wattstopper LMCT-100 User manual

The LMCT-100 Wireless IR
Configuration Tool is a handheld
tool for setup and testing of
WattStopper Digital Lighting
Management (DLM) devices.
It provides wireless access
to occupancy and daylighting
sensors for setup and parameter
changes, WattStopper Push n’ Learn™ (PnL)
technology for load configuration, switch and
dimmer assignment and operating parameter
changes. The LMCT-100’s display shows menus
and prompts to lead you through each process.
The navigation pad provides a familiar way to
navigate through the customization fields. The
LMCT-100 allows modification of the system
without requiring ladders or tools; simply with a
touch of a few buttons.
User Guide
LMCT-100
Digital Configuration Tool
Patents Pending
Sensor Configuration............... 4
Load Configuration (PnL) ..... 13
Daylighting Configuration...... 17
Button Configuration ............. 78
Dimming Configuration ......... 85
Adjust Light Level.................. 90
Network Settings................... 91
Utilities................................... 70
Troubleshooting..................... 73
CONTENTS

2Operation
OPERATION
The LMCT-100’s IR transceiver allows bidirectional
communication between DLM devices and the
LMCT-100. Simple menu screens let you see the
current status of the system and make changes.
It can change any of the DLM occupancy sensor
parameters such as sensitivity, time delay and
more. With the LMCT-100 you can also change load
configurations, without any new wiring. For systems
including the LMLS-305 daylighting sensor the
LMCT-100 can also set or change the daylight level
parameters. The LMCT-100 can change dimming
system options such as scene assignments, fade
rates and other options not available through the
standard user interface.
BATTERIES
The LMCT-100 operates on three
standard 1.5V AAA Alkaline
batteries or three rechargeable
AAA NiMH batteries.
The battery status displays in the upper right
corner of the display. Three bars next to BAT=
indicates a full battery charge. A warning appears
on the display when the battery level falls below a
minimum acceptable level.
To conserve battery power, the
LMCT-100 automatically shuts off 10
minutes after the last key press.

3
Navigation
NAVIGATION
You navigate from one field to another using (up)
or (down) arrow keys. The active field is indicated
by flashing (alternates between yellow text on black
background and black text on yellow background).
Once active, use the Select
button to move to a menu
or function within the active
field.
Value fields are used
to adjust parameter
settings. They are shown in
“less-than/greater-than”
symbols: <value>. Once
active, change them using
(left) and(right) arrow
keys. In general thekey
increments and the key
decrements a value. Selections wrap-around if
you continue to press the key beyond maximum or
minimum values. Moving away from the value field
(using /keys) overwrites the original value.
The button takes you
to the main menu.
The button can
be thought of as an
un-do function. It takes
you back one screen.
Changes that were in
process prior to pressing
the key are lost.
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
Adjust Light Level
Home/
Main Menu
Up
Select
Down
Right/Next
Left
Back
Power
On/Off
IR Window
BAT=
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Value FieldsParameters
Function Fields (on Home Menu)
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
More
=
BAT

4Sensor Configuration - Current Settings
Home Menu
The Home (or Main) menu
displays after the power-
up process completes. It
contains information on
the battery status and six
menu choices.
Press /to locate the
desired function then press Select.
SENSOR CONFIGURATION  CURRENT SETTINGS
Sensor Configuration
Current Settings
Test Mode
Saved Configurations
Point to desired
Occupancy Sensor
Press ‘Select’
Press
Select
Press
Select
Point and
Press Select
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
More
=
BAT
This action enables com-
munication between the
sensor and the LMCT-100.
The sensor immediately
sends its current
parameter settings.
The screen changes to
show the current sensor settings where you can
adjust sensor parameters. “AH” next to Sensor
Config indicates that the sensor is currently in After
Hours mode. Changes made while AH is displayed
only affect After Hours operation.
Select
Button
Up or Down
Button
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
More
=
BAT

