WBOX Technologies 0E-24EVGHDMI User manual

0E-24EVGHDMI
0E-27EVGHDMI
ECO ENERGY EFFICIENT
LED COLOR MONITOR Tech Support
#833-574-9124(Option2)
[e-mail]

1
Contents
Contents ...................................................................................................................................... 1
Safety.......................................................................................................................................... 1
Cautions....................................................................................................................................... 3
FCC RF Interference Statement ....................................................................................... 4
Connections................................................................................................................................. 5
Controls & Menu Operation.............................................................................................. 6
Mounting Guide ................................................................................................................ 12
Accessories................................................................................................................................ 13
Power Indicator / Modes of Operation............................................................................ 13
Dimensions ............................................................................................................................... 14
Specifications................................................................................................................ 15
Limited Warranty........................................................................................................... 16
Safety
1. Read these instructions completely and comply with all requirements.
2. Retain these instructions for reference.
3. Comply with all instructions and warnings, both in this manual and on the product.
4. Disconnect the monitor from all power before cleaning. Use a damp cloth for
cleaning; and do not use liquid or aerosol cleaners.
5. Never use the monitor in damp areas or near water.
6. Never place the monitor on an unstable surface; if the monitor falls it may cause
serious damage to people or property.
7. When selecting a location for placement/installation please ensure:
A. To allow for sufficient ventilation leave a minimum distance of 4” around the monitor.
B. Never allow anything (e.g. paper, cloth, etc.) to obstruct the monitor ventilation
openings.
C. Never allow an open flame source (e.g. lighted candles) near the monitor.
Super ECO Sensing Functions................................................................................................................... 5

2
D. If batteries are used, please dispose of all batteries as per local regulations.
E. Use the monitor in indoor environments as per the temperature and humidity specs.
8. The monitor should be operated from a power source indicated on the rear of the monitor.
9. The 3 wire grounding type plug [having a third (grounding) pin] used on this monitor is a
safety feature. Do not power the monitor without a grounding-type plug.
10. Do not place the monitor where people can step on the cord or allow anything to rest
on or rub against the power cord.
11. If an extension cord is used to power the monitor, make surethat the total ampere
usage of all the products plugged into the extension cord does not exceed the ampere
rating of the extension cord nor the power rating of the outlet.
12. To avoid the risk of fire or an electric shock resulting from contact with dangerous
voltage points or damage to parts, never insert objects of any kind into the monitor
cabinet slots. Never spill any kind of liquid on the monitor.
13. Do not attempt to service this monitor yourself, as opening or removing the cover may
expose you to dangerous voltage points or other risks.
14. If any of the following occur, disconnect the power to the monitor and refer
servicing to qualified service personnel:
A. The power cord or plug is damaged or frayed.
B. If liquid has been spilled into the monitor.
C. If the monitor has been exposed to rain, water or other liquids.
D.If the monitor does not operate as expected as per the operating instructions.
Adjust only those settings as described in the operating instructions; improper
adjustment of other controls may cause the monitor to become inoperative and
may void the warranty.
E. If the monitor has been dropped or the cabinet has been damaged.
F. If the monitor exhibits a distinct change in performance, indicating a need
for service.
Please note:
The power supply cord is used as the main disconnect device. Ensure that the power
outlet is located/installed near the monitor and is easily accessible.

3
Cautions
Only specially qualified personnel should open the case. No user serviceable parts inside.
To prevent electrical shock or a fire hazard, do not expose the monitor to rain or
moisture. This monitor is designed to be used in a residential or commercial
environment. Do not subject the monitor to excessive vibration or dust, or to corrosive
materials.
Ventilation slots are provided on the cabinet to control the internal temperature of the
monitor. Do not cover these ventilation holes or place anything on the unit which
might block those slots.
Avoid placing the monitor in direct sunshine or near a heating appliance.
Do not use the monitor against a bright background or where sunlight and other light
sources will shine directly on the monitor.
Neither the monitor itself nor any other heavy object should rest on the power cord.
Damage to a power cord can cause fire or electrical shock.
POWER SUPPLY CORD IS USED AS MAIN POWER
DISCONNECT DEVICE IN THIS PRODUCT. UNPLUG THIS
PRODUCT FROM THE WALL OUTLET BEFORE REMOVING
THE BACK COVER AND SERVICING.
CAUTION TO SERVICE PERSONNEL
1. Never open the monitor case
2. Do not use in environments that may cause hazards.
3. Keep in a well-ventilated location.
4. Avoid excessive heat.
5. To eliminate eye fatigue.
6. Be careful of heavy objects.

