Waterworks PTWO04 Instruction sheet

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
.25
Push-Touch Waste and Overflow Installation Guidelines
Page 1 of 3
Rev
- 02
9.18.2015
These guidelines have been prepared for the professional contractor to aid in the installation of:
.25 PUSH-TOUCH WASTE AND OVERFLOW (STYLE No.PTWO04), .25 FREESTANDING OVAL BATHTUB (STYLE
No. PTBT25), .25 REVERSE FREESTANDING OVAL BATHTUB (STYLE No. PTBT52), & COLETTE FREESTANDING
OVAL BATHTUB (STYLE No. CBBT01).
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
STYLE No. PTWO04
Code No. WWDR04
RECOMMENDED FOR TUB(S):
PTBT25: .25 Freestanding Oval Bathtub
PTBT52: .25 Reverse Freestanding Oval Bathtub
CBBT01: Colette Freestanding Oval Bathtub
IMPORTANT:
Immediately after receiving the bathtub and removal of
packing, you MUST inspect the unit for freight damage.
Any claims for damage, whether apparent or hidden,
must be made to the carrier immediately in order for
them to assume all associated costs. Should inspection
reveal any defect in the finish, do not install the bath tub.
Damage or defect to the finish claimed after the bathtub
is installed is excluded from the warranty. The warranty
DOES NOT cover labor or materials to remove or reinstall
the bathtub.
To ensure this product is installed properly, you must
read and follow these guidelines.
The owner/user of the bathtub must keep this
information for future reference.
All final connections are made below the finished floor.
Accessibility below the finished floor is recommended.
For installations that have access from below the
finished floor, trap adapters can be used instead of the
slip joint gasket supplied.
For installations where access from below the finished
floor is limited, i.e. slabs, the slip joint gasket supplied is
required.
This product must be installed by a professional
licensed contractor. Be sure your installation conforms
to all federal, state, and local codes.
Refer to the specification and assembly drawings
attached.
Inspect this product to assure it is the correct model
and you have all parts required for proper installation.
Take all necessary precautions to ensure the tub is
protected during installation.
WASTE AND OVERFLOW ROUGH-IN NOTE:
A. This drain fits a tub that has an internal overflow
channel built INSIDE the wall of the tub which is
similar in design and function as a lavatory sink. There
is not a drain shoe that is common on standard tub
drains.
B. This drain does not use a cable or trip lever system to
operate the drain stopper. Instead, it uses a simple
pop-up drain that is closed and opened by pushing
down on the stopper.
1. Clean the drain hole area in the bathtub in preparation
of setting the drain. The area should be dry and free
of any debris and oil.
2. Cover the floor with a pad or other protective material
and gently rest the tub on its side to allow for drain
and overflow assembly.
3. Dry fit the drain assembly.
a. Place the drain collar (6) into the drain opening.
b. Slide the lower gasket (8) and metal washer (8a)
onto the drain collar, thread on the locking nut (9)
then attach the tail piece (10-12).
4. Determine the placement of the tub then mark the
floor at the center point of the drain opening.
5. Drill a hole through the floor to accommodate the
drain.
6. Rough in 1-1/2" DWV (not supplied). Assure all DWV
pipe and fittings are well supported to eliminate the
possibility of shifting.
7. IMPORTANT:Make sure the 1-1/2" hub is 1" - 3" to the
finished floor so the 5-3/4” tailpiece can be installed
securely. The slip joint gasket does not fit in a copper
coupling.
INSTALLATIONS THAT HAVE ACCESS FROM BELOW
THE FINISHED FLOOR:
WASTE AND OVERFLOW INSTALLATION
NOTE: Installations that have access from below the
finished floor, trap adapters can be used instead of the
slip joint gasket supplied.
8. Cover the floor with a pad or other protective material
and gently rest the tub on its side to allow for final
drain and overflow assembly.
9. Unthread the stopper (5, 5a & 5b) from the drain
collar then slide the rubber gasket (7) onto the collar
then insert it into the drain opening. A bead of clear
adhesive silicone around the drain collar can be
applied instead of the rubber washer.