5
Adjusting Sensor Parameters
ADJUSTING SENSOR PARAMETERS
Using Current Settings, you can view all parameters
applicable to the type of sensor that is currently
communicating with the LMCT-100. You can modify
settings, send them to the sensor, and/or store them
in the LMCT-100.
Time Delay
Step 1: push or to
adjust the value.
Options:
<1 to 30 minutes>,
and <Override> to disable
the sensor
.
Step 2: push to activate
the next field.
Detection Sensitivity
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Adjust PIR
Sensitivity
Adjust
Ultrasonic
Sensitivity
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Press the
Down Arrow
for Ultrasonic
Step 1: push or to adjust the value. PIR and
Ultrasonic sensitivities vary from 0% to 100% in 10%
increments.
Note: Only sensitivity of technology that is present
can be changed.
Step 2: push to activate the next field.
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Adjust
Time Delay
Minutes

6Adjusting Sensor Parameters
Trigger/Retrigger Mode (Dual Tech Sensors only)
Step 1: push or to cycle through selections of
technology(ies) for the initial occupancy trigger:
PIR Only US (ultrasonic) Only PIR or US
PIR & US
Step 2: push to activate the next field.
Step 3: push or to cycle through technology
activations required to keep the load ON after the
initial occupancy is triggered.
Walk Through Mode
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Walk
Through
Mode
On or Off
Press the
down arrow to
choose Send,
Save or Receive
Walk-through mode
turns the load off three
minutes after the area
is initially occupied if no
motion is detected after
the first 30 seconds. If
motion continues
beyond the first 30
seconds, the selected
time delay applies.
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Adjust
Trigger
Mode
Adjust
Retrigger
Mode
Press the
Down Arrow
for Retrigger

7
Adjusting Sensor Parameters
Send
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Press
Select
Point and
Press Select
Configuration
Sent
Point to desired
Occupancy Sensor
Press ‘Select’
This sends the settings to the sensor.
The LEDs on the sensor blink to confirm the
message has been sent. To double-check that the
new settings were sent to the sensor, see “Receive.”
Save
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Choose
Save
Press
Select
Point and
Press Select
Saved Sensor Config
in Memory Slot 1
Press ‘Select’
This saves the settings in the LMCT-100 “Saved
Configurations” menu function for future use.
Each time you save a configuration the “Memory
Slot” number increases. You can save up to 9
configurations. Saved configurations are listed in the
LMCT-100’s “Saved Configurations” function in the
Sensor Configuration menu (for more details, see
page 12).

8Sensor Configuration - Test Mode
Receive
Important: Selecting Receive before sending new
settings to the sensor or saving them to LMCT-100
memory clears any value changes that you made.
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Point to desired
Occupancy Sensor
Press ‘Select’
Choose
Receive
Press
Select
Point and
Press Select
This retrieves the current settings from the sensor.
SENSOR CONFIGURATION  TEST MODE
Sensor Testing - Individual Sensor
Sensor Configuration
Current Settings
Test Mode
Saved Configurations
Press
Select
Press
Select
Press the
Down Arrow
for Test Mode
Point to desired
Occupancy Sensor
Press ‘Select’
Sensor Test Mode
Individual Sensor
All Sensors on bus
Point and
Press Select
Press
Select
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
More
=
BAT
The individual sensor goes into test mode.