4
FCC RF Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment causes harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures.
oReorient or relocate the receiving antenna.
oIncrease the space between the equipment and receiver.
oConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
oOnly a shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved
by the grantee or manufacturer could void the user's authority to operate such equipment.
DOC Compliance Notice
This digital apparatus does not exceed the Class A limit for radio noise emissions from
digital apparatus set out in the radio interference regulation of Canadian Department of
Communications.
CE Compliance
This monitor complies with the basic protection requirements of the
Electromagnetic Compatibility (EMC) Directive 2014/30/EU for electrical
and electronic equipment imported into the European Union (EU):
The electromagnetic disturbance generated by the apparatus does not exceed the
level specified in the harmonized EMC Standards for this type of apparatus. It has a
level of immunity to the electromagnetic disturbance to be expected in its intended
use, and should operate without unacceptable degradation of its specified
performance.

Connections
Back View of Monitor
Connector panel is located on
the underside of the case rear
projection, just above the stand.
Detailed View of the Connector
Panel.
Induction function range: within 2-4 meters, 79-157 inch.
When there is no person or person in a static state more than 30 seconds in the induction
range, the screen brightness will automatically reduce to the lowest, in order to achieve the
purpose of energy saving.
When there is activity in the induction range, the screen will be automatically adjusted to the
preset brightness.
Small movement such as shoulder movement, hand lifting and other body movements can be
detected.
Minor movements such as opening mouth, blinking eyes, finger movements and shaking head
can not be detected.
The super ECO sensing function default is OFF.
5
Super ECO Sensing Functions

Controls & Menu Operation
Control Keys / Buttons
Buttons are located on the right side of the
BACKCASE on ALL models, looking at the
backside of the monitor.
Source Auto detection function when there
is/are source(s) connect to the monitor, monitor
will auto detect the source(s) and auto select
the desired source. The source should be
selected manually when there is more than
one source to the monitor.
A. (SOURCE) button
To change the input selection, press
to display the pop-up menu,
use up/down to highlight the desired
then press left/right to complete
the selection.
To verify the current input selection,
press to display the pop-up,
then press“M(MENU) ”again to
dismiss the pop-up.
●Press the button to display
all the signal channel menus.
When Main MENU display as
confirmation key during the
OSD operation
B. (MENU) button“ M ”
●Press the button to show the On-Screen Display main menu.
●Press the button to exit OSD menu.
C.
6
(LEFT) button“ ”
●Press the button, volume decrease.
Press the button to scroll the cursor to desired function.
D.
(RIGHT) button“ ”
●Press the button, volume increase.
E. (POWER) button
●Press the button to turn ON or turn OFF the monitor.
“ E ”
“ E ”
“ E ”
“ E ”
EM
“ ”
Auto Select
VGA
HDMI

7
Picture Menu
Relating to the MENU main screen as per below -
● Press MENU - show MENU screen.
● The menu has 3 columns and multiple rows. Red text shows current position within the
menu.
● Using the arrows - allows to go up/down the specific menu column.
● Pressing E - Once or twice - will get you out of the Menu display.
● Say, we are on Picture setting ( red text ), the other 2 columns show related sub-menus
for this setting. To go to column 2 to deal with sub-menu settings - Press MENU, then one
can use arrows to scroll up/down the functions.
● For example - we are on Picture Setting --> press MENU--> brings us to 2nd column -->
using arrows, placing red text on Anti Burn-in --> pres MENU again will take us to the 3rd
column --> pressing MENU again, will allow us to choose ON/OFF settings.
● Once we are done, press E once, twice, 3 times to leave MENU screen.
Picture Setting
Color Setting
Input Source
Display Setting
Other Setting
Super ECO
Anti Burn-In
DCR
On
On
Off
Off
Brightness
Low Blue Light
Flicker free
Contrast
Information 100
50
0

8
Picture Setting
Super ECO: Allows the user to select ON/OFF the Super ECO model.
Anti Burn-In: Allows the user to select between ON/OFF.
Low Blue Light: Adjust the Low Blue Light 0-100.
Flicker free: Allows the user to select between ON/OFF.
DCR: Allows the user to select ON/OFF the DCR model.
Brightness: Adjusts the overall picture brightness.
Contrast: Adjusts the range of difference between light and dark areas of the picture.
Gamma: Allows the user to select ON/OFF the gamma model.
Color Temp.: Allows the user to select the sRGB,9300K, 6500K, 7500K, User Color.
When set the color Temperature to "USER" model, can adjust the Red, Green, Blue value.
Red: Adjust the red 0-100.
Green: Adjust the green 0-100.
Blue: Adjust the blue 0-100.
Color Setting
Picture Setting
Color Setting
Input Source
Display Setting
Other Setting
Gamma
Color Temp.
Red
Off
6500K
Green
Blue
Information
50
50
50

