Waveshare 10451 User manual

1.3inch OLED User Manual
1
Rev 2.4, May 15th 2015
share awesome hardware
1.3inch OLED
User Manual
1. Key Parameters
Table 1: Key Parameters
Driver Chip
SH1106
Interface
3-wire SPI、4-wire SPI、I2C
Resolution
128*64
Display Size
1.3 inch
Dimension
29mm*33mm
Colors
Yellow, Blue
Visible Angle
>160°
Operating Temp. (℃)
-20℃~70℃
Storage Temp. (℃)
-30℃~80℃
2. Operation Description
We will illustrate the usage of the module with an example of 4-wire SPI mode (default working mode)
by connecting Waveshare Open103R development board (STM32F103R MCU on board).
2.1. Hardwar e configuration
This module provides 3 kinds of driver interfaces; they are 3-wire SPI, 4-wire SPI and I2C interface. In
its factory settings, BS0/BS1 pins are set to 0/0 and 4-wire SPI is selected as default.
Different working mode and pin function of the module can be set by hardware selection on BS0/BS1
pins. (Notice: In this operation, welding is required. Any changes under no guidance from Waveshare
will be considered as a waiver of warranty).
Table 2: Working mode setting
name
mode
BS1/BS0
CS
D/C
DIN
CLK
3-wire SPI
0/1
CS
0
MOSI
SCLK
4-wire SPI
0/0
CS
D/C
I2C
1/0
0
0/1
SDA
SCL

1.3inch OLED User Manual
2
Rev 2.4, May 15th 2015
share awesome hardware
2.2. Softwar e configuration
Open the project file .\IDE\ OLED.uvproj in Keil, navigate to the following text, delete the ‘//’ (Double
slash) before #define INTERFACE_4WIRE_SPI
//#define INTERFACE_3WIRE_SPI //3-wire SPI
#define INTERFACE_4WIRE_SPI //4-wire SPI
//#define INTERFACE_IIC //I2C
After compiling successfully, download the project to Open103R development board.
Note: You should delete the ‘//’ (Double slash) corresponding to the mode selection
2.3. Hardwar e connections
Connect module to the SPI2 interface of Open103R development board, power up. OLED displays
information as Figure 1 shows..
Figure 1: OLED information display

1.3inch OLED User Manual
3
Rev 2.4, May 15th 2015
share awesome hardware
3. 4-wire SPI and I2C interfaces of SH1106 OLED
The 8080-Parallel Interface, 6800-Parallel Interface, Serial Interface (SPI) or I2C Interface can be
selected by different selections of IM0~2 as shown in Table 3:
Table 3: Different selections of IM0~2
(SH1106_V2.3.pdf Chap. Functional Description)
Note1: When Serial Interface (SPI) or I2C Interface is selected, D7~D2 is Hz. D7~ D2 is recommended
to connect the VDD1 or VSS. It is also allowed to leave D7~ D2 unconnected.
SH1106 provides 5 kinds of driver interfaces, however the OLED board just provides 3 kinds of driver
interfaces settling (3-wire SPI, 4-wire SPI and I2C. the IM2 pin is set to “1” by hardware). BS0, BS1
correspond to IM0, IM1 respectively. We introduce 4-wire SPI and I2C interfaces here. Please read
SH1106_V2.3.pdf for more details.
3.1. 4 Wire Serial Interface (4 -wir e SPI)
The serial interface consists of serial clock SCL, serial data SI, A0 and CS . SI is shifted into an 8-bit shift
register on every rising edge of SCL in the order of D7, D6, … and D0. A0 is sampled on every eighth
clock and the data byte in the shift register is written to the display data RAM (A0=1) or command
register (A0=0) in the same clock. See Figure 2:
Table 4: SPI interface setting
(SH1106_V2.3.pdf Chap. 4 Wire Serial Interface)
Note: “-” pin must always be HIGH or LOW. D7~ D2 is recommended to connect the VDD1 or VSS. It is
also allowed to leave D7~ D2 unconnected.

1.3inch OLED User Manual
4
Rev 2.4, May 15th 2015
share awesome hardware
The serial interface is initialized when CS is high. In this state, SCL clock pulse or SDI data have no
effect. A falling edge on CS enables the serial interface and indicates the start of data transmission.
The SPI is also able to work properly when the CS always keep low, but it is not recommended.
Figure 2: 4-wire SPI data transfer
(SH1106_V2.3.pdf Chap. 4 Wire Serial Interface)
When the chip is not active, the shift registers and the counter are reset to their initial statuses.
Read is not possible while in serial interface mode.
Caution is required on the SCL signal when it comes to line-end reflections and external noise.
We recommend the operation be rechecked on the actual equipment.
3.2. I2C-bus Interface
The SH1106 can transfer data via a standard I2C-bus and has slave mode only in communication. The
command or RAM data can be written into the chip and the status and RAM data can be read out of
the chip.
Table 5: I2C-bus Interface
(SH1106_V2.3.pdf Chap. I2C-bus Interface)
Note: “-” pin must always be HIGH or LOW. D7~ D2 is recommended to connect the VDD1 or VSS. It is
also allowed to leave D7~ D2 unconnected.
Software configuration
Open the project file .\IDE\ OLED.uvproj in Keil. After compiling successfully, download the project to
Open103R development board.
CS signal could always pull low in I2C-bus application.