9
Sensor Configuration - Test Mode
Adjusting Sensitivity during Test
For dual technology sensors, both technologies
appear on the screen, otherwise the screen only
presents the applicable technology.
PIR Sens = passive infrared sensitivity
US Sens = ultrasonic sensitivity
Adjust
PIR
Sensitivity
Adjust
Ultrasonic
Sensitivity
Press down
arrow for
Ultrasonic
Sensor Test
PIR Sens: <90%>
US Sens: <70%>
Detection : <PIR Only>
SEND RECEIVE EXIT
Sensor Test
PIR Sens: <90%>
US Sens: <70%>
Detection : <PIR Only>
SEND RECEIVE EXIT
You can adjust sensitivity values while inside the Test
Mode. Values are 0 to 100%, in 10% increments.
Detection Criteria (Dual Technology Sensors only)
Select
Detection
technology
Press
down arrow
for Detection
Sensor Test
PIR Sens: <90%>
US Sens: <70%>
Detection : <PIR & US>
SEND RECEIVE EXIT
You can select to test one
or the other technology,
or both technologies
together. Selections cycle
through:
PIR US PIR or US
PIR &US

10 Sensor Configuration - Test Mode
Send
Press
Select
Point and
Press Select
Point to desired
Occupancy Sensor
Press ‘Select’
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Sensor Test
PIR Sens: <90%>
US Sens: <70%>
Detection : <PIR Only>
SEND RECEIVE EXIT
Configuration Sent
Test Mode starts using
the settings you sent.
Receive
Choose
Receive
Press
Select
Point and
Press Select
Point to desired
Occupancy Sensor
Press ‘Select’
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Sensor Test
PIR Sens: <90%>
US Sens: <70%>
Detection : <PIR Only>
SEND RECEIVE EXIT
Retrieves settings from the sensor so you can view
or modify them for further testing.

11
Sensor Configuration - Test Mode
Exit Test Mode
To Exit Test Mode
Point to
Occupancy Sensor
Press ‘Select’
Sensor Config
Time Delay: <20 min>
PIR Sens: <90%>
US Sens: <70%>
Trigger : <PIR Only>
Retrigger: <PIR Only>
Walkthru: <Off>
SEND SAVE RECEIVE
Sensor Test
PIR Sens: <90%>
US Sens: <70%>
Detection : <PIR Only>
SEND RECEIVE EXIT
Choose
Exit
Press
Select
Point and
Press Select
Sensor Testing - All Sensors on Bus
Press
Select
Point to any
Occupancy Sensor
Press ‘Select’
Sensor Test Mode
Individual Sensor
All Sensors on bus
Point and
Press Select
When you select “All Sensors on bus”, you can test
the selected sensor along with other sensors on
the DLM Local Network (bus) to understand the
coverage in the entire room.

12 Saved Configurations
SAVED CONFIGURATIONS
Note: If no saved configurations exist, you will see:
No Sensor Configurations exist, Press ‘Select’.
Sensor Configuration
Current Settings
Test Mode
Saved Configurations
Press
Select
Press
Select
Press the
Down Arrow for
Saved Configurations
Saved Sensor Configs
Pick DT Saved Config
<1 20/90/70/W >
RECALL DELETE
Deleted Sensor Config
in Memory Slot 2
Press ‘Select’
Point to desired Type
of Occupancy Sensor
to retrieve saved
configurations for
that sensor type
Press ‘Select’
Press
Select
Press
Select
To Review the Config
Settings Select
RECALL:
Press
Select
Press
Select
To Delete the Saved
Config Select
DELETE:
Press the
Right or
Left Arrow
to view other
Saved Configs
Saved Sensor Configs
Pick DT Saved Config
<2 5/80/70 >
RECALL DELETE
Saved Sensor Configs
Pick DT Saved Config
<2 5/80/70 >
RECALL DELETE
Sensor Config
Time Delay: <5 min>
PIR Sens: <80%>
US Sens: <70%>
Trigger : <PIR & US>
Retrigger: <PIR or US>
Walkthru: <Off>
SEND SAVE
Press
Select
Press the
Down Arrow
for SAVE
Memory
Slot Number
(up to 9 per
sensor type)
Up to 4 enabled settings, e.g.:
20....Time Delay minutes
90....% PIR Sensitivity
70....% US Sensitivity
W...Walkthrough Enabled
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
More
=
BAT