9
Interface options are VGA, HDMI,Auto Select.
Input Source
Picture Setting
Color Setting
Input Source
Display Setting
Other Setting
Auto Select
VGA
HDMI
Information
Picture Setting
Color Setting
Input Source
Display Setting
Other Setting
AspectRatio
Auto Adjust
Auto Color
Full
H.Position
V.Position
Clock
Phase
Information 50
50
50
50

10
AspectRatio: Allows the user to select the Full, 4:3, Over Scan.
H.Position: Adjust the h.position 0-100.
V.Position: Adjust the v.position 0-100.
Clock: Adjust the clock 0-100.
Phase: Adjust the phase 0-100.
Display Setting(VGA model Only)
Language: Choose OSD display language from English/French/Spanish
Italian /Netherlands/Polish/Czech/Danish
Volume: Adjust the volume 0-100.
Mute: Allows the user to select ON/OFF the mute model.
OSD H.Position: Adjust the osd h.position 0-100.
OSD V.Position: Adjust the osd v.position 0-100.
OSD Timeout: Adjust the osd timeout 0-100 seconds .
Reset: Restore initial settings.
Other Setting
Picture Setting
Color Setting
Input Source
Display Setting
Other Setting
Language
Volume
Mute
English
Off
OSD H.Position
OSD V.Position
OSD Timeout
Reset
Information
50
30
50
10

11
Resolution:1920x1080. H.freq 68 KHz. V.freq 60 Hz.
Information
Picture Setting
Color Setting
Input Source
Display Setting
Other Setting
1920 x 1080
H.freq 68 KHz
V.freq 60 Hz
Information

12
Mountin g Guide
Wall or Other Mounting with VESA Standard
Note: Metric M4-L8 mm is the type scerw that should be used (do not use longer
screws or the monitor may be damaged).
1. Before mounting the monitor, remove the base riser (vertical portion of the base) by
removing the four screws near the top with a screwdriver. Then the base and the
riser can be removed. In order to prevent losing these screws, we suggest replacing
the screws in their original holes.
2. Attach the VESA mounnt (0E-24EVGHDMI(100mm x 100mm)(0E-27EVGHDMI
(100mm x 100mm)) plate to rear of the monitor andfollow all of the instructions provided
with the mount to complete the mounting process.
CAUTION The wall mount must bear a minimum of ve times the
monitor’s net weight. To mount your MONITOR to the wall or
another surface,you need to purchase a VESA wall mount.Use four
(M4-L8 mm screws (the base attachment screws removed in step 1
below are(M4-L8 mm)to attach the mount.The monitor mount VESA
hole pattern is (0E-24EVGHDMI (100mmx100mm) 0E-27EVGHDMI
(100mmx100mm))

13
Accessories
Power Indicator / Modes of Operation
LED Indicator
LED is off when power is off, LED glows green when power is on AND there is a video
INPUT, LED glows red when monitor is sleep/standby mode. The power management
feature of the monitor is designed for security surveillance applications.
When there is NO video input and the power is ON, "No signal" shows for few seconds
then having black Screen. when signal is provided, the monitor changes state from
sleep/standby to active mode.
Power Cable
Qty: 1
Screws Type: Metric M4-L8 mm Qty: 4
Screw for Mounting Monitor
HDMI Cable
Qty: 1
Stand support
Qty: 1
Base of stand
Qty: 1 Qty: 2
User Manuals
LED Indicator
VGA Cable
Qty: 1

14
Dimensions
Model
Letter Dimension
A Width of monitor body
B Height of monitor body
C Depth of monitor body
D Height of monitor on base
E Width of base
F Depth of base
G Width of viewable area
H Height of viewable area
I Thickness of monitor
inch
24.1
14.3
1.9
17.7
8.4
7.4
23.9
13.4
0.6
0.7
0.1
inch
20.2
12.6
1.7
16.1
8.4
7.4
21
11.9
0.5
0.5
0.1
J Bottom bezel width
K Side bezel width
mm
363.5
614.1
49.5
450.7
214.6
190
607.1
342.8
15
17.2
3.5
mm
321.8
514.4
43.8
409
214.6
190
535
303.6
14.3
15
3.2
B
A
D
EF
H
C
I
J
K
G
0E-24EVGHDMI 0E-27EVGHDMI

