Waterworks Henry HNKM70 Instruction sheet

STYLE No. HNKM70, HN70KM
Henry One Hole Gooseneck Kitchen Faucet
with Pull-Down Spray and Metal Lever Handle
INSTALLATION GUIDELINES
PAGE 1 OF 6 | UPDATED ON 5.9.2018
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
IMPORTANT:
To ensure this product is installed properly, you must read and
follow these guidelines.
The owner/user of this product must keep this information for
future reference.
This product must be installed by a professional licensed
contractor.
Be sure your installation conforms to federal state, and local
codes. In the State of Massachusetts, all installations must comply
with the rules and regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts required for
proper installation. Product is sold partially assembled but shown
fully disassembled for illustrative and service purposed only.
Use only a strap wrench or protected/smooth-jaw wrench on any
finished surface.
The use of certain plumber’s putty may stain stone or tile surfaces.
If further assistance is required, please contact Product Support at
1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for available
replacement parts.
TECHNICAL DETAILS:
DETAIL SPECIFICATION
ADJUSTABLE VERSUS FIXED SPRAY ADJUSTABLE
HANDLE TURN ANGLE QUARTER TURN
INLET CONNECTION 3/8” COMPRESSION CONNECTOR HOSES †
RESTRICTED MAXIMUM FLOW RATE 2.2gpm [8.3L/min]
SPOUT REACH 7-9/16” [193mm]
SPOUT SWIVEL YES
SPRAY HOSE LENGTH 49” [1.2m]
SPRAY INCLUDED IN UNIT YES
WATER PRESSURE RANGE 20psi [1.5 bar] MIN
85psi [6.0 bar] MAX
WATER PRESSURE RECOMMENDED 45psi [3.0 bar]
†UK Style No., HN70KM is supplied with 2 BSPP adapters, assembly required.
MOUNTING
SURFACE
Ø 1-3/8"
[35mm]
FITTINGS
HOLE
1/4" MIN
[6mm]
3-1/4" MAX
[83mm]
DECK
THICKNESS

STYLE No. HNKM70, HN70KM
Henry One Hole Gooseneck Kitchen Faucet
with Pull-Down Spray and Metal Lever Handle
PAGE
2 OF 6 | UPDATED ON 5.9.2018
PRODUCT SUPPORT | 800.927.2120
| WATERWORKS.COM
INSTALLATION GUIDELINES
RUBBER WASHER
[DO NOT REMOVE]
THREADED ROD
[DO NOT REMOVE]
MOUNTING
BRACKET
METAL WASHER
BARREL NUT
[M8 THREAD]
1. Unthread and remove the BARREL NUT from the
THREADED ROD, then remove the METAL WASHER and
MOUNTING BRACKET.
NOTE: Do NOT remove THREADED ROD or RUBBER
WASHER beneath the ESCUTCHEON.
SPOUT
SUPPLY TUBE
[RED LABEL]
SUPPLY TUBE
[BLUE LABEL]
SUPPLY HOSE
SUPPLY HOSE
SUPPLY HOSE
MOUNTING
SURFACE
SPRAY
SUPPLY HOSE
RUBBER WASHER
ESCUTCHEON †
HANDLE ‡
[RIGHT SIDE
ONLY]
SPOUT
‡ RIGHT HAND HANDLE
INSTALLATION ONLY
† A RUBBER WASHER for the
ESCUTCHEON is provided.
If desired, a bead of caulk or clear
silicone may be applied where the
ESCUTCHEON contacts the
mounting surface.
2. Thread and securely tighten the SUPPLY HOSES onto the
SUPPLY TUBES installed on the SPOUT.
NOTE: The HOSES are M10 x 3/8” COMPRESSION
CONNECTOR HOSES and the SUPPLY TUBES are marked
BLUE for cold and RED for hot.
3. Insert the SPOUT through the hole on the mounting
surface making sure the RUBBER WASHER provided is
beneath the ESCUTCHEON and the HANDLE is aligned on
the RIGHT SIDE of the SPOUT.
NOTE: The HANDLE can ONLY be installed on the RIGHT
SIDE.

STYLE No. HNKM70, HN70KM
Henry One Hole Gooseneck Kitchen Faucet
with Pull-Down Spray and Metal Lever Handle
PAGE
3 OF 6 | UPDATED ON 5.9.2018
PRODUCT SUPPORT | 800.927.2120
| WATERWORKS.COM
INSTALLATION GUIDELINES
MOUNTING BRACKET
THREADED ROD
METAL WASHER
BARREL NUT
SUPPLY HOSE
4. Slide the MOUNTING BRACKET over the HOSES and
THREADED ROD, place the METAL WASHER onto the
THREADED ROD then thread and securely tighten the
BARREL NUT onto the THREADED ROD.
NOTE: Ensure the METAL WASHER fits properly around
the HOSES.
SLEEVE
SCREW
[LOOSEN ONLY]
[5mm HEX]
SCREW
[SECURELY
TIGHTEN]
WEIGHT
[ADJUST
POSITION]
WEIGHT
SLEEVE
SPRAY
HOSE
1.
2.
3.
[HOLE FOR
SPRAY HOSE]
SPOUT
SPRAY HOSE
[MALE END]
5. Loosen, but do NOT remove, the SCREW on the WEIGHT
using 5mm HEX KEY then remove the INTERNAL SLEEVE.
Place the SLEEVE over the NYLON SPRAY HOSE then
slide the WEIGHT over the SLEEVE then securely tighten
the SCREW to secure the WEIGHT in the desired position.
6. Insert the MALE END of the NYLON SPRAY HOSE through
the bottom of the SPOUT until it protrudes from the end
of the SPOUT.