1.3inch OLED User Manual
5
Rev 2.4, May 15th 2015
share awesome hardware
The I2C-bus is for bi-directional, two-line communication between different ICs or modules. The two
lines are a serial data line (SDA) and a serial clock line (SCL). Both lines must be connected to a
positive supply via a pull-up resistor. Data transfer may be initiated only when the bus is not busy.
Note: The positive supply of pull-up resistor must equal to the value of VDD1.
Bit Transfer
One data bit is transferred during each clock pulse. The data on the SDA line must remain stable
during the HIGH period of the clock pulse as changes in the data line at this time will be interpreted as
a control signal.
Figure 3: Bit Transfer
(SH1106_V2.3.pdf Chap. I2C-bus Interface)
Start and Stop conditions
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the
data line, while the clock is HIGH is defined as the START condition (S). A LOW-to-HIGH transition of
the data line while the clock is HIGH is defined as the STOP condition (P).

1.3inch OLED User Manual
6
Rev 2.4, May 15th 2015
share awesome hardware
Figure 4: Start and Stop conditions
Acknowledge
Each byte of eight bits is followed by an acknowledge bit. The acknowledge bit is a HIGH signal put on
the bus by the transmitter during which time the master generates an extra acknowledge related
clock pulse. A slave receiver which is addressed must generate an acknowledge after the reception of
each byte. Also a master receiver must generate an acknowledge after the reception of each byte that
has been clocked out of the slave transmitter. The device that acknowledges must pull-down the SDA
line during the acknowledge clock pulse, so that the SDA line is stable LOW during the HIGH period of
the acknowledge related clock pulse (set-up and hold times must be taken into consideration). A
master receiver must signal an end of data to the transmitter by not generating an acknowledge on
the last byte that has been clocked out of the slave. In this event the transmitter must leave the data
line HIGH to enable the master to generate a stop condition.
Figure 5: Acknowledge
Protocol
The SH1106 supports both read and write access. The R/W bit is part of the slave address. Before any
data is transmitted on the I2C-bus, the device that should respond is addressed first. Two 7-bit slave
addresses (0111100 and 0111101) are reserved for the SH1106. The least significant bit of the slave

1.3inch OLED User Manual
7
Rev 2.4, May 15th 2015
share awesome hardware
address is set by connecting the input SA0 to either logic 0(VSS) or 1 (VDD1). The I2C-bus protocol is
illustrated in Figure 6: I2C Protocol. The sequence is initiated with a START condition (S) from the
I2C-bus master that is followed by the slave address. All slaves with the corresponding address
acknowledge in parallel, all the others will ignore the I2C-bus transfer. After acknowledgement, one
or more command words follow which define the status of the addressed slaves. A command word
consists of a control byte, which defines Co and D/C (note1), plus a data byte (see Figure 6: I2C
Protocol). The last control byte is tagged with a cleared most significant bit, the continuation bit Co.
After a control byte with a cleared Co-bit, only data bytes will follow. The state of the D/C -bit defines
whether the data-byte is interpreted as a command or as RAM-data. The control and data bytes are
also acknowledged by all addressed slaves on the bus. After the last control byte, depending on the
D/C bit setting, either a series of display data bytes or command data bytes may follow. If the D/C bit
was set to ‘1’, these display bytes are stored in the display RAM at the address specified by the data
pointer. The data pointer is automatically updated and the data is directed to the intended SH1106
device. If the D/C bit of the last control byte was set to ‘0’, these command bytes will be decoded and
the setting of the device will be changed according to the received commands. The acknowledgement
after each byte is made only by the addressed slave. At the end of the transmission the I2C-bus
master issues a stop condition (P). If the R/W bit is set to one in the slave-address, the chip will output
data immediately after the slave-address according to the D/C bit, which was sent during the last
write access. If no acknowledge is generated by the master after a byte, the driver stops transferring
data to the master.
Figure 6: I2C Protocol

X-ON Electronics
Largest Supplier of Electrical and Electronic Components
Click to view similar products for OLED Displays & Accessories category:
Click to view products by Waveshare manufacturer:
Other Similar products are found below :
OLED-100H008A-RPP5N00000 OLED-100H016B-RPP5N00000 OLED-200H016A-LPP5N00000 OLED-100H008A-GPP5N00000 OLED-
100H008A-LPP5N00000 OLED-100H032A-BPP5N00000 UG-2864KSWLG01 DEP 128160A-W OLED-100H016F-RPP5N00000 OLED-
100H016A-LPP5N00000 OLED-128Y032A-WPP3N00000 OLED-100H016A-WPP5N00000 OLED-100H016H-GPP5N00000 OLED-
016O002B-BPP5N00000 OLED-096Y064A-LPP3N00000 OLED-096O064A-BPP3N00000 OLED-128Y064C-LPP3N00000 OLED-
096Y064B-LPP3N00000 OLED-128Y032A-LPP3N00000 OLED-096Y064B-BPP3N00000 REH012864KYPP3N00F00 HDSP-U111-EG000
REC001601BWPP5N00100 REG010016FBPP5N00100 REG010016FGPP5N00100 REG010016FWPP5N00100 REG010032AWPP5N00100
REX064128AWPP3N0Y000 14747 REA160128AYPP3N00000 REN025664DGPP3L00000 REN025664DYPP3L00000 104020248 10451
19750 19376 19299 16103 10507 10444 13992 14657 10514 9085 REG010008AGPP5N00000 REG010008AWPP5N00000
REG010016CRPP5N00000 REG010016DBPP5N00000 REG010016ERPP5N00000 REG010032BYPP5N00000