15
Specifications
Model 0E-24EVGHDMI 0E-27EVGHDMI
Screen diagonal dimension (inches)
Viewable area W x H (inches)(mm)
23.8
20.74x11.67(527.04×296.46)
0.2745×0.2745
LED
27
23.53x13.24(597.888×336.312)
0.3114×0.3114
1920x1080
1080
Led Type
Pixel pitch (mm)
Screen maximum Resolution
Display Resolutions 720x400;640x480;800x600;1024x768;1280x1024;1366x768;1920x1080
720x400;640x480;800x600;1024x768;1280x1024;1366x768;1920x1080Supported Input Resolutions
Refresh Rate 60
16.7
250
Yes
16:9
Color Depth (million)
Brightness (cd/m²）
Auto Adjust
Monitor Aspect Ratio
Display Aspect Ratio OSD selectable 16:9 or 4:3
Horizontal TV Lines
Contrast Ratio 1000:1 SCR
Response Time (ms) 8 (GTG)
View Angle H/V (degrees) 178°x 178°/CR＞10
Digital Video Inputs HDMI up to 1920 x 1080
Analog Video In/Out VGA up to 1920 x 1080
1x3.5mm mini-jack
20W Typical
21.3”x12.6”x1.7”
(541.4×321.8×43.8mm)
(541.4×409×190mm)
21.3”x16.1”x7.5”
100x100
＜0.5
Matte black
Plastic
Yes
-5°~15°
AC 100-240V~50/60Hz 1.8A
0°C~40°C / 32℉~104℉
-20°C~50°C / -4℉~122℉
10~90%
6.9Ibs(3.15 Kg) 9.7Ibs(4.4 Kg)
7.7Ibs(3.5 Kg) 10.5Ibs(4.8 Kg)
Power cable/VGA cable/HDMI cable/screws/stand/user manual
CE/FCC/ROHS/HDMI/UL/WEEE/REACH
Audio In (stereo)
26W Typical
24.1”x14.3”x1.9”
(614.4×363.5×49.5mm)
(614.4×450.7×190mm)
24.1”x17.7”x7.5”
Stand-by (W)
Power Consumption
Monitor Body Dimensions
Dimension Monitor + Stand
Panel Surface
Case & Stand Material
VESA Mounting pattern (mm)
Base/Stand included
Base/Tilt Angle
Monitor Weight
Monitor + Base Weight
Power supply (internal)
Operating Temperature
Storage Temperature
Operating Humidity
Accessories
Rack Mount screw Size (mm)
Certifications
Warranty 30 Months
2x2
Speakers(W)
Screw for Mounting Monitor, Screws Type: M4-L8 mm/4pcs

16
Limited Warranty
1. Limited Warranty
A. General
Subject to the terms and conditions of this Limited Warranty, from the date of sale
through the period of time for product categories specified in Section 1(b), ADI warrants
its W Box Technologies products to be free from defects in materials and workmanship
under normal use and service, normal wear and tear excepted. Except as required by
law, this Limited Warranty is only made to Buyer and may not be transferred to any third
party.
ADI shall have no obligation under this Limited Warranty or otherwise if:
(I) The product is improperly installed, applied or maintained;
(II) The product is installed outside of stated operating parameters, altered, or
improperly services or repaired;
(III) Damage is caused by outside natural occurrences, such as lightning, power
surges, fire, floods, acts of nature, or the like.
(IV) Defects resulting from unauthorized modification, misuse, vandalism, or other
causes unrelated to defective materials or workmanship, or failures related to
batteries of any type used in connection with the products sold here under.
ADI only warrants those products branded as W Box Technologies products and sold by
ADI. Any other products branded by third parties are warranted by the third party
manufacturer for a period as defined by the third party manufacturer, and ADI assigns to
Buyer those warranties and only those warranties extended by such third party
manufacturers or vendors for non-ADI branded products. ADI does not itself warrant any
non-ADI branded product and sells only on an as is basis in accordance with ADI’s
terms and conditions of sale.

