WDH LIGHT LINK EZ-5645S User manual

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
1/10
We all know that the relay is a certain life, the relay inside
the metal reed will be damaged, then need to rely on
professionals to repair replacement, not only the high cost
and more disputes.
The new design of the S5645 to complete the maintenance
and replacement to overcome the problem, each relay
device is easy to replace the modular structure, the
efficient future maintenance, to avoid the maintenance
process of the many problems.
The new design of the 5645S also confused the previous
engineering staff to solve the actual lighting feedback
problems, with current sensing components RL-PB01 can
accurately and efficiently identify the actual light switch
status, "WYSIWYG" has been the system operator Efforts
to implement the objectives, using 5645S will make your
project planning more perfect!
Easy To
Replacement
Introduction

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
2/10
Before starting the installation, please read the instructions
 Do not install the unit in a wet location, and there is a danger of electric shock
 Please follow the instructions to fix the machine, to avoid loose shaking
 After installation, check whether the wiring is correct before turning on the power
 Strictly prohibit any disassembly modification, demolition or modification shall be
deemed to give up the machine warranty interest
 When the machine fails, please contact the engineering staff immediately repair
EZ-5645S can be fixed to the aluminum rail
Appearances

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
3/10
 6 groups of independent removable relay module, easy maintenance
(RL-PB01 can be purchased)
 A / B double contact automatic detection, can be connected with the
wall panel switch full double-cut switch
 Each circuit can store the actual load memory
 Detect the minimum current value 3W, such as LED drive can also set
the memory
 Each circuit A / B independent contacts at least 10A
 With a complete protocol, you can specify a single loop or group on /
off action
 RS485 can be connected to any standard protocol system host
 Software or hardware can set the ID, easy to implement
multi-machine control
 With 6 groups of independent IO can be connected to the general wall
switch panel, the system host executable control
 With a total set of IO contacts can be set according to demand the
implementation of the loop
 With serial output function, can be expanded to 12 loops
 With the implementation of the state indicator, display working status
 With communication status T / R indicator
 With 6 single-loop button and indicator function, can be controlled by
hardware keys
 With 6 single-loop fuses, instantaneous overload for instant security
 With the connection of the wall switch panel, each circuit will be OFF
after re-transmission
 Two fixing methods are available, one for standard aluminum rails
and the other for direct screw fixation
Specifications

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
4/10
Dimensions and product packaging accessories:
Dimension: 285 * 143.5 * 53.5 mm
Weight: 1762.5 grams (including PB01 * 6)
Input power: DC12V 2A(above)
Control voltage: AC 110 ~ 220V
Maximum load:
Single loop 20A (B connected to load / A not connected to wall switch)
Single loop 10A (B connected to load / A connected to wall switch)
* The above load should be added "instantaneous current"
Current consumption:
standby current> 70mA / operating current> 450mA
Packing: environmental carton
Safety regulations: CE / FCC
DC12V Input
Total DI
Single DI * 6
Indicators * 5_
POWER
STATUS / M/S
TXATUS / RX
M/S terminal
Rs485 terminal
Button & indicator_
Set*1
Total*1
Single*6 & indicator*6
Detachable relay
module
Hardware

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
5/10
 RL-PB01
Relay with detection module * 6
 2 PIN Terminal blocks * 9
 4 PIN Terminal blocks *1
 Removable fixed iron * 2
 Fixing screws * 4
Optional accessories: standard aluminum rail clip AE-005
B
A
Accessories

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
6/10
Installation location & Note:
Ventilation is good, not moisture, to avoid the location of children to touch
Do not touch! Unless you turn off the power to avoid electric shock
1 2
4 3
Follow the steps below to remove the fixed iron plate at the bottom of the
5645S, and attach it to fix the machine
Installed & Fixed

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
7/10
Such as the left picture
General lighting switch circuit installation
wiring, through the command of the 5645S
control action
Each RL-PB01 is planned A / B double
contact
The middle point for the input, B contact load
current higher than the A contact
5645S only control the load≧3
W
of light or power equipment
And can not be used as a dry
contact switch controller
Electric load configuration
Control load requirements
Master Slave
Double-cut switch
Load
Be careful the polarity

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
8/10
Digital contacts can be
connected to the general control
of the wall switch
The general switch includes:
Single-cut switch or Bell switch
According to the configuration of
different switch types, 5645S
contact mode can be set by
command
General
switch
General
switch
Double-cut switch configuration;
The use of wall double-cut switch
and 5645S integrated into a true
double-cut switch, or even 5645S
failure! Wall switch can also be
normal control of light power
Regardless of the state of the wall
switch is on or off, the system
host can read from 5645S current
li
g
ht
p
ower status
Double-cut switch
Load
Load
Digital DI contact switch
AC contact switch

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
9/10
5645S relay is a modular detachable
structure, fault replacement please follow
the instructions
RL-PB01
relay
modular
Press here
Push the module
forward
Up &
Remove
RL-PB01
RL-PB01
Do not touch the
gold-plated metal contact
with your hand
Remove & replacement

Six Loop Switch Controller
LIGHT LINK EZ-5645S
Copyright © 2016 by WDH.,CO
All rights reserved. No part of this document may be reproduced by any means,
without written permission of the copyright owner. http://www.wdh.com.tw
10/10
EZ-5645S & LED specific dimmer & Tungsten(TRICK) dimmer.
Can constitute a multi-loop light control system
EZ-5645S Six loops switch controller
EZ-L816F Six output LED dimmer
EZ-D496F Four loop tungsten light dimmer
Complete lighting & power control solution