13
Load Configuration (PnL)
LOAD CONFIGURATION PnL
Use the Load Configuration function to identify
load numbers, view and change load parameters
and load bindings to sensors. You initiate Load
Configuration (PnL) also known as Push n’ Learn™
by pointing the LMCT-100 at any IR enabled DLM
Local Network device when prompted.
Important: To configure load binding from the
LMCT-100, it must be initiated by the LMCT-100. After
entering PnL you must exit before using the system.
Press
Select
Press
Select
Point to any IR
enabled device on
the network
Press ‘Select’
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
More
=
BAT
When the device receives the signal from the LMCT-
100, the DLM Local Network goes into PnL mode;
the red LED on all communicating devices starts
blinking at 2x/second and all loads turn OFF except
Load 1 turns ON.
Load Selection
Settings for load 1
appear first.
Push to highlight
NEXT and push the
SELECT button to turn
ON the next load and
view its settings.
Right arrow
to change
setting for
load 1
Down arrow to
highlight NEXT
then SELECT
to go to next
load
Load Config <PnL>
Load: 1
Operation: <Auto On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT

14 Load Configuration (PnL)
Operation Mode
The operation mode
determines if the load can
be turned on automatically
by a sensor, or only
manually by a switch. Push
or to adjust the
Operation mode. Options
are ‘Auto On’ and ‘Manual
On’.
Blink Warning
The Blink Warning flashes the load OFF then ON one
minute prior to the sensor automatically turning the
load OFF when the time delay expires.
Push or to adjust
the Blink Warning. Options
are ‘Disable’ and ‘Enable’.
LMLS-105
Load Config <PnL>
Load: 1
Operation: <Auto On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Daylighting
<Disable>
or <Enable>
This function enables and
disables an LMLS-105
daylighting sensor to
control the selected load.
Load Config <PnL>
Load: 1
Operation: <Auto On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Operation Mode
<Manual On>
or <Auto On>
Load Config <PnL>
Load: 1
Operation: <Auto On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Blink Warning
<Disable>
or <Enable>

15
Load Configuration (PnL)
Load Config <PnL>
Load: 1
Operation: <Auto On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Press
Select
Point to any IR
enabled device on
the network
Point and
Press Select
Press ‘Select’
Configuration Sent
Press <SELECT> to
Continue
or <HOME> to exit PnL
Load Config <PnL>
Load: 1
Operation: <Auto On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Choose
Bind
Press
Select
Point to desired
Occupancy Sensor to
bind to Load
Point and
Press Select
Press ‘Select’
Send
New settings have been
sent to the selected load.
Wait 5-6 seconds for the
message to clear. Select
another function (bind,
next, exit). To instantly
end load configuration
press the HOME key.
Bind
Binds the occupancy sensor to the selected load.

16 Load Configuration (PnL)
Next
Select another load. When NEXT is selected, Load 1
turns OFF and Load 2 turns ON.
Exit
This ends the configuration function and exits PnL.
Load Config <PnL>
Load: 1
Operation: <Auto On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Point to any IR
enabled device on
the network
Point and
Press Select
Choose
Exit
Press
Select
Press ‘Select’
Load Config <PnL>
Load: 1
Operation: <Auto On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Choose
Next
Press
Select
Press
Select
Choose
desired
Load
Point to any IR
enabled device
Press ‘Select’
Select Load
Load: <2>
Adjust settings
as necessary.
Press
Select
Load Config <PnL>
Load: 2
Operation: <Manual On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Load Config <PnL>
Load: 2
Operation: <Manual On>
Blink: <Disable>
LMLS-105: <Disable>
SEND BIND NEXT EXIT
Press
Select
Point to any IR
enabled device on
the network
Point and
Press Select
Press ‘Select’
Configuration Sent
Press <SELECT> to
Continue
or <HOME> to exit PnL