17
B. Specific Warranties for Product Categories
Product Categories Warranty
CCTV Power Supplies
24 months
Monitors 30 months
Video Baluns 30 months
Analog Cameras 36 months
DVRs, NVRs (excluding HDD) 60 months
IP Cameras
60 months
Racks
60 months
TV Mounts
60 months
Analog Cables Limited Lifetime
B Connectors Limited Lifetime
Extension Cords Limited Lifetime
HDMI Cables Limited Lifetime
Jacks, Cords and Intrusion
Limited Lifetime
Patch Cables
Limited Lifetime
Wire Ties
Limited Lifetime
2. Exclusion of Warranties, Limitation of Liability
THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF
MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE,
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE
FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL ADI BE LIABLE TO
ANYONE FOR ANY (I) CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR
PUNITIVE DAMAGES ARISING OUT OF OR RELATING IN ANY WAY TO THE PRODUCT
AND.OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR CONDITION,
EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER,
EVEN IF THE LOSS OR DAMAGE IS CAUSED BY ADI’S OWN NEGLIGENCE OR FAULT
AND EVEN IF ADI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR
DAMAGES.

18
Any product description (whether in writing or made orally by ADI or ADI’s agents),
specifications, samples, models, bulletin, drawings, diagrams, engineering sheets, or
similar materials used in connection with the Buyer's order are for the sole purpose of
identifying ADI's products and shall not be construed as an express warranty or condition.
Any suggestions by ADI or ADI's agents regarding use, applications or suitability of the
products shall not be construed as an express warranty or condition unless confirmed to
be such in writing by ADI. ADI does not represent that the products it sells may not be
compromised or circumvented; that the products will prevent any personal injury
or property loss by burglary, robbery, fire or otherwise, or that the products will in all cases
provide adequate warning or protection. Buyer understands and will cause its customer to
understand that a properly installed and maintained product is not insurance or guarantee
that such will not cause or lead to personal injury or property loss. CONSEQUENTLY ADI
SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR
OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THAT THE
PRODUCT FAILED TO GIVE WARNING. However, if ADI is held liable whether directly or
indirectly for any loss or damage with respect to the products it sells, regardless of cause or
origin, its maximum liability shall not in any case exceed the purchase price of the product,
which shall be fixed as liquidated damages and not as a penalty and shall be the complete
and exclusive remedy against ADI.
FOR THE AVOIDANCE OF DOUBT, ADI DOES NOT SEEK HEREUNDER TO EXCLUDE
OR RESTRICT ITS LIABILITY IN RELATION TO (I) FRAUD, (II) DEATH OR PERSONAL
INJURY DIRECTLY RESULTING FROM ITS NEGLIGENCE OR (III) ANY MATTER IN
RESPECT OF WHICH, BY LAW, IT IS NOT PERMITTED TO RESTRICT ITS LIABILITY.
3. Limitation on Liability to Buyer’s Customers
Buyer agrees to limit liability to its customers to the fullest extent permitted by law. Buyer
acknowledges that ADI shall only be deemed to give consumers of its products such
statutory warranties as may be required by law and at no time shall Buyer represent to its
customers and/or users of ADI products that ADI provides any additional warranties. By
accepting the products, to the fullest extent permitted by law, Buyer assumes all liability for,
and agrees to indemnity and hold ADI harmless against and defend ADI from, any and all
suits, claims, demands, causes of action and judgments relating to damages, whether for
personal injury or to personal property, suffered by
any person, firm, corporation or business association, including but not limited to, Buyer's
customers and/or users of the products because of any failure of the products to detect
and/or warn of the danger for which the goods were designed or any other failure of the
products whether or not such damages are caused or contributed to by the sold or joint
concurring negligence or fault of ADI.

19
4. Returns
Subject to the terms and conditions listed below, during the applicable warranty period,
ADI will replace Product or provide a credit at purchase at its sole option free of charge
any defective products returned prepaid. Any obligations of ADI to replace Limited
Lifetime warranty products pursuant to this warranty which result from defect are limited
to the availability of replacement product. ADI reserves the right to replace any such
products with the then currently available products, or provide a credit in its sole
discretion. In the event Buyer has a problem with any ADI product, please call your local
ADI branch for return instructions:
WWW.WBOXTECH.COM
Be sure to have the model number and the nature of the problem available. In the event of
replacement, the return product will be credited to Buyer's account and a new invoice
issued for the replacement item. ADI reserves the right to issue a credit only in lieu of
replacement.
If any WBox Technologies product is found to be in good working order or such
product's inability to function properly is a result of user damage or abuse, the
product will be returned to Buyer in the same condition as received and Buyer shall
be responsible for any return freight changes.
5. Governing Law
This Limited Warranty shall be governed by the laws of England and Wales.
6. Miscellaneous
Where any term of this Limited Warranty is prohibited by such laws, it shall be null and void,
but the remainder of the Limited Warranty shall remain in full force and effect.