STYLE No. HNKM70, HN70KM
Henry One Hole Gooseneck Kitchen Faucet
with Pull-Down Spray and Metal Lever Handle
PAGE
4 OF 6 | UPDATED ON 5.9.2018
PRODUCT SUPPORT | 800.927.2120
| WATERWORKS.COM
INSTALLATION GUIDELINES
CHECK
VALVE
SPRAY
SUPPLY
HOSE
FLOW
REGULATING
CHECK VALVE
ADAPTER
SPRAY HOSE
[FEMALE END]
WEIGHT
7. Thread and securely tighten the FEMALE END of the
NYLON SPRAY HOSE to the SUPPLY HOSE using the
ADAPTER provided.
NOTE: A FLOW REGULATING CHECK VALVE is located
inside the ADAPTER as well as an additional CHECK
VALVE.
HOT SUPPLY VALVE
[SOLD SEPARATELY]
SUPPLY HOSE ‡
COLD SUPPLY VALVE
[SOLD SEPARATELY]
SUPPLY HOSE ‡
‡ UK installations only!
2 BSPP ADAPTERS, 9/16"-24 UNEF Male x 3/8" Female BSPP,
for the SUPPLY HOSES are provided.
[CHECK FOR LEAKS!]
HANDLE
SPRAY
HOSE
* TURN ON THE WATER
COLD
HOT
ON
OFF
8. Connect the SUPPLY HOSES to the SUPPLY VALVES
[sold separately].
NOTE: The HOSES are connected to SUPPLY TUBES that
are marked BLUE for cold and RED for hot.
9. Turn on the water and operate the HANDLE to ensure it
functions properly and to flush out any debris in the
supply lines then check all connections for leaks and turn
off the water.
CAUTION: Flush out the supply lines prior to installing the
SPRAYER.

STYLE No. HNKM70, HN70KM
Henry One Hole Gooseneck Kitchen Faucet
with Pull-Down Spray and Metal Lever Handle
PAGE
5 OF 6 | UPDATED ON 5.9.2018
PRODUCT SUPPORT | 800.927.2120
| WATERWORKS.COM
INSTALLATION GUIDELINES
COLLAR
SPRAYER
O-RING
O-RING
COLLAR
SPRAY HOSE
10. Unthread and remove the COLLAR and O-RING from the
top of the SPRAYER then slide the COLLAR and O-RING
over the SPRAY HOSE.
SPRAYER
RUBBER
WASHER
SPRAY HOSE
O-RING
COLLAR
SPRAYER
O-RING
COLLAR
11. Thread and securely tighten the SPRAY HOSE into the
SPRAYER using the RUBBER WASHER provided.
12. Thread and securely tighten the COLLAR back onto the
SPRAYER making sure to include the O-RING.

STYLE No. HNKM70, HN70KM
Henry One Hole Gooseneck Kitchen Faucet
with Pull-Down Spray and Metal Lever Handle
PAGE
6 OF 6 | UPDATED ON 5.9.2018
PRODUCT SUPPORT | 800.927.2120
| WATERWORKS.COM
INSTALLATION GUIDELINES
WEIGHT
[ADJUST POSITION
IF OBSTRUCTED]
SET SCREW
[DO NOT
REMOVE OR
LOOSEN]
HANDLE
SPOUT
[360° SWIVEL]
TRIGGER
* TURN ON THE WATER
13. Turn on the water and operate the SPRAYER to ensure it
functions properly making sure the WEIGHT can move
freely beneath the cabinet and the SPOUT is able to swivel
properly. Adjust the position of the WEIGHT if necessary.
NOTE: Do NOT loosen or remove the SET SCREW at the
base of the SPOUT.
SET SCREW
[2.5mm HEX]
[DO NOT REMOVE]
CAP
RETAINING COLLAR
CARTRIDGE
SPOUT
GLAND COVER
HANDLE
SERVICING THE CARTRIDGE:
1. Remove the CAP at the base of the HANDLE then
unthread, but do NOT remove, the SET SCREW using the
2.5mm HEX KEY.
2. Remove the HANDLE, unthread and remove the GLAND
COVER, unthread and remove the RETAINING COLLAR
then remove the CARTRIDGE.