17
Daylighting Configuration
DAYLIGHTING CONFIGURATION
Daylighting Config allows you to setup daylighting
and operation parameters specific to the type of
sensor that is communicating with the LMCT-100.
Different menu options are displayed depending
upon the device. To configure daylighting for the
LMLS-400, LMLS-500 or LMLS-600 refer to page 21.
Note regarding IR communication with the
LMLS-600: Because of the great mounting heights
of skylight sensors in high-bay applications, it
is important to stand directly underneath the
photosensor, with the LMCT held in a vertical
orientation pointed at the bottom of the sensor.
In some cases, direct communications between the
LMCT and the LMLS-600 may be difficult to achieve
due to interference from very high ambient light
when looking up, from direct sunlight, high intensity
fluorescent fixtures (e.g.,T5HO) mounted close to the
sensor, as well as some other intense light sources.
In these cases, communications can be established
with the photosensor by aiming the LMCT at another
DLM product on the network (e.g., a wall swtich or
occupancy sensor).

18 Daylighting Configuration
Daylighting Config (LMLS-305/LS-301 only)
Refer to the LMLS-305 installation instructions for
details about daylighting setup and operation.
Day Setpoint
Press
Select
Daylighting Config
(LMLS-305/LS-301)
Choose setpoint
press ‘Select’
Setup: <Day>
Daylighting Config
(LMLS-305/LS-301)
Use the Up/Down Keys
to set the desired
Day light level
Day Setup
Daylighting Config
(LMLS-305/LS-301)
Decrementing the
Light level
Day Setup
Daylighting Config
(LMLS-305/LS-301)
When done adjusting
press Select
Day Setup
Press
Select
Daylighting Config
(LMLS-305/LS-301)
Day Setup
Day Setpoint Saved
Press Up or Down arrow
to adjust light level
Increment (raise)
Decrement (lower)
Daylighting Config
LMLS-305/LS-301
LMLS-400
LMLS-500
LMLS-600
Press
Select
Choose
LMLS-305/
LS-301
Daylighting Config
LMLS-305/LS-301
LMLS-400
LMLS-500
LMLS-600
Press
Select
Press
Select
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
More
=
BAT
Choose
LMLS-305/
LS-301
Choose
Daylighting
Config

19
Daylighting Configuration
Night Setpoint
Press
Select
Daylighting Config
(LMLS-305/LS-301)
Choose setpoint
press ‘Select’
Setup: <Night>
Daylighting Config
(LMLS-305/LS-301)
Use the Up/Down Keys
to set the desired
Night light level
Night Setup
Daylighting Config
(LMLS-305/LS-301)
Decrementing the
Light level
Night Setup
Daylighting Config
(LMLS-305/LS-301)
When done adjusting
press Select
Night Setup
Press
Select
Daylighting Config
(LMLS-305/LS-301)
Night Setup
Night Setpoint Saved
Press Up/Down
arrow to adjust
light level
Daylighting Config
(LMLS-305/LS-301)
Choose setpoint
press ‘Select’
Setup: <Day>
Press Left/Right
arrow to scroll to
Night Setpoint
Press
Up/Down
arrow
Increment (raise)
Decrement (lower)

20 Daylighting Configuration
Auto Setpoint
This function allows the LMLS-305 to automatically
begin electric light adjustment.
Press
Select
Daylighting Config
(LMLS-305/LS-301)
Choose setpoint
press ‘Select’
Setup: <Auto>
Daylighting Config
(LMLS-305/LS-301)
Automatic Mode
Enabled
Daylighting Config
(LMLS-305/LS-301)
Choose setpoint
press ‘Select’
Setup: <Day>
Press Left/Right
arrow to scroll to
Auto Setpoint
Press the Home Button to return to the Home Page.
Press
Home
Daylighting Config
(LMLS-305/LS-301)
Choose setpoint
press ‘Select’
Setup: <Auto>
Sensor Configuration
Load Config (PnL)
Daylighting Config
Button Configuration
Dimming Configuration
More
=
BAT