WaveSplitter WST-PSP002 User manual
Copyright © 2020 Wavesplitter AV Technology |Wavesplitter .com
OPERATION MANUAL
Model No. WST-PSP002
HDMI 2.0 4K@60Hz 1x2 Splitter
Safety Instruction
Introduction 標題:英文字體-Arial (粗體) / 字型 12 內文: 英文字體-Arial / 字型 9
The WST-PEX004 is a simple to use plug and play solution which lets the user extend HDMI signals up to 50m using a single low
cost Cat.6 U/UTP cable (not included). For added convenience IR signals (20-60 kHz) can also be extended using the supplied IR
Receiver and Emitter cables.
Supporting resolutions up to Full HD 1920x1080p@60Hz, video content can be seen with incredible clarity at distances up to 50m,
perfect for use in a variety of AV and digital signage applications in a range of settings.
The Extender features an HDMI loop-through output on the Transmitter with simultaneous viewing so that a local display can be
connected for monitoring or to create an additional viewing zone. To ensure the maximum compatibility when two displays are
connected, the EDID data, which determines the supported video and audio formats, can be used from either a local monitor
connected to the Transmitter or the remote monitor connected to the Receiver.
Power over Cat.6 (PoC) functionality enables the Extender to operate from a single power supply connected to the Transmitter,
allowing the Receiver to be located where there is limited access to mains power sockets making it ideal for retro fit installations.
Copyright © 2020 Wavesplitter AV Technology |Wavesplitter .com
OPERATION MANUAL
Introduction
WST-PSP002 allows you to split a single HDMI source signal simultaneously to two HDMI displays. It supports resolutions up to 4K@60Hz. An
impressive feature for this model is that it supports different resolutions output at the same time. It also supports three EDID modes, user can
switch to the best one based on the environment and reach the best compatibility. WST-PSP002 is perfect for security system, advertisement
demonstration, home theater system, etc.
Key Feature
⚫One HDMI input, two HDMI outputs.
⚫Supports resolutions up to 4K@60Hz, 4:4:4, HDR10.
⚫Available to output one 4K and one 1080P resolution at the same time.
⚫Supports HDCP1.4 & 2.2.
⚫Supports CEC, ARC on output port 1.
⚫Supports 3D.
⚫Supports audio format: LPCM 7.1, Dolby TrueHD, Dolby digital Plus, DTS-HD Master Audio.
⚫Supports EDID management including Copy, UHD and FHD.
⚫Supports firmware update by USB port.
Package Content
1x2 Splitter x 1 | USB Type-A to Micro-B cable x 1
Panel Description
Copyright © 2020 Wavesplitter AV Technology |Wavesplitter .com
OPERATION MANUAL
EDID Instruction
⚫Copy Mode：
It will learn the output display’s EDID connected to output 1. output 2 will display the same resolution as output 1.
If output 1 is not connected to any display, output 2 will display 4K@60HZ.
If output 1 is connected to a display supporting HDR, this product is able to learn and support HDR10.
⚫UHD Mode：
Default EDID is 4K@60HZ. Supports different resolutions output at the same time.
⚫FHD Mode：
Default EDID and the highest supported resolutions is 1080P@60HZ.
Connection Instruction
1. Connect HDMI source devices to the splitter’s input ports by a HDMI cable.
2. Connect the splitter’s output ports to HDMI displays by a HDMI cable.
3. If no display shown, please connect the attached USB Type-A to Micro-B cable to a 5V1A PSU.
Diagram
Copyright © 2020 Wavesplitter AV Technology |Wavesplitter .com
OPERATION MANUAL
Specification
Interface
Inputs
HDMI Type-A (Female) x 1
Outputs
HDMI Type-A (Female) x 2
Transmission
HDMI standard
HDMI 2.0
HDCP standard
1.4 / 2.2
Resolutions
4096x2160@60Hz / 3840x2160@60Hz / 1920x1200@60Hz / 1920x1080P@60Hz
Power
Power supply (Optional)
5V/1A DC
Power consumption
1W
Environment
Operating Temperature
0˚C～40˚C
Storage Temperature
-20˚C～60˚C
Product structure
Housing Material
Metal
Dimension (W x D x H)
61 x 93. x 15mm
Weight
120g
Certification
Safety
CE / FCC / RoHS / REACH
COO
China
Table of contents
Other WaveSplitter Media Converter manuals