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
.25
Push-Touch Waste and Overflow Installation Guidelines
Page 2 of 3
Rev
- 02
9.18.2015
These guidelines have been prepared for the professional contractor to aid in the installation of:
.25 PUSH-TOUCH WASTE AND OVERFLOW (STYLE No.PTWO04), .25 FREESTANDING OVAL BATHTUB (STYLE
No. PTBT25), .25 REVERSE FREESTANDING OVAL BATHTUB (STYLE No. PTBT52), & COLETTE FREESTANDING
OVAL BATHTUB (STYLE No. CBBT01).
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
10. Apply a generous bead of silicone to the drain collar
flange. Apply thread sealant on drain collar threads
and bottom of tub. Secure the collar using the gasket
(8), metal washer (8a), and locking nut (9) provided.
Make sure the gasket is positioned so its flat side
contacts the underside of the tub then the lock nut.
11. Insert the overflow assembly (1-3) into the overflow
hole.
12. Tighten the screw (3) to secure the overflow assembly
then thread the cover (4) onto the screw. Adjust the
screw as needed so the Waterworks logo is horizontal.
13. With the drain attached, position the tub so the drain
passes through the hole in the floor.
WASTE AND OVERFLOW CONNECTIONS (BELOW THE
FLOOR)
14. Install the tailpiece (11) using the tailpiece nylon washer
(10) and nut (12) provided. DO NOT over tighten.
15. Dry fit the remaining DWV pipe connections to the
proper dimensions. Using the 1-1/2" slip joint gasket
(13) provided, connect the tailpiece to the hub.
16. Go to step #24.
INSTALLATIONS WHERE ACCESS FROM BELOW THE
FINISHED FLOOR IS LIMITED, I.E. SLABS:
WASTE AND OVERFLOW INSTALLATION
17. Cover the floor with a pad or other protective material
and gently rest the tub on its side to allow for final
drain and overflow assembly.
18. Unthread the stopper (5, 5a, & 5b) from the drain collar
then slide the rubber gasket (7) onto the collar then
insert it into the drain opening.
19. Apply a generous bead of silicone to the drain collar
flange. Apply thread sealant on drain collar threads
and bottom of tub. Secure the collar using the gasket
(8), metal washer (8a), and locking nut (9) provided.
Make sure the gasket is positioned so its flat side
contacts the underside of the tub then tighten the lock
nut.
20. Insert the overflow assembly (1-3) into the overflow
hole.
21. Tighten the screw (3) to secure the overflow assembly
then thread the cover (4) onto the screw. Adjust the
screw as needed so the Waterworks logo is horizontal.
22.Install the tailpiece (11) using the nylon washer (10) and
nut (12) provided. DO NOT over tighten.
23.Dry-fit the slip joint gasket into the 1-1/2" hub then
measure the distance from the finished floor to the slip
joint gasket to make sure the tailpiece will fully insert
into the slip joint gasket. Cut the tailpiece as needed
and remove the slip joint gasket.
WASTE AND OVERFLOW CONNECTIONS (BELOW THE
FLOOR)
24. Apply clear adhesive silicone to the outside of the slip
joint gasket then insert it into the 1-1/2" hub (drain)
then apply clear adhesive silicone to the inside of the
slip joint gasket. Note the silicone will act as a
lubricant then act as a seal when it cures.
25.With the drain and tailpiece attached, position the tub
so the tailpiece passes through the hole in the floor
and slides into the 1-1/2" drain hub.
FINAL INSPECTION:
26.Fill the tub with water to the point where water
enters the overflow opening. Drain the tub while
inspecting all connections above and below the
flooring for leaks.
27.Run a bead of tub and tile caulk around the bottom
edge of the tub where it meets the floor. Wipe away
any excess caulk with a wet paper towel.
28.Cover the bathtub surface with a bathtub liner or
other form of protection until construction is
completed.
If further assistance is required, please contact
Product Support at 1-800-927-2120 Monday through
Friday, 8am - 6pm EST.
WARNING: The following basic safety precautions should
always be followed when using your bathtub.
Caution should always be exercised when entering or
leaving the bathtub.
DANGER: To reduce the risk of injury, do not permit
children or persons with a disability to use the
bathtub without close supervision.
Keep all electrical appliances such as radios and
hairdryers a safe distance from the bathtub.
Do not use the bathtub when sleepy or drowsy, under
the influence of alcohol or prescription medications or
when overheated.

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
.25
Push-Touch Waste and Overflow Installation Guidelines
Page 3 of 3
Rev
- 02
9.18.2015
These guidelines have been prepared for the professional contractor to aid in the installation of:
.25 PUSH-TOUCH WASTE AND OVERFLOW (STYLE No.PTWO04), .25 FREESTANDING OVAL BATHTUB (STYLE
No. PTBT25), .25 REVERSE FREESTANDING OVAL BATHTUB (STYLE No. PTBT52), & COLETTE FREESTANDING
OVAL BATHTUB (STYLE No. CBBT01).
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.