat pulls a rider, but
stereo volume does
not increase.
Volume is slow to
return to normal
volume when boat
slows down.
Boat stereo volume is
increased when boat
is not pulling a rider.
NOTe: The Boost Box is intended for use controlling the boat
stereo when pulling waterskiers, wakeboarders, or wakesurfers.
Because the Boost Box works by sensing the boat’s acceleration
and deceleration, it may turn down inadvertently if used during
aggressive deceleration when towing tube riders. This is normal
and is a limitation of the system.
If you are still having trouble with your Boost Box, please call
Watersport Innovations technical support at [phone]
or send an email to: [email protected]
Check to ensure Power Cable is firmly
plugged into Control Unit. Ensure power
cable is properly wired to battery’s 12-
volt DC power.
The Control Unit is not sensing the
boat’s acceleration. It is either mounted
improperly (see pages 2-3, Installation)
or needs to be re-calibrated. To re-
calibrate, wait until the boat is in
relatively flat water (no rolling waves)
and turn the unit off and back on.
Ensure Stereo Control Cable is installed
correctly. Check the connection to the
Control Unit, and ensure the male end of
the Control Cable is firmly plugged into
the stereo.
Unit may need to be re-calibrated. Turn
the unit off and back on. This should be
necessary only if the unit was turned on in
rough water or if the boat’s load changes
significantly (loading fat-sacks, etc.).
Unit may need to be re-calibrated. Turn
the unit off and back on. This should be
necessary only if the unit was turned on in
rough water or if the boat’s load changes
significantly (loading fat-sacks, etc.).

4
Release of Liability
ASSUMPTION OF RISK
9
IMPORTANT – YOU MUST READ THIS
The Boost Box is a high performance mechanism designed solely for use
with water ski and wakeboard boats operating under ideal, calm conditions
utilizing a spotter and all other safety crew and requirements of tournament
water skiing. The Boost Box should not be used for any other purpose or
under any other conditions.
YOUR USE OF YOUR BOOST BOX AUTOMATIC VOLUME CONTROLLER
IS CONDITIONAL UPON YOUR ASSUMING ALL RISKS, LOSSES AND
DANGERS RELATING TO USE OF THIS DEVICE.
Both purchaser and/or anyone utilizing the Boost Box acknowledges that
their purchase and/or use of this device is conditional upon purchasers
and users releasing and forever discharging Watersport Innovations, Inc.,
its directors, officers, employees, agents and/or dealers from any and all
liability for personal injury or property loss and from any other claims,
demands, losses or causes of action, whether occurring prior to, during,
or subsequent to or directly or indirectly connected with the use of the
Boost Box device and whether caused by any persons negligence or
otherwise.
The purchaser hereby agrees to inform any subsequent purchasers or
anyone using the Boost Box of the conditions of this Release of Liability -
Assumption of Risk agreement. It is agreed that there shall be absolutely no
alterations to this agreement whether by implication or otherwise.
CAUTION: The Boost Box must be connected to a
circuit protected by a circuit breaker or fuse rated at 10
amps or less. Do not wire directly to the battery. The
Control Unit is protected by a self-healing fuse and will
restart after cooling down in the event of short-circuit.
The external Power Cable wiring is not protected by the
Control Unit fuse and may overheat or cause a fire in
the event of short-circuit, unless properly protected by
a fuse or circuit breaker.
CAUTION: The Boost Box can produce major changes
in stereo volume. Do not set the Control Unit selector
knob to a position past the mid-point until the unit
has been tested in conjunction with the boat’s stereo.
Undesirable or damaging volume levels may occur!
Some stereo brands may require operation at higher
levels.

LIMITED WARRANTY
During the first 12 months from date of original retail purchase,
any Boost Box component that fails due to defects in materials
or workmanship will be repaired or replaced at the option of
Watersport Innovations at no charge.
Warranty excludes components damaged by improper
installation or improper use of boat. The Control Unit is water
resistant, but not waterproof and should never be submerged.
Please include a copy of the original sales receipt with any
warranty claim.
Warranty Service:
1. If your Boost Box was installed by the factory,
any warranty issues should be addressed to your
manufacturer’s authorized service center.
2. If your Boost Box was installed by a dealer, you may
contact your dealer directly or initiate a warranty claim
directly with Watersport Innovations at your choice.
3. If you purchased your Boost Box directly from the
Company, contact us at the number or address
below.
Warranty Service / Technical Support
WATERSPORT INNOVATIONS
P.O. Box 772
LaFollette, TN 37766
[phone]
[email protected]
enjoy the ride!